Scribd
Upload
26 views

Lecture 1 - Power Systems Overview

The document provides an overview of electrical power systems, including their main components and objectives of delivering reliable power. It describes the general composition and functions of key parts: generation, transmission, distribution, and utilization. Power is generated mostly by synchronous generators, transmitted via high-voltage lines, stepped down for distribution, and then utilized by industrial, commercial and residential customers. Quality of supply and meeting demand are important objectives.

Uploaded by

Syed Munawar
Copyright
© © All Rights Reserved
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
26 views

Lecture 1 - Power Systems Overview

The document provides an overview of electrical power systems, including their main components and objectives of delivering reliable power. It describes the general composition and functions of key parts: generation, transmission, distribution, and utilization. Power is generated mostly by synchronous generators, transmitted via high-voltage lines, stepped down for distribution, and then utilized by industrial, commercial and residential customers. Quality of supply and meeting demand are important objectives.

Uploaded by

Syed Munawar
Copyright
© © All Rights Reserved
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
You are on page 1/ 13

Electrical Power Systems

– An Overview

Dr. Muhammad Asghar Saqib


1.1 INTRODUCTION
• The main components of a power system:
Generators, transformers, transmission lines, load, and protection
and control equipment.
• Interconnected power system: generation is generally far away for
load centres.
• Electrical power can be very efficiently transmitted over very large
distances.
• Delivery of good-quality electrical energy at competitive prices is
the objective.
• The measure of the Quality of Electrical Supply in terms of:
Constant voltage magnitude, e.g. no voltage sags (lower than
the rated voltage) or swells (higher voltages)
Constant frequency
Higher power factor (will be explained later)
Balanced phases
Sinusoidal waveforms, e.g. no harmonic content
Lack of interruptions 2
Ability of withstand faults and recover quickly.
1.2 General Composition of a Power Network
• For most practical purposes a power network maybe divided
into Generation, transmission, distribution and utilization (see
Figure).
Generation

Switch Yard/Substation

Power Plant
500 kV Transmission Line Primary Grid
(11-30 kV/500 kV)
(500/132 kV)

Commercial/ 132 kV
Industrial SubTransmission Line
Customer

Distribution Transformer
Urban (11/0.415 kV) Primary Distribution Line
Customers

Secondary Grid
Secondary Distribution (132/11 kV)
Distribution
Underground Cable
Pole
To Other
Residential Residential 132 kV
Customer Substations
Customer
3
1.2 General Composition of a Power Network Continued

4
1.2.1 Power Generation
•Generation is generally far away from load centres.
•Different primary energy resources to stabilize pricing mechanism.
•Most of the electricity consumed worldwide is generated by three-
phase synchronous generators.
•In future with increased wind power generation asynchronous
induction generators will also be abundant.
•Fuel cells and photovoltaics will also contribute significantly in future.
•A synchronous generator has two parts; stator and rotor.
•Rotor, under steady-state conditions, rotates at synchronous speed.
•Synchronous machines are of two kinds:
 Salient-pole machines
 Round-rotor machines
•Steam turbine driven generators work at high speeds and have round
rotors.
•The rotor carries DC field winding.
•Hydro units work at low speed at have salient-pole rotors.
•Salient-pole rotors have damper windings besides field windings.
•Damper windings consist of bars, put in slots, on pole faces and 5
connected together at both ends.
1.2.1 Power Generation Continued

6
1.2.1 Power Generation Continued

•Quadrature (q-) axis is located 90 degrees behind d-axis.


•In general, three main control systems affect the turbine-generator
set:
 The boiler’s firing angle control
 The governor control
 The excitation system control.

Main controls of a generating unit


•The excitation system consists of an exciter and the AVR, automatic
voltage regulator.
7
1.2.1 Power Generation Continued
•AVR controls the generator’s terminal voltage by controlling the
current in the field winding supplied by the exciter.
•Measured terminal voltage and desired voltage are compared to
produce error, which is used to change the exciter’s output.
•Exciters are either rotating or static.
•Static ones are preferred these days due to their fast dynamic
response and smaller response.
•Static exciters use thyristor rectifiers to adjust the field current.

8
1.2.2 Power Transmission
•Transmission of large blocks of energy at high voltages is more
efficient.
•Transmission voltages in Pakistan are 500 kV and 220 kV.
•132 kV, in Pakistan, is generally called sub-transmission voltage.
 Lines operating at 132 kV are known as sub-transmission lines.
•Step-up transformers in generating substations are used to increase
the voltage to transmission voltages.
•Step-down transformers, in distribution substations, are used to
decrease the voltages to manageable levels such as 11 kV or 66 kV.
•High voltage transmission is mostly AC overhead lines.
•DC overhead transmission lines are increasing being used to
increase the stability of power systems or for inter-connections
between different countries.
•Transmission lines are usually meshed to increase the reliability of
power (see Figure).
•Overhead transmission lines maybe double circuit lines (see Figure).
•Transmission lines used bundled ACSR (aluminium conductor steel
reinforced) conductors. 9
1.2.2 Power Transmission Continued
 Bundled conductors, with increased diameter, reduces inductance
of a transmission line.
 Corona power loss also decreases due to lower potential gradients.
• One or two sky wires are used to provide protection against
lightning.
• Underground cables are used in areas where overhead
transmission lines are impractical.

10
1.2.2 Power Transmission Continued

11
1.2.3 Power Distribution

•Distribution may either be radial or mesh/loop.


•Radial system are simple, less costly but also less reliable.
•Primary distribution in Pakistan is 11 kV: distribution transformers are
11 kV delta/415 V wye (240 V; line to grounded neutral).

12
1.2.4 Power Utilization

•Customers of electricity venders maybe classified as industrial,


commercial and domestic.
•In industrialized societies the first group may account for 2/5th of the
total demand.
•Some loads draw constant current from a power system and their
operation is affected by the variation of voltage and frequency.
•Such loads are induction motors, synchronous motors, DC motors.
•Other types of loads are less susceptible to variations in voltage and
frequency and exhibit constant-resistance characteristics.
•Some end-user loads can generate significant harmonic currents into
the system. The examples of such loads are: colour TV sets,
microwave ovens, energy-saving lamps, computer equipment,
industrial variable speed motor drives, battery recharging stations.
• For industrial applications, except for pumped hydro storage there is
little storage in the system.
•The generation must meet the demand and system’s losses.
•Load shedding may be used as last resort. 13

You might also like