Scribd
Upload
88 views43 pages

Study of Microstructure of Steels at Different Cooling Rates and Further Check Hardness of The Samples

The document discusses a study to examine the microstructure of steels cooled at different rates and check the hardness of the samples. It outlines the procedure which involves preparing 3 samples cooled at different rates (air, oil, water), observing their microstructures under a microscope, and testing their hardness. Various concepts are explained such as the TTT diagram, phases in the iron-carbon diagram, and common hardness testing techniques like Rockwell testing.

Uploaded by

Deepu Choudhary
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
88 views43 pages

Study of Microstructure of Steels at Different Cooling Rates and Further Check Hardness of The Samples

The document discusses a study to examine the microstructure of steels cooled at different rates and check the hardness of the samples. It outlines the procedure which involves preparing 3 samples cooled at different rates (air, oil, water), observing their microstructures under a microscope, and testing their hardness. Various concepts are explained such as the TTT diagram, phases in the iron-carbon diagram, and common hardness testing techniques like Rockwell testing.

Uploaded by

Deepu Choudhary
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 43

Study of microstructure

of steels at different
cooling rates and further
check hardness of the
samples
Equipment and Apparatus
required
1. Microscope
2. Oil bath
3. Emery papers Grit size (refer students general guidelines)
4. Diamond paste 6 microns, 1 micron diameter
5. Disc Polishing machine,
6. Inverted Optical Microscope
7. Drier
Steel
Steel is the world's most important engineering and
construction material.

It is used in every aspect of our lives; in cars and


construction products, refrigerators and washing machines,
cargo ships and surgical scalpels.

It can be recycled over and over again without loss of


property.
Steel is not a single product. There are more than 3,500
different grades of steel with many different physical,
chemical, and environmental properties.

Approximately 75% of modern steels have been developed


in the past 20 years. If the Eiffel Tower were to be rebuilt
today, the engineers would only need one-third of the steel
that was originally used.

Modern cars are built with new steels that are stronger but
up to 35% lighter than in the past.
Emery papers

Emery is rated on the average grit size, glued to the backing.

Common sizes are, from coarse to fine: 40, 46, 54, 60, 70,
80, 90, 100, 120, 180, 220, 320, F, and FF. A 46 or 54 grade
cloth is used on roughly filed work, while 220 to 320 grit
cloth will give a good polish
Diamond Paste For
Polishing/Lapping/Grinding.
Polishing is finishing processes for smoothing a
workpiece's surface using an abrasive and a work
wheel or a leather strop.

Technically polishing refers to processes that use


an abrasive that is glued to the work wheel,
while buffing uses a loose abrasive applied to the
work wheel
Polishing Machine
Polishing is often used to enhance the appearance of an
item, prevent contamination of instruments, remove
oxidation, create a reflective surface, or prevent
corrosion in pipes.

In metallography and metallurgy, polishing is used to


create a flat, defect-free surface for examination of a
metal's microstructure under a microscope.

Silicon-based polishing pads or a diamond solution can


be used in the polishing process. 
Inverted Microscope
Austenitizing temperature

The temperature at which the steel and ferrous alloys are


heated above their critical temperatures is called the
austenitizing temperature.

Generally the austenitizing temperature ranges from 400°C


(752°F) to 800°C (1472°F) for different grades of carbon,
alloys and tool steels.
Iron Carbon Diagram
Alloy metals can exist in different phases. Phases are physically
homogeneous states of an alloy. A phase has a precise chemical
composition – a certain arrangement and bonding between the atoms.

This structure of atoms imparts different properties to different phases.


We can choose the phase we want and use it in our applications.
Phase diagrams
Phase diagrams are graphical representations of
the phases present in an alloy at different
conditions of temperature, pressure, or chemical
composition.
Example
The diagram describes the suitable conditions for two or
more phases to exist in equilibrium.

For example, the water phase diagram describes a point


(triple point) where water can coexist in three different
phases at the same time.

This happens at just above the freezing temperature


(0.01°C) and 0.006 atm.
There are four major uses of alloy
phase diagrams

Development of new alloys based on application


requirements.
Production of these alloys.
Development and control of appropriate heat treatment
procedures to improve the chemical, physical, and
mechanical properties of these new alloys.

Troubleshooting problems that arise in application of these


new alloys, ultimately improving product predictability.
Iron-carbon phase diagram
The iron-carbon phase diagram is widely used to
understand the different phases of steel and cast iron. Both
steel and cast iron are a mix of iron and carbon. Also, both
alloys contain a small amount of trace elements.
This iron carbon phase diagram is plotted with the
carbon concentrations by weight on the X-axis and
the temperature scale on the Y-axis.
The carbon in iron is an interstitial impurity.
The alloy may form a face centred
cubic (FCC) lattice or a body centred
cubic (BCC) lattice. It will form a solid
solution with α, γ, and δ phases of iron.
The weight percentage scale on the X-axis of the
iron carbon phase diagram goes from 0% up to
6.67% Carbon. Up to a maximum carbon content of
0.008% weight of Carbon, the metal is simply called
iron or pure iron.

It exists in the α-ferrite form at room temperature.


From 0.008% up to 2.14% carbon content, the iron
carbon alloy is called steel.

Within this range, there are different grades of


steel known as low carbon steel (or mild steel),
medium carbon steel, and high carbon steel.
When the carbon content increases beyond
2.14%, we reach the stage of cast iron.

Cast iron is very hard but its brittleness


severely limits its applications and methods
for forming.
Eutectic Point

Eutectic point is a point where multiple phases meet. For


the iron-carbon alloy diagram, the eutectic point is where
the lines A1, A3 and ACM meet. The formation of these
points is coincidental.
At these points, eutectic reactions take place where
a liquid phase freezes into a mixture of two solid
phases.

This happens when cooling a liquid alloy of eutectic


composition all the way to its eutectic temperature.
The alloys formed at this point are known as
eutectic alloys.

On the left and right side of this point, alloys are


known as hypoeutectic and hypereutectic alloys
respectively
(‘hypo’ in Greek means less than, ‘hyper’ means greater than).
Different Phases
α-ferrite

Existing at low temperatures and low carbon


content, α-ferrite is a solid solution of carbon in
BCC Fe.

This phase is stable at room temperature. In the


graph, it can be seen as a sliver on the left edge
with Y-axis on the left side and A2 on the right.
This phase is magnetic below 768°C.
It has a maximum carbon content of 0.022 % and it
will transform to γ-austenite at 912°C as shown in
the graph.
γ-austenite

This phase is a solid solution of carbon in FCC Fe with a


maximum solubility of 2.14% C.

On further heating, it converts into BCC δ-ferrite at


1395°C.

γ-austenite is unstable at temperatures below eutectic


temperature (727°C) unless cooled rapidly. This phase
is non-magnetic.
δ-ferrite

This phase has a similar structure as that of α-


ferrite but exists only at high temperatures.

The phase can be spotted at the top left corner in


the graph. It has a melting point of 1538°C.
Fe3C or cementite

Cementite is a metastable phase of this alloy with a fixed


composition of Fe3C. It decomposes extremely slowly at
room temperature into Iron and carbon (graphite).
TTT diagram
Isothermal transformation diagrams (also known as time-temperature-
transformation (TTT) diagrams)

TTT-diagrams are plots of temperature versus time (usually on a logarithmic


scale)

Transformation products vary depending on the cooling rate.


TTT
Theory
If specimen is rapidly quenched from austenizing
temperature a very hard phase martensite is formed, while
very slow cooling results in formation of pearlite which is
the softest phase.

If rate of cooling is kept moderate it results in formation of


bainite phase whose hardness is intermediate to that of
martensite and pearlite.
Outline of the Procedure
Sample Preparation
Three samples to be cooled by following different
cooling rates are prepared by using standard
metallographic technique
Observation
Normal Hardness
Hardness in air cooled sample
Hardness in oil cooled sample
Hardness in Water cooled sample.
Hardness testing machines
Hardness testing machines perform three common kinds of
scientific hardness tests:

the Brinell hardness test, the Rockwell hardness test, and


the Vickers hardness test.

The Rockwell hardness test is the most widely used


technique, easy to carry out and more precise than other
kinds of evaluations.
Rockwell hardness testing
M/C

You might also like