Chapter 1

Physics for Scientists and
Engineers
Introduction
and
Chapter 1
Physics
 Fundamental Science
 concerned with the basic principles of the Universe
 foundation of other physical sciences
 Divided into major areas as
 Classical Mechanics
 Relativity
 Thermodynamics
 Electromagnetism
 Optics
 Quantum Mechanics
Classical Physics
 Mechanics and electromagnetism are basic
to all other branches of classical physics
 Classical physics developed before 1900
 Our study will start with Classical
Mechanics
 Also called Newtonian Mechanics
Classical Physics
 Includes Mechanics
 Major developments by Newton, and continuing
through the latter part of the 19th century
 Thermodynamics
 Optics
 Electromagnetism
 All of these were not developed until the latter part
of the 19th century
Modern Physics
 Began near the end of the 19th century
 Phenomena that could not be explained by
classical physics
 Includes theories of relativity and quantum
mechanics
Classical Mechanics Today
 Still important in many disciplines
 Wide range of phenomena that can be
explained with classical mechanics
 Many basic principles carry over into other
phenomena
 Conservation Laws also apply directly to
other areas
Objective of Physics
 To find the limited number of fundamental
laws that govern natural phenomena
 To use these laws to develop theories that
can predict the results of future experiments
 Express the laws in the language of
mathematics
Theory and Experiments
 Should complement each other
 When a discrepancy occurs, theory may be
modified
 Theory may apply to limited conditions
 Example: Newtonian Mechanics is confined to objects
traveling slowing with respect to the speed of light

Try to develop a more general theory
Quantities Used
 In mechanics, three basic quantities are used
 Length
 Mass
 Time
 Will also use derived quantities
 These are other quantities can be expressed in
terms of these
Standards of Quantities
 Standardized systems
 agreed upon by some authority, usually a
governmental body
 SI – Systéme International
 agreed to in 1960 by an international
committee
 main system used in this text
Length
 Units
 SI – meter, m
 Defined in terms of a meter – the
distance traveled by light in a vacuum
during a given time
Table 1.1, p. 5
Mass
 Units
 SI – kilogram, kg
 Defined in terms of a kilogram, based
on a specific cylinder kept at the
International Bureau of Standards
Table 1.2, p. 5
Standard Kilogram
The National Standard Kilogram

No. 20, an accurate copy of the
International Standard Kilogram
kept at Sèvres, France, is housed
under a double bell jar in a vault
at the National Institute of
Standards and Technology.
Time
 Units
 seconds, s
 Defined in terms of the oscillation of
radiation from a cesium atom
Table 1.3, p. 6
Number Notation
 When writing out numbers with many
digits, spacing in groups of three will be
used
 No commas
 Examples:
 25 100
 5.123 456 789 12
Reasonableness of Results
 When solving a problem, you need to
check your answer to see if it seems
reasonable
 Reviewing the tables of approximate
values for length, mass, and time will
help you test for reasonableness
Systems of Measurements
 US Customary
 everyday units
 Length is measured in feet
 Time is measured in seconds
 Mass is measured in slugs
 often uses weight, in pounds, instead of mass
as a fundamental quantity
Prefixes
 Prefixes correspond to powers of 10
 Each prefix has a specific name
 Each prefix has a specific abbreviation
Prefixes
 The prefixes can
be used with any
base units
 They are
multipliers of the
base unit
 Examples:
 1 mm = 10-3 m
 1 mg = 10-3 g
Model Building
 A model is a system of physical
components
 Identify the components
 Make predictions about the behavior of the
system
 The predictions will be based on interactions
among the components and/or
 Based on the interactions between the
components and the environment
Models of Matter
 Some Greeks
thought matter is
made of atoms
 JJ Thomson (1897)
found electrons and
showed atoms had
structure
 Rutherford (1911)
central nucleus
surrounded by
electrons
Models of Matter
 Nucleus has structure, containing
protons and neutrons
 Number of protons gives atomic number
 Number of protons and neutrons gives
mass number
 Protons and neutrons are made up of
quarks
Modeling Technique
 Important technique is to build a model
for a problem
 Identify a system of physical components
for the problem
 Make predictions of the behavior of the
system based on the interactions among
the components and/or the components
and the environment
Density
 Density is an example of a derived
quantity
 It is defined as mass per unit volume
m

V
 Units are kg/m3
Table 1.5, p.9
Atomic Mass
 The atomic mass is the total number of
protons and neutrons in the element
 Can be measured in atomic mass
units, u
 1 u = 1.6605387 x 10-27 kg
Basic Quantities and Their
Dimension
 Dimension has a specific meaning – it
denotes the physical nature of a
quantity
 Dimensions are denoted with square
brackets
 Length [L]
 Mass [M]
 Time [T]
Dimensional Analysis
 Dimensional Analysis is a technique to check
the correctness of an equation or to assist in
deriving an equation
 Dimensions (length, mass, time,
combinations) can be treated as algebraic
quantities
 add, subtract, multiply, divide
 Both sides of equation must have the same
dimensions
Symbols
 The symbol used in an equation is not
necessarily the symbol used for its dimension
 Some quantities have one symbol used
consistently
 For example, time is t virtually all the time
 Some quantities have many symbols used,
depending upon the specific situation
 For example, lengths may be x, y, z, r, d, h, etc.
Dimensional Analysis
 Given the equation: x = ½ at 2

 Check dimensions on each side:
L
L  2  T2  L
T
 The T2’s cancel, leaving L for the

dimensions of each side
 The equation is dimensionally correct
Conversion of Units
 When units are not consistent, you may need

to convert to appropriate ones
 Units can be treated like algebraic quantities
that can cancel each other out
 See the inside of the front cover of your
textbook for an extensive list of conversion
factors
Conversion
 Always include units for every quantity, you
can carry the units through the entire
calculation
 Multiply original value by a ratio equal to one
 Example
15.0 in  ? cm
 2.54 cm 
15.0 in   38.1 cm
 1 in 
Significant Figures
 A significant figure is one that is reliably
known
 Zeros may or may not be significant
 Those used to position the decimal point are not
significant
 To remove ambiguity, use scientific notation
 In a measurement, the significant figures
include the first estimated digit
Significant Figures
 0.0075 m has 2 significant figures

 The leading zeros are placeholders only
 Can write in scientific notation to show more clearly:
7.5 x 10-3 m for 2 significant figures
 10.0 m has 3 significant figures
 The decimal point gives information about the reliability
of the measurement
 1500 m is ambiguous
 Use 1.5 x 103 m for 2 significant figures
Operations with Significant Figures –
Multiplying or Dividing
 When multiplying or dividing, the number of

significant figures in the final answer is the
same as the number of significant figures in the
quantity having the lowest number of significant
figures.
 Example: 25.57 m x 2.45 m = 62.6 m2
 The 2.45 m limits your result to 3 significant
figures
Operations with Significant Figures –
Adding or Subtracting
 When adding or subtracting, the number of

decimal places in the result should equal the
smallest number of decimal places in any
term in the sum.
 Example: 135 cm + 3.25 cm = 138 cm
 The 135 cm limits your answer to the units
decimal value
Operations With Significant Figures –
Summary
 The rule for addition and subtraction are
different than the rule for multiplication and
division
 For adding and subtracting, the number of
decimal places is the important
consideration
 For multiplying and dividing, the number of
significant figures is the important
consideration
Rounding
 Last retained digit is increased by 1 if the last
digit dropped is 5 or above
 Last retained digit remains as it is if the last
digit dropped is less than 5
 If the last digit dropped is equal to 5, the
retained digit should be rounded to the
nearest even number
 Saving rounding until the final result will help
eliminate accumulation of errors
Problem solving tactics
 Explain the problem with your own words.

 Make a good picture describing the problem
 Write down the given data with their units. Convert all
data into S.I. system.
 Identify the unknowns.
 Find the connections between the unknowns and the data.
 Write the physical equations that can be applied to the
problem.
 Solve those equations.
 Check if the values obtained are reasonable  order of
magnitude and units.
Reasonableness of Results
 When solving a problem, you need to check
your answer to see if it seems reasonable
 Reviewing the tables of approximate values
for length, mass, and time will help you test
for reasonableness

Chapter 1

Uploaded by

Copyright:

Available Formats

Chapter 1

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Chapter 1

Uploaded by

Copyright:

Available Formats

Physics for Scientists and

The National Standard Kilogram

 Given the equation: x = ½ at 2

 The T2’s cancel, leaving L for the

 When units are not consistent, you may need

 0.0075 m has 2 significant figures

 When multiplying or dividing, the number of

 When adding or subtracting, the number of

 Explain the problem with your own words.

You might also like