Ce233 Powerpoint

1
VENTURI METER
2
BASIC TERMS
• Velocity of fluid which passes through a
Flow Rate(v) given area per second (m/s).
Volumetric Flow • Volume of the fluid travelled through

a cross sectional area per second
Rate(Q) (m3/s).
• Shape of path of the fluid.

Conduit
• point in a fluid stream where the

Vena Contracta diameter of the stream is the least,
and fluid velocity is at its maximum.
4
WHAT IS VENTURIMETER?
Venturimeter device used for

measuring the rate of flow of a fluid flowing
through a pipe.It can be horizontal inclined
or vertical. In our lab we have 2 pipes one
Of 20mm and other of 25mm.
It consist of three parts,

•Converging part=20-22degrees
•Throat
•Diverging part=5-7degrees
6
WORKING PRINCIPLE
Venturi meter works under the principle of
Bernoulli's equation(energy equation) and Continuity
equation.
FIG-1 IITB
10
ASSUMPTIONS
Incompressible fluids
Frictionless inner surfaces
Steady and irrotational flow

11
EXPRESSION FOR RATE OF FLOW
•B(m2,ρ2,p2,v2)
•A(m1,ρ1,p1,v1)
Z2
Z1
Datum
At pt:-A At pt:-B
P.E = g.z1 P.E = g.z2
V.E = ½ v12 V.E = ½ v22
Pre.E = P1/ρ Pre.E = P2/ρ

12
Energy equation (horizontal arrangement)

g(Z1-Z2)+1/2(V12+V22)=(P2-P1)/ρ
If Z1=Z2
½(v12-v22)= (P2-P1)/ρ ----- (1)
As per law at continuity
A1V1=A2V2 (since density is constant)
V1=(A2/A1)V2 & V2=(A1/A2)V1
Sub V1 value in (1)
½[(A2/A1)*V22-V22]=∆P/ρ
V22=(A1 /A2 -A1 ) * 2∆P/ρ
2 2 2
13
Q2=A2.V2= A1.A2 * √2∆P/ρ

(√A22-A12)
Q α √2∆P
Theoretical-- Q2=M.√(2∆Pg)/ω
Original-- Q2=CdE M√(2∆P)/ρ
M- velocity approach factor

Q-over all volumetric flow rate
Cd-coefficient of discharge
E- thermal expansion factor
14
Q2 in terms of specific weight
Q=
Hm=manometric head in
terms of water

Hm=hg
15
VENTURI METER V/S FLOW
When a venturimeter is placed in a pipe carrying the fluid whose

flow rate is to be measured, a pressure drop occurs between the
entrance and throat of the venturimeter. This pressure drop is
measured using a differential pressure sensor and when
calibrated this pressure drop becomes a measure of flow rate.
16
CONSTRUCTION
The entry of the venture is cylindrical in shape to match the size of
the pipe through which fluid flows. This enables the venture to be
fitted to the pipe.
After the entry, there is a converging conical section with an
included angle of 19’ to 22’.
Following the converging section, there is a cylindrical section
with minimum area called as the throat.
After the throat, there is a diverging conical section with an
included angle of 5’ to 7’.
Openings are provided at the entry and throat of the venturi meter
for attaching a differential manometer.
17
MANOMETER
The differential pressure sensor used here is
Manometer.
Manometer is a device to measure pressure.
A common simple manometer consists of a U shaped
tube of glass filled with some liquid.
Manometers measure a pressure difference by
balancing the weight of a fluid column between the two
pressures of interest. Large pressure differences are
measured with heavy fluids, such as mercury (high
density).
Small pressure differences, such as those experienced in
experimental wind tunnels or venturi flowmeters are
measured by lighter fluids such as water .
19
OPERATIO
N
The fluid whose flow rate is to be measured enters the entry
section of the venturi meter with a pressure P1.
As the fluid flows into the converging section, its pressure

keeps on reducing and attains a minimum value P2 when it
enters the throat. That is, in the throat, the fluid pressure P2
will be minimum.
20
The Manometer attached between the entry and throat section of

the venturi meter records the pressure difference(P1-P2) which
becomes an indication of the flow rate of the fluid through the
pipe when calibrated.
The diverging section has been provided to enable the fluid to

regain its pressure and hence its kinetic energy. Lesser the angle
of the diverging section, greater is the
recovery.
Observation table
.
22
SAMPLE PROBLEM
A horizontal venturimeter with 15 cm inlet . 7.5 cm throat is used for

measurement of flow of water .The differential pressure between inlet
and throat is 17.5 cm, when measured using U-TUBE manometer. Make
the calculations for the water flow rate where Cd for venturi is 0.97.
Specific gravity =13.6.
Sol: Q2= Cd . M . A2 √2g{ hm [(ρm/ρ )-1]}
M=A1/√A12-A22
A1=π*d2/4=π*152/4=176.71 ,
A2=π*d2/4=π*7.52/4=44.178 M= 1.03
Q2=0.97 * 1.03* 44.178 √2*9.8*17.5(13.6-1)

=0.02901 m3/sec
IMAGE
25
ADVANTAGES
• Less chances of getting clogged with

1 sediments.
• Coefficient of discharge is high.

2
• Its behaviour can be predicted
3 perfectly.
• Can be installed vertically,

4 horizontally or inclinded.
26
DISADVANTAGES
• Highly expensive
1
• Occupies considerable space

2
QUESTIONS?
Mail id Whatsapp for doubt
[email protected] 7827896229

Ce233 Powerpoint

Uploaded by

Copyright:

Available Formats

Ce233 Powerpoint

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Ce233 Powerpoint

Uploaded by

Copyright:

Available Formats

1

Volumetric Flow • Volume of the fluid travelled through

• Shape of path of the fluid.

• point in a fluid stream where the

Venturimeter device used for

It consist of three parts,

Frictionless inner surfaces

Steady and irrotational flow

EXPRESSION FOR RATE OF FLOW

P.E = g.z1 P.E = g.z2

V.E = ½ v12 V.E = ½ v22

Pre.E = P1/ρ Pre.E = P2/ρ

Energy equation (horizontal arrangement)

A1V1=A2V2 (since density is constant)

V1=(A2/A1)V2 & V2=(A1/A2)V1

Sub V1 value in (1)

Q2=A2.V2= A1.A2 * √2∆P/ρ

Original-- Q2=CdE M√(2∆P)/ρ

M- velocity approach factor

Q2 in terms of specific weight

VENTURI METER V/S FLOW

When a venturimeter is placed in a pipe carrying the fluid whose

As the fluid flows into the converging section, its pressure

The Manometer attached between the entry and throat section of

The diverging section has been provided to enable the fluid to

A horizontal venturimeter with 15 cm inlet . 7.5 cm throat is used for

Sol: Q2= Cd . M . A2 √2g{ hm [(ρm/ρ )-1]}

Q2=0.97 * 1.03* 44.178 √2*9.8*17.5(13.6-1)

• Less chances of getting clogged with

• Coefficient of discharge is high.

• Can be installed vertically,

• Occupies considerable space

You might also like

Q2=0.97 * 1.03* 44.178 √29.817.5(13.6-1)