0% found this document useful (0 votes)
135 views16 pages

A/D & D/A Converters

This document discusses analog to digital and digital to analog converters. It covers resolution, conversion processes, types of DACs including binary weighted resistor, R-2R ladder, and inverted R-2R ladder DACs. Types of ADCs discussed include flash, counter, successive approximation, and dual slope converters. Key components and conversion principles of each are summarized.

Uploaded by

geet_batta
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
135 views16 pages

A/D & D/A Converters

This document discusses analog to digital and digital to analog converters. It covers resolution, conversion processes, types of DACs including binary weighted resistor, R-2R ladder, and inverted R-2R ladder DACs. Types of ADCs discussed include flash, counter, successive approximation, and dual slope converters. Key components and conversion principles of each are summarized.

Uploaded by

geet_batta
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
You are on page 1/ 16

A/D & D/A Converters

DAC Fundamentals
Resolution
• Resolution is defined as the ratio of change in
analog output voltage resulting from a change
of 1 LSB at the digital input.
Resolution =VFS/2n-1
Where n= number of digital inputs
• The full scale analog output voltage VFS is
defined as the output voltage corresponding
to the digital input with all digits 1.
D to A conversion
• The basic building blocks of a DAC are-
a resistive n/w
digitally controlled electronic switches
a voltage reference
current to voltage converter
Types of DAC
• Binary weighted resistor
• R-2R ladder DAC
• Inverted R-2R ladder DAC
Binary Weighted Resistor DAC
• Binary weighted resistor uses a network of binary
weighted resistors and a summing amplifier .There 2n
resistors and n number of SPDT(single pole double
throw) type switches.
• The position of the moving arm of every switch is
controlled by the binary input word.
• The n bit digital word decide the positions of all the
SPDT switches and connect their corresponding
binary weighted resistors to either ground or -VR
R-2R Ladder DAC
• The problem of using wide range of resistor
values can be solved by using R-2R ladder
type DAC.
• There are only two values of resistors are
required.
• R-2R provide results accurately.
• We can also increase the number of bits by
adding more sections of R/2R values.
Inverted R-2R Ladder DAC
• It is also known as current mode R-2R ladder
DAC because this circuit operates on the
current.
• It is called as inverted because the positions of
MSB and LSB in the original R-2R ladder DAC
have been interchanged.
Analog to Digital conversion
1. Sampling
2. Holding
3. Quantizing
4. Encoding
A to D Converter
• ADC performs a function which is exactly opposite
to that of a DAC . The input to an ADC is the analog
voltage VA and at the output is n bit digital word.
• In n bit digital output d1 represent MSB and dn is
the LSB.The analog input voltage VA produces an
output digital word having a function value D .
D=d12-1 +d22-2+……..+dn2-n
A to D(Contd.)
• ADC block has a reference voltage VR input
and control lines SOC and EOC .SOC is used to
start the A to D conversion whereas EOC
output goes high to indicate that the
conversion is complete.
Types of A to D converters
• Flash type
• Counter type
• Successive approximation
• Dual slope
Flash type or Parallel type ADC
• The parallel comparator uses a number OP-AMP
comparators.
• A 2 bit parallel comparator having
i. The non inverting(+) terminal that has been connected
to analog input
ii. The inverting(-) terminal that has been connected to a
different reference voltage. i.e. v1, v2 and v3 and
these voltage are derived from voltage source VR
.There are three comparators C1, C2 and C3 and a
priority encoder
2 bit flash type

Range Analog input Comparators o/p Encoder o/p


number voltage (VA ) C3 C2 C1 Y1 Y0
1. 0<VA<VR/4 0 0 0 0 0
2. VR/4<VA<VR/2 0 0 1 0 1
3. VR/2<VA<3VR/4 0 1 1 1 0
4. 3VR/4<VA<VR 1 1 1 1 1
Successive approximation ADC
• The successive approximation receives the
comparator output ,clock and SOC and
produces an n-bit digital output along with the
end of conversion .When SOC initiates then
SAR will set the MSB d1=1 with all bits 0.So
the trial code becomes 1000 0000 for an 8-bit
ADC . This trial code is then applied at the
input of a DAC.The corresponding output of
DAC VD is applied to comparator.
Dual slope integrator ADC
• In this ADC, an unknown analog voltage and a
known reference voltage are converted into
equivalent time periods using an integrator.
These time periods are measured by a
counter. This circuit is known as dual slope
ADC because the analog voltage and the
reference voltage are converted to ramp
signals of different slopes by the integrator.

You might also like