Introduction To AD and DA

Introduction to AD and DA
 What are AD/DA Converters

 What are they used for
 Why do you need to know how they work
 Digital coding methods

 Waveform digitising
What are AD/DA
Converters (1)
 An Analog to Digital converter [AD or ADC]

is an electronic circuit which accepts an
analog input signal (usually a voltage) and
produces a corresponding digital number at
the output
 An Digital to Analog converter [DA or DAC]
is an electronic circuit which accepts a
digital number at its input and produces a
corresponding analog signal (usually a
voltage) at the output
 They exist as modules, ICs, or fully
integrated inside other parts, e.g. µCs
What are AD/DA Converters (2)
Analog Digital Analog

continuous time world discrete time world continuous time world
+/-10v
The Real World
The Real World

+/-10v
ADC 1 DAC 1
12 16
COMPUTER
or µP/µC
+/-5v
ADC 2
16
Typical AD & DA Application

What are they used for
 Any time a real world analog signal is

connected to a digital system
 CD players, GSMs, DVMs, Digital Camcorders
etc, etc
 CERN control systems & instruments
 HOWEVER, each application has particular
needs
 Resolution - number of bits
 Speed and Accuracy
 Level of input/output waveforms
 Cost etc
Why do you need to know
how they work
 Because the theoretical course you will
shortly undertake assumes perfect
converter products - BUT
 Practical converters have :
 Many conversion methods - why
 Trade-offs between resolution and speeds +
delays
 Different methods of “sampling” the
waveforms
 A large number of basic and method-dependent
error sources
 Manufacturers specifications which ‘differ’ -
AND
 Almost all converters need some analog ‘signal
conditioning’ which is application dependent
Digital coding methods (1)
AD/DA Transfer Characteristic
 8,10,12,14,16,18, 20-24bits?
 Most/Least significant bit +10v
MSB/LSB
 Uni-polar, bipolar, straight
binary, 2’s complement -
invert MSB
 Parallel I/O or serial [delay]
0v
 Bytes or words
 Double buffering
 Digital ‘breakthrough’
 Digital correction methods
 Time skewing & jitter
-10v
0000 8000 FFFF
0000 7FFF
8000 FFFF
Digital coding methods (2)
 Resolution = 2n-1 [n = number of bits]
n 2n 1bit ppm [1x10-6]

 8bits 256 3906
 10bits 1024 976
 12bits 4096 244
 14bits 16384 61
 16bits 65536 15
 18bits 262144 3.8
 20bits 1,048576 0.95
 22bits 4,194304 0.24
 24bits 16,777216 0.06
Digital value
Waveform digitising (1)
time
 A waveform is ‘digitised’ (sampled) at a constant

rate D t
 Each such sample represents the instantaneous
amplitude at the instant of sampling
 Between samples the value remains constant [zero
order hold]
 What errors can occur in this process ?
Waveform digitising (2)
A C
D
B
 A & B show aliasing in the time domain

 C & D show a different case in the frequency
domain
- it is important to understand these effects
Waveform digitising errors
 For a DAC
 output waveform is a ‘distorted’ version of original
 higher frequencies not reproduced - aliasing ?
 ‘average shape’ displaced in time
 ‘sharp’ edges need filtering
 For an ADC
 converter sampling errors
 with a ‘sample & hold’ circuit ahead of the converter?
 integrating action during part, or all of the sample-time
?
 conversion time
 data ‘available’ delay
 aliasing - [ is multiplication of input spectrum and fs]
…[must ‘remove’ all spectrum > fs/2 before
sampling]
Sampling rate
 Nyquist rate = 2x highest frequency of

interest
 Practically, - always sample at least 5x, or
higher
 Ensure ADCs have input filtering [anti-alias]
where necessary [large hf signals]
 Filter DAC outputs to remove higher
frequencies and switching ‘glitches’
 ‘Over-sampling’ converters sample x4 to
x500 - this may reduce above problems
and/or extend resolution
Understanding Conversion
Methods
AD/DA Methods
 Some very simple ideas

 DAC circuits
 Basic ADC circuits
 Successive approximation, flash - S&H
 Integrating - single/dual/multi slope
 Charge balance, 
Some very simple ideas
‘Digitally set’
Comparator
potentiometer
DAC ADC
Vref
dial Unknown
voltage
Vdac equal
=
 ADC =
 precise reference voltage
 comparison of divider value with unknown [analog input]
 “digitally adjustable” divider or potentiometer [output
value]
 DAC =
 precise reference voltage ……. {multiplying dac}
 “digitally adjustable” divider or potentiometer [input
value]
 optional output amplifier of pot. value [analog output]
DAC circuits (1)
Simplified binary weighted resistor DAC R - 2R ladder DAC
8.75V
9.375
max.
 Summation of binary weighted currents

 Modern DACs use the ‘R-2R ladder’
DAC circuits (2)
 Important circuit concepts
 Resistor tracking - temp. & time > ratios
 Switch is part of R [on & off resistance]
 Limits for tracking and adjustment
 Switch transition times - glitches
 Switched current sources are faster
 Other DAC methods
 DC performance not needed for all uses
 Different ladders, Caps. as well as Resistors
 PWM, F>V
 Sigma-Delta
 Performance cannot be better than the Reference
- {multiplying DAC concept}
ADC methods
 Ramp-compare ADC
 Flash ADC (direct-conversion)
 Successive approximation
 Integrating ADC
 Delta-encoded
 Pipelined
 Sigma-delta
 …
Ramp-compare ADC
Basic ADC circuits (1)
Simple ramp-compare ADC
Unknown
analog
input
start Binary output
 Digitising begins with a ‘start’ pulse

 DAC is ramped up from zero
 counter stopped by comparator when Vin = DAC out
 ADC output is counter value
 Tracking ADC
Basic ADC circuits (2)
 This ADC circuit is limited and rarely used
WHY -
 slow
 variable time to give result
 input signal can vary during digitising
 Successive Approximation ADC solves these

problems - using
 complex logic to test and retain each DAC bit
 a sample and hold circuit ahead of the
comparator
Successive Approximation ADC
Successive Approximation ADC
 Fast process - 1 -
100µsecs
 Result always n clocks

after start
 Used extensively for

12-16bit DAQ systems
Flash ADC
Vref
Flash
Flash ADC
Vref
Half-Flash
analog
input
analog
 The fastest process <50nsecs input
 Limited resolution typically 8 -
10bits
 Half-flash technique is cheaper

Introduction To AD and DA

Uploaded by

Copyright:

Available Formats

Introduction To AD and DA

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Introduction To AD and DA

Uploaded by

Copyright:

Available Formats

Introduction to AD and DA

 What are AD/DA Converters

 Digital coding methods

 An Analog to Digital converter [AD or ADC]

Analog Digital Analog

The Real World

Typical AD & DA Application

 Any time a real world analog signal is

 Resolution = 2n-1 [n = number of bits]

n 2n 1bit ppm [1x10-6]

 A waveform is ‘digitised’ (sampled) at a constant

 A & B show aliasing in the time domain

 Nyquist rate = 2x highest frequency of

 Some very simple ideas

Simplified binary weighted resistor DAC R - 2R ladder DAC

 Summation of binary weighted currents

Simple ramp-compare ADC

start Binary output

 Digitising begins with a ‘start’ pulse

 This ADC circuit is limited and rarely used

 Successive Approximation ADC solves these

 Result always n clocks

 Used extensively for

You might also like