Introduction to Nondestructive

Testing
 ADDRESS FOR
COMMUNICATION
M/S. Industrial Radiographic Sevices (P) Ltd. Kota Raj.

CONTACT PERSON : Ashok Kumar Arya-

International Trainer

G-16 Chambal Industrial Area

Opp. Multimetals Kota
Rajasthan
MOB NO : 91-9799496206
FAX NO :
EMAIL : [email protected]
INTRODUCTION TO NDT TRAINING

• SNT –TC-1A – CURRENT EDITION

• ( REF TRAINING STANDARD)
• ASNT – AMERICAN SOCIETY FOR NON
DESTRUCTIVE TESTING
• TC – TECHNICAL COUNCIL
• 1A – VERSION OF DOCUMENT
• CURRENT EDITION ( 2001 ) TILL NOW
 NDT METHODS W.R.T
CERTIFICATION

12 NDT METHODS
• RADIOGRAPHY TESTING
• ULTRASONIC TESTING
• MAGNETIC PARTICLE TESTING
• PENETRANT TESTING
• VISUAL TESTING
• ELECTROMAGNETIC TESTING
 NDT METHODS W.R.T
CERTIFICATION

12 NDT METHODS
• ACOUSTIC EMISSIONS
• VIBRATION MONITOR ANALYSIS
• THERMAL INFRARED TESTING
• LEAK TESTING
• LASER TESTING
• NEUTRON RADIOGRAPHY
 LIMITED CERTIFICATION

RADIOGRAPHY TESTING
• FILM RADIOGRAPHY
• XEROX RADIOGRAPHY
• MICROFOCUS RADIOGRAPHY
• STEREO RADIOGRAPHY
• X-RAY CRAWLER
• REAL TIME RADIOGRAPHY
 LIMITED CERTIFICATION

ULTRASONIC TESTING

• PULSE ECHO TECHNIQUE

• IMMERSION TECHNIQUE
• THROUGH TRANSMISSION TECHNIQUE
 LIMITED CERTIFICATION

MAGNETIC PARTICLE TESTING

CIRCULAR MAGNETIZATION
• HEAD SHOT TECHNIQUE
• PROD TECHNIQUE
• CENTRAL CONDUCTOR TECHNIQUE

LONGITUDINAL MAGNETIZATION
• YOKE TECHNIQUE
• COIL TECHNIQUE
 LIMITED CERTIFICATION

PENETRANT TESTING

• WATER WASHABLE
• SOLVENT REMOVABLE
• POST EMULSIFICATION

Note : classified based on removal of excess

penetrant
 LIMITED CERTIFICATION

VISUAL TESTING
• BOROSCOPE
• FIBEROSCOPE
• TEM/SEM
• HOLOGRAPHY
 LIMITED CERTIFICATION

EDDY CURRENT TESTING

• IMPEDANCE ANALYSIS – METER DISPLAY

• PHASE ANALYSIS – CRT DISPLAY
• MODULATION ANALYSIS – STRIP CHART
RECORDER
 FUNCTIONS & LEVELS OF
QUALIFICATION

• LEVEL- I

1. FUNCTION AS A NDT OPERATOR/TECHNICIAN

2. PERFORM SPECIFIC CALIBRATIONS
3. CARRY OUT TESTING IN PRESENCE OF LEVEL-
II/III
4. NOT AUTHORIZED TO SIGN THE
INTERPRETATION SHEET
 FUNCTIONS & LEVELS OF
QUALIFICATIONS

• LEVEL-II

1. PREPARED WRITTEN PROCEDURES

2. FUNCTION AS NDT INSPECTOR
3. PERFORM SPECIFIC CALIBRATIONS & VERIFY THE
RESULTS
4. AUTHORIZED TO SIGN THE INTERPRETATION
SHEET
 FUNCTIONS & LEVELS OF
QUALIFICATIONS

• LEVEL-III

1. APPROVE THE WRITTEN PROCEDURES

2. ESTABLISH THE TECHNIQUES
3. TRAIN LEVEL –I /II
4. OVER ALL INCHARGE OF NDT JOBS
 MODE OF EXAMINATION

LEVEL-I/II
GENERAL – 40 QUESTIONS – 1 HR – 100 MARKS
( CLOSED BOOK ) – PASSING PERCENTAGE -70%

SPECIFIC – 20 QUESTIONS – 1 HR – 100 MARKS

( OPEN BOOK ) – PASSING PERCENTAGE – 70%

PRACTICAL – 10 QUESTIONS – 2 HRS – 100 MARKS

( 10 SAMPLES ) – PASSING PERCENTAGE – 70%
 MODE OF EXAMINATION

LEVEL-III

BASIC ( MANDATORY PAPER ) -135 QUE- 4 HRS

METHOD ( ANY OF 12 METHODS )

ALL 135 QUE – 4 HRS

ALL 80 QUE – 2 HRS
 TIME PERIOD OF ISSUING
CERTIFICATION

• MAXIMUM TIME PERIOD : SIX MONTHS FROM DATE

OF PASSING EXAM

( LEVEL-I/II) – FOUR MONTHS – SIX MONTHS

NOTE : RE-EXAM SHALL BE CONDUCTED AFTER 60

DAYS IF CANDIDATE FAILED TO MEET PASSING
REQUIREMENTS
 ASME SECTIONS
• SECTION-1 – RULES FOR CONSTRUCTION OF POWER BOILERS
• SECTION-2 – MATERIALS
• PART A – FERROUS MATERIAL
• PART B – NON-FERROUS MATERIAL
• PART C – SPECIFICATION OF WELDING RODS , ELECTRODES &
FILLER METALS
• PART D – PROPERTIES
• SECTION-3 – RULES FOR CONSTRUCTION OF NUCLEAR POWER
PLANT COMPONENTS
• SECTION-4 – RULES FOR CONSTRUCTION OF HEATING BOILERS
 ASME SECTIONS
• SECTION -5 – NON-DESTRUCTIVE EVALUATION

• ARTICLE-2 – RADIOGRAPHY TESTING

• ARTICLE-5- ULTRASONIC TESTING
• ARTICLE-6- PENETRANT TESTING
• ARTICLE-7- MAGNETIC PARTICLE TESTING
• ARTICLE-8- EDDY CURRENT TESTING
• ARTICLE-9-VISUAL TESTING
• ARTICLE-10 – LEAK TESTING
 ASME SECTIONS
• SECTION-6 – CARE & OPERATION OF POWER BOILERS
• SECTION-7- CARE & OPERATION OF HEATING BOILERS
• SECTION-8 – BOILERS & PRESSURE VESSEL CODE
• SECTION-9 – WELDING & BRAZING QUALIFICATION
• SECTION-10- RULES FOR CONSTRUCTION OF FRP
VESSELS
• SECTION-11 – RULES FOR INSERVICE INSPECTION OF
NUCLEAR POWER PLANT COMPONENTS
• SECTION-12- RULES FOR TRANSPORT OF STORAGE
TANKS
 CODES & PURPOSE

• API-1104 – CROSS COUNTRY WELDING PIPELINE

• API-650- ABOVE GROUND WELDED STORAGE TANKS

• ASMEB31.3- PROCESS PIPING

• AWS D1.1 – STRUCTURAL WELDING OF STEEL

 CODES & PURPOSE
• ASME-SEC-VIII- BOILERS & PRESSURE VESSELS CODE

• ASME SEC-IX – WELDING & BRAZING QUALIFICATIONS

• ASME SEC-III – RULES FOR CONSTRUCTION OF NUCLEAR POWER

PLANT COMPONENTS

• ASME SEC-II (PART-C ) – SPECIFICATION OF WELDING RODS ,

ELECTRODES & FILLER METALS
 Selection of NDT METHODS

• TYPE OF MATERIAL
( Whether it is ferrous/non-ferrous/ conductivity
material )
• TYPE OF MANUFACTURING PROCESS
( Whether it is casting, forging, welding , rolling
etc )
• TYPE & ORIENTATION OF DISCONTINUITY
( Whether it is surface / near surface/ sub
surface)
• Cost
 VISUAL TESTING

• ONLY FOR SURFACE DISCONTINUTIES

• FOR ANY TYPE OF MATERIALS
• FOR ANY TYPE OF MANUFACTURING
PROCESS
• TEMPERATURE IS NOT A CONSTRAINT
• BASIC TESTING
• ADVANCE EQUIPMENTS ARE MORE
EXPENSIVE.
 PENETRANT TESTING
• ONLY FOR DISCONTINUTIES WHICH ARE
OPEN TO SURFACE
• FOR NON-POROUS MATERIALS
• TEMPERATURE ( 10 DEG CENTIGRADE TO
50 DEG CENTIGRADE ) .
• HIGH TEMPERATURE PENETRANTS ( 200
DEG CENTIGRADE) SPECIAL TYPE OF
MATERIALS AVAILIABLE.
• LESS EXPENSIVE & BETTER FOR FIELD USE
• PORTABLE CANS ARE AVAILIABLE
• TIME CONSUMING
MAGNETIC PARTICLE TESTING

• ONLY FOR FERROMAGNETIC MATERIALS

• FOR SURFACE & NEAR SURFACE
DISCONTINUITIES
• IMMEDIATE INDICATION
• TEMPERATURE UPTO 300 DEG CENTIGRADE
BY USING DRY POWDERS.
• LESS EXPENSIVE & TIME SAVING
• TESTING POSSIBLE EVEN FOREIGN
MATERIAL EMBEDDED OVER THE SURFACE.
 RADIOGRAPHY TESTING

• FOR SURFACE/NEAR SURFACE/

SUBSURFACE
• FOR ANY TYPE OF MATERIAL
• SAFETY RULES & REGULATIONS SHALL BE
FOLLOWED
• MORE EXPENSIVE & TIME CONSUMING
• RADIATION IS DANGEROUS IF SAFETY IS
NOT FOLLOWED
• LOCATION OF DISCONTINUITY
• DIRECT INDICATION
 ULTRASONIC TESTING

• FOR ANY TYPE OF DISCONTINUITY

• FOR ANY TYPE OF MATERIAL EXCEPT
COARSE GRAINED MATERIAL ( EX:SS, CU)
• DEPTH OF DISCONTINUITY
• IMMEDIATE SIGNAL
• TESTING UNDER NORMAL TEMPERATURE
• SKILL IS REQUIRED
• INDIRECT INDICATION
 Outline
• Introduction to NDT
• Overview of Six Most
Common NDT Methods
• Selected Applications
 Definition of NDT
The use of noninvasive
techniques to determine
the integrity of a material,
component or structure
or
quantitatively measure
some characteristic of
an object.

i.e. Inspect or measure without doing harm.

 Methods of NDT
The
rmo
grap
Visual Micr hy
ow ave
a r ticle
t i ng et ic P
e s Magn
Tap T
Acousti
X-ray c Mi croscop
y
Acoust
ic Emissi en ts t
o n em t ra n
a sur Pe ne
M e iq uid
etic L
Ult agn
ra son M Replication
ic
Lase Eddy
r Inter Curr
Lea kage ferom ent
Fl u x etry
 What are Some Uses
of NDE Methods?
• Flaw Detection and Evaluation
• Leak Detection
• Location Determination
• Dimensional Measurements Fluorescent penetrant indication

• Structure and Microstructure Characterization

• Estimation of Mechanical and Physical Properties
• Stress (Strain) and Dynamic Response Measurements
• Material Sorting and Chemical Composition
Determination
When are NDE Methods Used?
There
ThereareareNDE
NDEapplication
applicationat
atalmost
almost any
anystage
stage
in
in the
theproduction
productionororlife
lifecycle
cycleof
ofaacomponent.
component.
– To assist in product development
– To screen or sort incoming materials
– To monitor, improve or control
manufacturing processes
– To verify proper processing such as heat
treating
– To verify proper assembly
– To inspect for in-service damage
 Six Most Common NDT
Methods
• Visual
• Liquid Penetrant
• Magnetic
• Ultrasonic
• Eddy Current
• X-ray
Visual Inspection
Most basic and common
inspection method.

Tools include
fiberscopes,
borescopes, magnifying
glasses and mirrors.

Portable video inspection

unit with zoom allows
inspection of large tanks
and vessels, railroad tank
cars, sewer lines.
Robotic crawlers permit
observation in hazardous
or tight areas, such as air
ducts, reactors, pipelines.
 Liquid Penetrant Inspection
• A liquid with high surface wetting characteristics
is applied to the surface of the part and allowed
time to seep into surface breaking defects.
• The excess liquid is removed from the surface
of the part.
• A developer (powder) is applied to pull the
trapped penetrant out the defect and spread it
on the surface where it can be seen.
• Visual inspection is the final step in the
process. The penetrant used is often loaded
with a fluorescent dye and the inspection is
done under UV light to increase test
sensitivity.
 Magnetic Particle Inspection
The part is magnetized. Finely milled iron particles coated with a dye
pigment are then applied to the specimen. These particles are attracted to
magnetic flux leakage fields and will cluster to form an indication directly
over the discontinuity. This indication can be visually detected under
proper lighting conditions.
Magnetic Particle Crack Indications
 Radiography
The radiation used in radiography
testing is a higher energy (shorter
High Electrical Potential
wavelength) version of the
electromagnetic waves that we
see as visible light. The radiation can Electrons
come from an X-ray generator or a + -
radioactive source.
X-ray Generator
or Radioactive
Source Creates
Radiation

Radiation
Penetrate
the Sample

Exposure Recording Device

 Film Radiography
The part is placed between the
radiation source and a piece of film.
The part will stop some of the
radiation. Thicker and more dense
area will stop more of the radiation.
The film darkness
(density) will vary with
the amount of radiation
X-ray film reaching the film
through the test object.
= less exposure
= more exposure
Top view of developed film
Radiographic Images
 Eddy Current Testing

Coil's
Coil magnetic field

Eddy current's
magnetic field
Eddy
currents

Conductive
material
 Eddy Current Testing
Eddy
Eddycurrent
currenttesting
testingis
isparticularly
particularlywell
wellsuited
suitedfor
fordetecting
detecting
surface
surfacecracks
cracksbut
butcan
canalso
alsobe
beused
usedtotomake
makeelectrical
electrical
conductivity
conductivityand
andcoating
coatingthickness
thicknessmeasurements.
measurements. HereHereaasmall
small
surface
surfaceprobe
probeisisscanned
scannedover
overthe
thepart
partsurface
surfacein
inan
anattempt
attemptto
to
detect
detectaacrack.
crack.
 Ultrasonic Inspection (Pulse-Echo)
High frequency sound waves are introduced into a
material and they are reflected back from surfaces or
flaws.
Reflected sound energy is displayed versus time, and
inspector can visualize a cross section of the specimen
f
showing the depth of features that reflect sound.

initial
pulse

back surface
echo
crack
echo

crack

0 2 4 6 8 10 plate

Oscilloscope, or flaw
detector screen
 Ultrasonic Imaging
High resolution images can be produced by plotting
signal strength or time-of-flight using a computer-
controlled scanning system.

Gray scale image produced using Gray scale image produced using the
the sound reflected from the front sound reflected from the back surface
surface of the coin of the coin (inspected from “heads” side)
 Common Application of NDT

• Inspection of Raw Products

• Inspection Following Secondary
Processing
• In-Services Damage Inspection
 Inspection of Raw Products
• Forgings,
• Castings,
• Extrusions,
• etc.
 Inspection Following
Secondary Processing
• Machining
• Welding
• Grinding
• Heat treating
• Plating
• etc.
 Inspection For
In-Service Damage

• Cracking
• Corrosion
• Erosion/Wear
• Heat Damage
• etc.
Power Plant Inspection
Periodically, power plants are
shutdown for inspection.
Inspectors feed eddy current
probes into heat exchanger
tubes to check for corrosion
damage.

Pipe with damage Probe

Signals
produced by
various amounts
of corrosion
thinning.
 Wire Rope Inspection
Electromagnetic devices
and visual inspections are
used to find broken wires
and other damage to the
wire rope that is used in
chairlifts, cranes and other
lifting devices.
 Storage Tank Inspection
Robotic crawlers
use ultrasound to
inspect the walls of
large above ground
tanks for signs of
thinning due to
corrosion.

Cameras on
long
articulating
arms are used
to inspect
underground
storage tanks
for damage.
 Aircraft Inspection
• Nondestructive testing is used
extensively during the
manufacturing of aircraft.
• NDT is also used to find cracks
and corrosion damage during
operation of the aircraft.
• A fatigue crack that started at
the site of a lightning strike is
shown below.
 Jet Engine Inspection
• Aircraft engines are overhauled
after being in service for a period
of time.
• They are completely disassembled,
cleaned, inspected and then
reassembled.
• Fluorescent penetrant inspection
is used to check many of the parts
for cracking.
 Crash of United Flight 232
Sioux City, Iowa, July 19, 1989
A defect that went
undetected in an
engine disk was
responsible for
the crash of
United Flight 232.
 Pressure Vessel Inspection
The failure of a pressure vessel
can result in the rapid release of
a large amount of energy. To
protect against this dangerous
event, the tanks are inspected
using radiography and
ultrasonic testing.
 Rail Inspection
Special cars are used to
inspect thousands of miles
of rail to find cracks that
could lead to a derailment.
 Bridge Inspection
• The US has 578,000
highway bridges.
• Corrosion, cracking and
other damage can all
affect a bridge’s
performance.
• The collapse of the Silver
Bridge in 1967 resulted in
loss of 47 lives.
• Bridges get a visual
inspection about every 2
years.
• Some bridges are fitted
with acoustic emission
sensors that “listen” for
sounds of cracks growing.
 Pipeline Inspection
NDT is used to inspect pipelines
to prevent leaks that could
damage the environment. Visual
inspection, radiography and
electromagnetic testing are some
of the NDT methods used.

Remote visual inspection using

a robotic crawler.

Magnetic flux leakage inspection.

This device, known as a pig, is
placed in the pipeline and collects
data on the condition of the pipe as it
is pushed along by whatever is being
transported.
Radiography of weld joints.
 Special Measurements
Boeing employees in Philadelphia were given the privilege of
evaluating the Liberty Bell for damage using NDT techniques.
Eddy current methods were used to measure the electrical
conductivity of the Bell's bronze casing at a various points to
evaluate its uniformity.
For More Information on NDT

The Collaboration for

NDT Education

www.ndt-ed.org

The American Society

for Nondestructive
Testing

www.asnt.org