Chapter 4

Solver Settings

Introduction to
ANSYS CFX

ANSYS, Inc. Proprietary Release 13.0

© 2010 ANSYS, Inc. All rights reserved. 4-1 December 2010
Solver Settings
Overview Training Manual

• Initialization

• Solver Control

• Output Control

• Solver Manager

Note: This chapter considers solver settings for steady-state simulations.

Settings specific to transient simulation are discussed in a later chapter.

ANSYS, Inc. Proprietary Release 13.0

© 2010 ANSYS, Inc. All rights reserved. 4-2 December 2010
Solver Settings
Initialization Training Manual

• Iterative solution procedures require that all solution variables are

assigned initial values before calculating a solution

• A good initial guess can reduce the solution time

• In some cases a poor initial guess may cause the solver to fail
during the first few iterations

• The initial values can be set in 3 ways:

1. Solver automatically calculates the initial values
2. Initial values are entered by the user
3. Initial values are obtained from a previous solution

• Initial values can be set on a per-domain basis or globally for all

domains

ANSYS, Inc. Proprietary Release 13.0

© 2010 ANSYS, Inc. All rights reserved. 4-3 December 2010
Solver Settings
Initialization – Setting Initial Values Training Manual

• Insert Global Initialisation

from the toolbar or by right-
clicking on Flow Analysis 1

• Edit each Domain to set initial

values on a per-domain basis
– When both are defined the
domain settings take
precedence
– Solid domain must have
initial conditions set on a per-
domain basis

ANSYS, Inc. Proprietary Release 13.0

© 2010 ANSYS, Inc. All rights reserved. 4-4 December 2010
Solver Settings
Initialization – Setting Initial Values Training Manual

• The Automatic option means that the

CFX-Solver will calculate an initial value
for the solved variable unless a previous
results file is provided
– Will be based on boundary condition
values and domain settings

• The Automatic with Value option means

that the specified value will be used
unless a previous results file is provided
– Can use a constant value or an expression

ANSYS, Inc. Proprietary Release 13.0

© 2010 ANSYS, Inc. All rights reserved. 4-5 December 2010
Solver Settings
Initialization – Using a Previous Solution Training Manual

• To use a previous solution as the

initial guess enable the Initial Values
Specification toggle when launching
the Solver
– You can provide multiple initial values
files
• When simulating a system you can
provide previous solutions for each
component of the system as the initial
guess
• Usually each file would correspond to a
separate region of space
• It is best if domains in the Solver Input
File do not overlap with multiple initial
values files

ANSYS, Inc. Proprietary Release 13.0

© 2010 ANSYS, Inc. All rights reserved. 4-6 December 2010
Solver Settings
Solver Control – Editing Training Manual

• Edit the Solver Control object in the Outline tree

ANSYS, Inc. Proprietary Release 13.0

© 2010 ANSYS, Inc. All rights reserved. 4-7 December 2010
Solver Settings
Solver Control – Options Training Manual

• The Solver Control panel contains

various controls that influence the
behavior of the solver

• These controls are important for the

accuracy of the solution, the stability of
the solver and the length of time it takes
to obtain a solution

ANSYS, Inc. Proprietary Release 13.0

© 2010 ANSYS, Inc. All rights reserved. 4-8 December 2010
Solver Settings
Solver Control – Advection Scheme Training Manual

• The Advection Scheme refers to the way the

advection term in the transport equations is
modeled numerically
– i.e. the term that accounts for bulk fluid motion
– Often the dominant term

Unsteady Advection Diffusion Generation

• Three schemes are available, High

Resolution, Upwind and Specified Blend
– Discussed in more detail next

• There is rarely any reason to change from the

default High Resolution scheme

ANSYS, Inc. Proprietary Release 13.0

© 2010 ANSYS, Inc. All rights reserved. 4-9 December 2010
Solver Settings
Solver Control – Advection Scheme Theory Training Manual

• Solution data is stored at nodes, but variable values are required

at the control volume faces to calculate fluxes

• The upstream nodal values (fup) are interpolated to the integration

points (fip) on the control volume faces using:

ip =  up +    r
– Where  is the variable gradient and ip = up +    r is the vector between the
upstream node and the integration point
– In other words, the ip value is equal to the upstream value plus a
correction due to the gradient
– b can have values between 0 and 1 …

ANSYS, Inc. Proprietary Release 13.0

© 2010 ANSYS, Inc. All rights reserved. 4-10 December 2010
Solver Settings
Solver Control – Advection Scheme Theory Training Manual

Flow is misaligned
ip =  up +    r with mesh
Theory

1
• If b = 0 we get the Upwind advection
scheme, i.e. no correction 0
– This is robust but only first order accurate
– Sometimes useful for initial runs, but
usually not necessary
Upwind Scheme
• The Specified Blend scheme allows you to
specify b between 0 and 1 (i.e. between no
correction up to full correction)
– But this is not guaranteed to be bounded,
meaning that when the correction is =1.00
included it can overshoot or undershoot
what is physically possible

• The High Resolution scheme maximizes b High Resolution

throughout the flow domain while keeping Scheme
the solution bounded
ANSYS, Inc. Proprietary Release 13.0
© 2010 ANSYS, Inc. All rights reserved. 4-11 December 2010
Solver Settings
Solver Control – Turbulence Numerics Training Manual

• Regardless of the Advection Scheme

selection, the Turbulence equations
default to the First Order (Upwind)
scheme
– Usually this is sufficient

• The High Resolution scheme can be

selected for additional accuracy
– Can give better accuracy in boundary
layers on unstructured meshes

ANSYS, Inc. Proprietary Release 13.0

© 2010 ANSYS, Inc. All rights reserved. 4-12 December 2010
Solver Settings
Solver Control – Convergence Control Training Manual

• The Solver will finish when it reaches Max.

Iterations unless convergence is achieved
sooner
– If Max. Iterations is reached you may not have
a converged solution
– Can be useful to set Max. Iterations to a large
number

• When the Solver finishes you should always

check why it finished

• Fluid Timescale Control sets the timescale in

a steady-state simulation …

ANSYS, Inc. Proprietary Release 13.0

© 2010 ANSYS, Inc. All rights reserved. 4-13 December 2010
Solver Settings
Solver Control – Timescale Background Training Manual

• ANSYS CFX employs the so called False Transient Algorithm

– A timescale is used to move the solution towards the final answer

• In a steady-state simulation the timescale provides relaxation of the

equation non-linearities

• A steady-state simulation is a “transient” evolution of the flow from the

initial guess to the steady-state conditions
– Converged solution is independent of the timescale used

Initial Guess
50 iterations
100 iterations
150 iterations

Final Solution

ANSYS, Inc. Proprietary Release 13.0

© 2010 ANSYS, Inc. All rights reserved. 4-14 December 2010
Solver Settings
Solver Control – Timescale Selection Training Manual

• For obtaining successful

convergence, the selection of the
timescale plays an important role

– If the timescale is too large, the

convergence becomes bouncy or
may even lead to the failure of the
Solver

– If the timescale is too small, the

convergence will be very slow and
the solution may not be fully
accurate

ANSYS, Inc. Proprietary Release 13.0

© 2010 ANSYS, Inc. All rights reserved. 4-15 December 2010
Solver Settings
Solver Control – Timescale Selection Training Manual

• For advection dominated flow, a fraction of the fluid residence time is

often a good estimate for the timescale
– A timescale of 1/3 of (Length Scale / Velocity Scale) is often optimal
– May need a smaller timescale for the first few iterations and for complex
physics, transonic flow,…..

• For rotating machines, 1/ ( in rad/s) is a good choice

• For buoyancy driven flows, the timescale should be based on a

function of gravity, thermal expansivity, temperature difference and
length scale (see documentation)

ANSYS, Inc. Proprietary Release 13.0

© 2010 ANSYS, Inc. All rights reserved. 4-16 December 2010
Solver Settings
Solver Control – Timescale Control Training Manual

• Timescale Control can be Auto Timescale,

Physical Timescale or Local Timescale
Factor

• Physical Timescale

– Specify the timescale. Usually a constant but

can also be variable via an expression

– Can often set a better timescale than Auto

Timescale would produce – faster
convergence

ANSYS, Inc. Proprietary Release 13.0

© 2010 ANSYS, Inc. All rights reserved. 4-17 December 2010
Solver Settings
Solver Control – Timescale Control Training Manual

• Auto Timescale
– The Solver calculates a timescale based on
boundary / initial conditions or current solution
and domain length scale

– Use a Conservative or Aggressive estimate for

the domain length scale, or a specified value

– Timescale is re-calculated and updated every

few iterations as the flow field changes

– Can set a Maximum Timescale to provide an

upper limit

– Tends to produce a conservative timescale

– Timescale factor (default = 1) is a multiplier

ANSYS, Inc. Proprietary Release 13.0
© 2010 ANSYS, Inc. All rights reserved. 4-18 December 2010
Solver Settings
Solver Control – Timescale Control Training Manual

• Local Timescale Factor

– Timescale varies throughout the domain

Local Mesh Length Scale

Local Timescale =
Local Velocity Scale

Smaller Timescale in high

velocity and/or fine mesh regions

– Can accelerate convergence when vastly different local velocity scales exist
• E.g. a jet entering a plenum
– Best used on fairly uniform meshes, since small element will have a small
timescale
© 2010 ANSYS, Inc. All rights reserved. which can slow convergence
ANSYS, Inc. Proprietary
4-19
Release 13.0
December 2010
Solver Settings
Solver Control – Convergence Criteria Training Manual

• Convergence Criteria settings determine

when the solution is considered converged
and hence when the Solver will stop
– Assuming Max. Iterations is not reached

• Residuals are a measure of how accurately

the set of equations have been solved
– Since we are iterating towards a solution, we never
get the exact solution to the equations
– Lower residuals mean a more accurate solution to
the set of equations (more on the next slide)
– Do not confuse accurately solving the equations
with overall solution accuracy – the equations may
or may not be a good representation of the true
system!
– Residuals are just one measure of accuracy and
should be combined with other measures:
• Monitor Points (ch. 8) and Imbalances (below)

ANSYS, Inc. Proprietary Release 13.0

© 2010 ANSYS, Inc. All rights reserved. 4-20 December 2010
Solver Settings
Solver Control – Residuals Theory Training Manual

• The continuous governing equations are discretized into a set of linear

equations that can be solved. The set of linear equations can be written in
the form:
[A] [Φ] = [b]

where [A] is the coefficient matrix and [Φ] is the solution variable

• If the equation were solved exactly we would have:

[A] [Φ] - [b] = [0]

• The residual vector [R] is the error in the numerical solution:

[A] [Φ] - [b] = [R]

• Since each control volume has a residual we usually look at the RMS
average or the maximum normalized residual

ANSYS, Inc. Proprietary Release 13.0

© 2010 ANSYS, Inc. All rights reserved. 4-21 December 2010
Solver Settings
Solver Control – Residuals Training Manual

• Residual Type
– MAX: Convergence based on maximum
residual anywhere
– RMS: Convergence based on average
residual from all control volumes

R i
2

– Root Mean Square = i

n

• Residual Target
– For reasonable convergence MAX residuals
should be 1.0E-3, RMS should be at least
1.0E-4
– The targets dependent on the accuracy
needed
• Lower values may be needed for greater
accuracy

ANSYS, Inc. Proprietary Release 13.0

© 2010 ANSYS, Inc. All rights reserved. 4-22 December 2010
Solver Settings
Solver Control – Conservation Target Training Manual

• The Conservation Target sets a target for the

global imbalances
Flux In  Flux Out
% Imbalance
Maximum Flux
• The imbalances measure the overall
conservation of a quantity (mass, momentum,
energy) in the entire flow domain

• Clearly in a converged solution Flux In should equal Flux Out

• It’s good practice to set a Conservation Target and/or monitor the

imbalances during the run

• When set, the Solver must meet both the Residual and Conservation Target
before stopping (assuming Max. Iterations is not reached)

• Set a target of 0.01 (1%) or less

– Flux In – Flux Out < 1%

ANSYS, Inc. Proprietary Release 13.0

© 2010 ANSYS, Inc. All rights reserved. 4-23 December 2010
Solver Settings
Solver Control – Elapsed Time and Interrupt Control Training Manual

• Elapsed Time Control

– Can specify the maximum wall clock time
for a run
– Solver will stop after this amount of time
regardless of whether it has converged

• Interrupt Control
– Can specify other criteria for stopping
the Solver based on logical CEL
expressions
– When the expression returns true the
solver will stop
• Any value >= 0.5 is true
– Examples
• If temperature exceeds a specified value
if(areaAve(T)@wall>200[C],1,0)
• If mesh quality drops below a specified value in a moving mesh case
– More on logical expressions in the CEL lecture

ANSYS, Inc. Proprietary Release 13.0

© 2010 ANSYS, Inc. All rights reserved. 4-24 December 2010
Solver Settings
Solver Control – Solid Timescale Control Training Manual

• This option is only available when a solid

domain is included in the simulation

• The Solid Timescale should be selected such

that it is MUCH larger than the fluid timescale
(100 times larger is typical)
– the energy equation is usually very stable in
the solid zone
– solid timescales are typically much larger than
fluid timescales

• The fluid timescale is estimated using Length Scale / Velocity Scale

• The solid timescale is automatically calculated as function of the length

scale, thermal conductivity, density and specific heat capacity
– Or you can choose the Physical Timescale option and provide a timescale
directly

ANSYS, Inc. Proprietary Release 13.0

© 2010 ANSYS, Inc. All rights reserved. 4-25 December 2010
Solver Settings
Solver Control – Equation Class Settings Training Manual

• The Equation Class Settings tab is an

advanced option that can be used to
set Solver controls on an equation
specific basis
– Not usually needed
– Will override the controls set on Basic
Settings for the selected equation

• Advanced Options
– Advanced solver control options
– Rarely needed

ANSYS, Inc. Proprietary Release 13.0

© 2010 ANSYS, Inc. All rights reserved. 4-26 December 2010
Solver Settings
Output Controls – Results Training Manual

• The Output Control settings control the output

produced by the Solver
– The Trn Results, Trn Stats and Export tab only apply to
transient simulations and are covered in the Transient
chapter

• The Results tab controls the final .res file

– Generally do not use the Selected Variables (or None!)
option since it probably won’t contain enough
information to restart the run later
– Output Equation Residuals is useful if you need to
check where convergence problems are occurring
– Extra Output Variables List
contains variables that are not
written to the standard results
file
• E.g. Vorticity

ANSYS, Inc. Proprietary Release 13.0

© 2010 ANSYS, Inc. All rights reserved. 4-27 December 2010
Solver Settings
Output Controls – Backup Training Manual

• The Backup tab controls if and when

backup results files are automatically
written by the Solver

• Recommend for long Solver runs in case

of power failure, network interruptions, etc

• Option:
– Standard: Like a full results file
– Essential: Allows a clean solver restart
– Smallest: Can restart the solver, but there’ll
be a jump in the residuals
– Selected Variables: Not recommended

• Can also manually request a backup file

from the Solver Manager at any time

Frequency of output can be adjusted

ANSYS, Inc. Proprietary Release 13.0

© 2010 ANSYS, Inc. All rights reserved. 4-28 December 2010
Solver Settings
Output Controls – Monitor Training Manual

• The Monitor tab allows you to create Monitor

Points
– These are used to track values of interest as
the Solver runs

• The Cartesian Coordinates Option is used to

track the value of a variable at a specific X, Y,
Z location

• The Expression Option is used to monitor the

values of a CEL expression
– E.g. Calculate the area average of Cp at the
inlet boundary: areaAve(Cp)@inlet
– E.g. Mass flow of particular fluid through an
outlet: oil.massFlow()@outlet

• In steady-state simulations you should create

monitor points for quantities of interest
– One measure of convergence is when these
values are no longer changing

ANSYS, Inc. Proprietary Release 13.0

© 2010 ANSYS, Inc. All rights reserved. 4-29 December 2010
Solver Settings
Solver Manager Training Manual

• The CFX-Solver Manager is a graphical user interface used to:

– Define a run
– Control the CFX-Solver interactively
– View information about the emerging solution
– Export data

ANSYS, Inc. Proprietary Release 13.0

© 2010 ANSYS, Inc. All rights reserved. 4-30 December 2010
Solver Settings
Solver Manager – Defining a Run Training Manual

• Define a new Solver run

• Solver Input File should be the .def file

– Can also pick .res, .bak or _full.trn files to restart a
previous incomplete run

• To make a physics change and restart a solution,

create a new .def file and provide it as the Solver
Input File then select the .res, .bak or _full.trn file
in the Initial Values Specification section
– If both files have the same physics, this is the same
as picking the .res/.bak/_full.trn file as the input file

• Use Mesh From selects which mesh to use. If the

meshes are identical can use either option,
otherwise:
– If you use the Solver Input File mesh, the Initial
Values solution is interpolated onto the input file
– If you use the Initial Values mesh only the physics
from the Solver Input File is used

• Continue History From carriers over convergence

history and iteration counters
ANSYS, Inc. Proprietary Release 13.0
© 2010 ANSYS, Inc. All rights reserved. 4-31 December 2010
Solver Settings
Solver Manager – Defining a Parallel Run Training Manual

• By default the Solver will run in serial

– A single solver process runs on the local
machine

• Set the Run Mode to one of the parallel options

to make use of multiple cores/processors
– Requires parallel licenses
– Allows you to divide a large CFD problem into
smaller partitions
• Faster solution times
• Solve larger problems by making use of memory
(RAM) on multiple machines

• The Local Parallel options should be used

when running on a single machine

• The Distributed Parallel options should be

used when running across multiple machines

ANSYS, Inc. Proprietary Release 13.0

© 2010 ANSYS, Inc. All rights reserved. 4-32 December 2010
Solver Settings
Solver Manager – Defining a Parallel Run Training Manual

• Serial

• Local Parallel

• Distributed Parallel

• Different communication methods are available (MPICH2, HP MPI, PVM)

– See documentation “When To Use MPI or PVM” for more details, but HP MPI is
recommended in most cases

ANSYS, Inc. Proprietary Release 13.0

© 2010 ANSYS, Inc. All rights reserved. 4-33 December 2010
Solver Settings
Solver Manager – Define Run Advanced Controls Training Manual

• The Show Advanced Control toggle enables the

Partitioner, Solver and Interpolator tabs

• On the Partitioner tab you can pick different

partitioning algorithms
– Partitioning is always a serial process
– Can be a problem for v.large cases since you
cannot distribute the memory load across multiple
machines
– The default MeTiS algorithm uses more memory
than others, so if you run out of memory use a
different method (see documentation for details)

• Multidomain Option:
– Independent Partitioning: Each domain is
partitioned into n partitions
– Coupled Partitioning: All domains are combined
and then partitioned into n partitions
• There’s a specific option for Transient Rotor Stator
cases

ANSYS, Inc. Proprietary Release 13.0

© 2010 ANSYS, Inc. All rights reserved. 4-34 December 2010
Solver Settings
Solver Manager – Define Run Advanced Controls Training Manual

• On the Solver tab you can select the Double

Precision option
– The solver will use more significant figures in its
calculations
– Doubles solver memory requirements
– Use when round-off error could be a problem – if
‘small’ variations in a variable are important,
where ‘small’ is relative to the global range of
that variable, e.g:
• Many Mesh Motion cases, since the motion is often
small relative to the size of the domain
• Most CHT cases, since thermal conductivity is
vastly different in the fluid and solid
• If you have a wide pressure range, but small
pressure changes are important
– Small values by themselves do not need DP

• The Solver estimates its memory requirements upfront

• Memory Alloc Factor is a multiplier for this estimate
– Use when the solver stops with an “Insufficient Memory Allocated” error

ANSYS, Inc. Proprietary Release 13.0

© 2010 ANSYS, Inc. All rights reserved. 4-35 December 2010
Solver Settings
Solver Manager – Interactive Solver Control Training Manual

• During a solution Edit Run in Progress lets you make changes on the fly
– Models generally cannot be changed, but timescales, BC’s, etc can

ANSYS, Inc. Proprietary Release 13.0

© 2010 ANSYS, Inc. All rights reserved. 4-36 December 2010
Solver Settings
Solver Manager – Additional Solution Monitors Training Manual

• By default monitor plots

New Monitor
are created showing the
RMS residuals for each
equation solved, plus one
plot for any monitor points
• Right-click to switch
between RMS and MAX
• Additional monitors can be
selected showing:
– Imbalances
– Boundary fluxes (FLOW)
– Boundary forces
• Tangential (viscous) Right-click
• Normal (pressure)
– Source terms …

Monitor Plot .out file

ANSYS, Inc. Proprietary Release 13.0

© 2010 ANSYS, Inc. All rights reserved. 4-37 December 2010
Solver Settings
Solver Manager – Additional Icons Training Manual

• By dragging the cursor over any icon, the feature

description will appear

Start a new Switch

Simulation Residual Plot
between
Monitor Stop Current RMS and
Finished Run Run MAX

Monitor Run Save Current

in Progress Run
ANSYS, Inc. Proprietary Release 13.0
© 2010 ANSYS, Inc. All rights reserved. 4-38 December 2010