Scribd
Upload
162 views23 pages

BASIC TELEPHONY (Full Chapter)

Here are the key differences between local battery and central battery exchanges: - In a local battery exchange, the dry cells used to power the subscriber's telephone handset are located at the subscriber's premises. In a central battery exchange, the batteries are located centrally at the telephone exchange. - Local battery exchanges required subscribers to have magneto generators to signal the exchange when they wanted to make a call, as the local batteries did not provide enough power for signaling over long lines. Central battery exchanges used signaling powered by the central batteries. - Central battery exchanges allowed for longer subscriber lines as the central batteries provided consistent powering of signaling over greater distances compared to local batteries.

Uploaded by

black widow
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
162 views23 pages

BASIC TELEPHONY (Full Chapter)

Here are the key differences between local battery and central battery exchanges: - In a local battery exchange, the dry cells used to power the subscriber's telephone handset are located at the subscriber's premises. In a central battery exchange, the batteries are located centrally at the telephone exchange. - Local battery exchanges required subscribers to have magneto generators to signal the exchange when they wanted to make a call, as the local batteries did not provide enough power for signaling over long lines. Central battery exchanges used signaling powered by the central batteries. - Central battery exchanges allowed for longer subscriber lines as the central batteries provided consistent powering of signaling over greater distances compared to local batteries.

Uploaded by

black widow
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 23

Chapter 1

BASIC TELEPHONY
 Telecommunication deals with the service of
providing electrical communication at a
distance.
 The service may be private or open to public

correspondence (i.e., access).


 The public switched telecommunication
network (PSTN) is consists of hundreds of
smaller networks interconnected.
Centralized Switching Systems
Switching Systems
Telecommunication Network
Basic of a Switching System
 Key components of a switching system or an
exchange are the set of input and output
circuits called inlets and outlets, respectively.
 The primary function of a switching system

is to establish an electrical path between a


given inlet-outlet pair.
 The hardware used for establishing such a

connection is called the switching matrix or


the switching network.
 When N = M, the switching network is called
a symmetric network.
 The inlets/outlets may be connected to local subscriber lines or
to trunks from or to other exchanges as illustrated in Figure 2.
In the figure, four types of connections can be established:

1. Local call connection between two subscribers in the same


exchange
2. Outgoing call connection between a subscriber and an
outgoing trunk, i.e to another exchange
3. Incoming call connection between an incoming trunk (from
another exchange) and a local subscriber
4. Transit call connection between an incoming trunk and an
outgoing trunk.
Folded Switching Network

In a folded network with N subscribers, there can be a maximum


of N/2 simultaneous calls or information interchanges. The
switching network may be designed to provide N/2
simultaneous switching paths, in which case the network is said
to be nonblocking.
In a nonblocking network, as long as a called subscriber is free,
a calling subscriber will always be able to establish a connection
to the called subscriber.
Non-Folded Networks
In a switching network, all the inlet/outlet connections may be
used for inter-exchange transmission. In such a case, the
exchange does not support local subscribers and is called a
transit (or tandem) exchange. A switching network of this kind
is called a non folded network.

In a non-folded network with N inlets and N outlets, N


simultaneous information transfers are possible. Consequently,
for a non folded network to be non blocking, the network should
support N simultaneous switching paths.
Elements of a Switching System
Manual Switching Systems
The earliest manual exchange systems used a battery at the subscriber end to
energize the microphone in the subscriber's handset - such an exchange is
called a "local battery" or "LB" exchange. Later, batteries were located at the
exchange end, and such an exchange is known as a "central battery" or "CB"
exchange.

i) Local Battery Exchange:


 In "LB" systems, the dry cells used at the subscriber end to power the microphone had
limited power and so could not be used for signaling over long lines to the exchanges.
 Hence, LC subscriber sets were provided with a magneto generator to operate indicators
at the exchange.
 The magneto generator was operated by the caller cranking the magneto handle on the
handset to generate a substantial current, which would send a signal to activate an
indicator at the exchange, telling the operator that someone wished to make a call.
ii) Central Battery Exchange:
The system consists of one or more switchboards manned by operators. The
subscriber lines are terminated on jacks mounted on the switchboard.
Associated with each jack is a light indicator to draw the attention of the
operator.
When a subscriber lifts the hand set, the off-hook switch is closed, causing a
current to flow through the hand set and the lamp relay coil. The lamp relay
operates and the indicator corresponding to the subscriber lights up. The
operator establishes contact with the subscriber by connecting the head set to
the subscriber line via the headset key and a plug-ended cord pair.
On being told the number required by the subscriber, the operator verifies whether
the called party is free, and if so, sends out the ringing current to the called
subscriber using a plug-ended cord pair. The ringing circuit at the subscriber end
was a bell, with a capacitor C, in series. They remain connected to the circuit
always. The capacitor allows the alternating ringing current from the exchange to
pass through the bell but prevents the loop direct current. If the called party is
busy, the calling subscriber is told about the same. When the called party answers,
his indicator lamp lights up. The operator then establishes a connection between
the calling and the called party by plugging in the cord pair to the called party
jack.
LIMITATIONS OF MANUAL SWITCHING SYSTEM:

 In a manual exchange the subscriber needs to


communicate with the operator and common
language becomes an important factor.

 Sufficient Privacy is not there as an operator is


involved in setting up and monitoring the call.

 Moreover, the operator takes a few minutes to


establish and release of calls.
Switchboards
 When the number of subscribers increases,
multiple switchboards and operators are
required to handle the traffic.

 The switchboard may be two types:


i) Single Termination Switchboard and
ii) Multi termination Switchboard.
Single Termination Switchboard
Multi Termination Switchboard
Home Task
 Comparison between Local Battery and
Central Battery Exchange.
 Comparison between Single Transmission and

Multi Transmission Switchboard.

You might also like