Scribd
Upload
385 views36 pages

Secondary Storage Devices

Databases are typically too large to fit entirely in main memory, so they are stored in secondary storage devices like disks and tapes. Disks are better than tapes for databases because data can be accessed directly from disks at any time, while tapes require loading before access. Hard disks are the most widely used secondary storage due to their high capacity and ability to access data online without delays.

Uploaded by

VinayKumarSingh
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPT or read online on Scribd
385 views36 pages

Secondary Storage Devices

Databases are typically too large to fit entirely in main memory, so they are stored in secondary storage devices like disks and tapes. Disks are better than tapes for databases because data can be accessed directly from disks at any time, while tapes require loading before access. Hard disks are the most widely used secondary storage due to their high capacity and ability to access data online without delays.

Uploaded by

VinayKumarSingh
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPT or read online on Scribd
You are on page 1/ 36

Secondary

storage devices

SREELAJ C
ROLL NO 52
Storage of databases
 Databases typically store large amount of data.
 Generally databases are too large to fit entirely
in the main memory.
 Storage of database in secondary storage
devices such as disks prevent permanent data
loss from volatile memory (main memory).
 Cost of storage per unit data less than that of
primary memory.
Typical devices
 Magnetic tapes
 Optical disks
 Hard disks
Magnetic
Tapes
Hard disk drive
Accessing methods
 Data stored on tapes is offline since loading of
tape is needed before the data becomes
available-by an operator or a loading device
 Disks are online devices that can be accessed
directly at any time.
 Due to these factors disks are most widely
used as secondary storage devices of
DATABASE MAMAGEMENT SYSTEMS
DISK DEVICES
 Magnetic disks are used for storing data
 By magnetizing an area on a disk one can
make it represent a bit value of one or zero
 capacity of the disk is the number of bytes it
can store
 Usually the capacity of disks are too large.
 Floppies can contain 400KB to 1.44Mb
 Hard disks can accommodate hundreds of GBs
 Disks are all made of magnetic material
shaped as thin circular disk and protected by a
plastic or acrylic cover
 A disk is single sided if it stores information
only on one of its surfaces

 A disk is double sided if both surfaces are used


 To increase storage capacity disks are
assembled into a disk pack which may include
many disks and hence many surfaces.

1998 Seagate Technologies


A HARD DISK FROM IBM AT 1996
 Data is stored on a disk surface in concentric
circles of small width-each having a distinct
diameter.

 Each circle is called a track

 For disk packs the tracks with same diameter


on various surfaces are called a cylinder
because the shape they would form if
connected in space
• Number of tracks on disk ranges from few
hundred to a few thousand
• Each track typically ranges from tens of
KB to 150KB
• Because a track usually contains large
amount of information, it is divided in to
smaller blocks called sectors.
• The division of a track into sectors is hard
coded on the disk surface and cannot be
changed.
 One type of sector organization is a portion of
a track that subtends a fixed angle at the center
of a sector.

 A technique called zone bit recording allows a


range of cylinders to have the same number of
sectors per arc.

 Sectors maintaining a uniform recording


density is also possible. Then the number of
sectors will be different in each track to
preserve the density.
Formatting
 The division of a track into equal sized blocks
is set by the operating system during the disk
formatting process.

 Block size is fixed during formatting and


cannot be changed dynamically
 Typical block size: 512 to 4096 bytes
 A disk with hard coded sectors often has the
sectors subdivided into blocks during
formatting.
 Blocks are separated by fixed size inter block
gaps which include coded control information
that gives the identification of the block after
that gap.
 A disk is a random addressable device.
 Transfer of data between main memory and
disk takes place in blocks.
 Hardware address of a block is a
combination of
4. Cylinder number
5. Track number
6. Block Number
 In modern disk drives LBA is used.
 Buffer is the interface storage area between
disk drive mechanism and main memory.
 Read operation
 Write operation
 Cluster is several contiguous blocks.
Hardware mechanism

 Read/write head reads a block


 Read/write head is attached to a mechanical arm.
 Disk packs with multiple disks are controlled
by several read/write heads.
 All arms are connected to an actuator attached
to another electrical motor that positions the
head.
 Disks with fixed read/write heads with as
many as heads as are called fixed-head disks.
 Disk units with an actuator are called
movable-head disks.
 Disk controller is usually embedded in disk
drive.
 SCSI-one of the std. interface for disk drives.
 Seek time- time required to position the head
on correct track. [ typical 3to8ms]
 Latency-time required for the desired block to
rotate into position
 Block transfer time-time to transfer a block of
data
 Total time needed to locate and transfer an
arbitrary block is the sum of these times.
Magnetic Tape Storage Devices
 Magnetic tapes are sequential access devices
 Data is stored on reels of high capacity
magnetic tape
 A tape drive is required to drive the tape reel
 A read/write head is used to read or write data
on tape.
 Data records are stored as blocks
 Typical data densities are 1600 to 6250 bytes
per inch
 Inter block gap of .6 inches corresponds to 960
to 3750 bytes of wasted storage.
 To get a block on the middle of the tape, entire
tape is to be scanned and until the required
block gets under the head.
 Tape access is slow and therefore not used
store online data.
 Tapes have the important function of backing
up the database.
 One reason for tape back up is to keep the data
in case of a disk crash
 Disk crash can happen if the read write head
touches the surface because of mechanical
malfunction
 Tapes can also be used to store excessively
large databases.
 Outdated, but need to be kept records are
usually stored on tape drives.
 Different capacity tape drives are available.

 Digital and super digital linear tapes having


capacities of hundreds of GBs that record data
on linear tracks are also used.
 Robotic arms are used to write multiple
catridges in parallel using multiple tape drives
with automatic labeling to identify backup.

You might also like