Scribd
Upload
57 views

Routing Overview - Static Route

Routers have components like a CPU, RAM, and network adapters. They use routing tables to forward packets based on destination addresses. Routers learn routes dynamically from routing protocols or have static routes configured manually. Dynamic routing protocols allow routers to automatically adjust to topology changes while static routes must be configured by network administrators. Routers use metrics like administrative distance to determine the best routes to destinations.

Uploaded by

Đinh Tú
Copyright
© © All Rights Reserved
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
57 views

Routing Overview - Static Route

Routers have components like a CPU, RAM, and network adapters. They use routing tables to forward packets based on destination addresses. Routers learn routes dynamically from routing protocols or have static routes configured manually. Dynamic routing protocols allow routers to automatically adjust to topology changes while static routes must be configured by network administrators. Routers use metrics like administrative distance to determine the best routes to destinations.

Uploaded by

Đinh Tú
Copyright
© © All Rights Reserved
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
You are on page 1/ 20

Exploring the Functions of Routing

BSCI v3.0—2-1
Routers

Cisco 2800 Series Router

• Routers have the following components:


– CPU
– Motherboard
– RAM
– ROM
• Routers have network adapters to which IP addresses are assigned.
• Routers may have the following two kinds of ports:
– Console: For the attachment of a terminal used for management
– Network: Different LAN or WAN media ports
• Routers forward packets based upon a routing table.
Router Operations

A router needs to do the following:


• Know the destination address.
• Identify the sources from which the router can learn.
• Discover possible routes to the intended destination.
• Select the best route.
• Maintain and verify routing information.
Router Operations (Cont.)

 Routers must learn destinations that are not directly connected.


Router Functions

RouterX# show ip route


D 192.168.1.0/24 [90/25789217] via 10.1.1.1
1 R 192.168.2.0/24 [120/4] via 10.1.1.2 2
O 192.168.3.0/24 [110/229840] via 10.1.1.3

1. Lets other routers know about changes


2. Determines where to forward packets
Identifying Static and Dynamic Routes

Static route Dynamic route


• Uses a route that a • Uses a route that a
network administrator network routing protocol
enters into the router adjusts automatically for
manually topology or traffic
changes
Dynamic Routing Protocols
Autonomous
AS 10
System 10 Autonomous
AS 20System 20
IANA

EGP
Exterior Gateway
BGP Protocols
IGP
RIP, EIGRP,
Interior GatewayOSPF
Protocols
Distance Link-state
Vector
Hybrid
Routing Tables
Routing Table Entries

• Directly connected: Router attaches to this network


• Static routing: Entered manually by a system administrator
• Dynamic routing: Learned by exchange of routing information
• Default route: Statically or dynamically learned; used when no
explicit route to network is known
AD - Administrative Distance
AD - Administrative Distance

Protocol AD Value (0-255)


Connected 0
Static 1
EIGRP 90
OSPF 110
RIP 120
Routing Metrics
Load Balancing

10.0.0.0/8
R1
Enabling Static Routing

BSCI v3.0—2-14
Static Routes

 Configure unidirectional static routes to and from a stub


network to allow communications to occur.
Static Route Configuration

RouterX(config)# ip route network [mask]


{address | interface}[distance] [permanent]

• Defines a path to an IP destination network or subnet or host


• Address = IP address of the next hop router
• Interface = outbound interface of the local router
Static Route Example

RouterX(config)#ip route 172.16.1.0 255.255.255.0 172.16.2.1


or
RouterX(config)#ip route 172.16.1.0 255.255.255.0 s0/0/0

 This is a unidirectional route. You must have a route configured in the


opposite direction.
Default Routes

 This route allows the stub network to reach all known networks
beyond Router A.
Verifying the Static
Route Configuration

RouterX# show ip route


Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, * - candidate default
U - per-user static route
 
Gateway of last resort is 0.0.0.0 to network 0.0.0.0
 
10.0.0.0/8 is subnetted, 1 subnets
C 10.1.1.0 is directly connected, Serial0/0/0
S* 0.0.0.0/0 is directly connected, Serial0
[email protected]

You might also like