Scribd
Upload
33 views8 pages

Self Tuning of Controllers1

Uploaded by

azhar3303
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
33 views8 pages

Self Tuning of Controllers1

Uploaded by

azhar3303
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
You are on page 1/ 8

SELF TUNING OF

CONTROLLERS
 What is a Controller
Controller is an active element or device that receives the information from
the measurements and takes appropriate corrective action to adjust the
values of manipulated variables of a process.

 Different Types of Controllers


Proportional controller
Proportional Integral Controller
Proportional Derivative Controller
Proportional Integral Derivative Controller

 Tuning of a Controller
Tuning of a controller may be defined as process of identifying ideal set of
values to a selected controller for a specific process control
We need to obtain the values of Kc, TI and TD for optimizing the process
output.
Ziegler-Nichols Tuning (Ultimate Cycle method)
 Unlike process reaction curve method which uses data from the open loop
response of a system, this technique is a closed loop procedure. It goes through
following steps

1. Bring the system to desired operation level

2. Using proportional control only & with the feedback loop closed, introduce a
set point change and vary proportional gain until the system oscillates
continuously. The frequency at continuous oscillation is known as cross over
frequency ω co. Let M be the Amplitude Ratio of system response at ω co

3. Compute the following quantities

Ultimate Gain Ku = 1/M

Ultimate period of sustained cycling Pu = 2π/ ω co min/cycle


4. Using the values of Ku and M. Ziegler-Nichols have recommended the
following settings for the feedback controls

Kc ŤI ŤD
Proportional Ku/2 --- ---
PI Ku/2.2 Pu/1.2 ---
PID Ku/1.7 Pu/2 Pu/8

The settings above reveal the following


1. For Proportional control alone use of gain margin is equal to 2
2. For PI control use lower Kc because the presence of Integral control mode
introduces additional phase lag at all frequencies with destabilizing effects on
the system. Therefore lower or approximately same is the value of K c a
3. The presence of Derivative control introduces phase lead with strong
stabilizing effects in the closed loop response. Thus Kc can be increased
without threatening the stability of the system
Definition of a Self Tuning controller
A Self tuning controller may be defined as a system capable of readjusting the
controller tuning settings automatically to provide an optimal process output

Blocks of a Self Tuning Controller


System Identifier:
This Item estimates the parameters of the process
Controller Synthesizer:
This element synthesizes or calculates the controller parameters specified by
control objective function
Controller Implementation Block:
This is the controller whose parameters are updated at periodical intervals by
the controller parameter calculator

r: set point; c: controlled output; m: manipulated variable


BLOCK DIAGRAM OF SELF TUNING CONTROLLER

DESIGN CONTROL SYSTEM


CRITERION IDENTIFIER
SYNTHESIS

IMPLEMENTATION
BLOCK

Set Point
(r) m c
+ CONTROLLE PROCESS
R
-

b=c

Fig: The Main components of Self Tuning Regulator


Most self tuning controllers will self tune
-During Startup
-Retune on request
-Retune on naturally occurring upsets
-Continuously when excitation introduced into the process by controller

Advantages of Self Tuning Controllers


1. Facilitates controlling critical processes of systems;
2. Approaches optimum operation regimes;
3. Facilitates design unification of control systems;
4. Shortens the lead times of system testing and tuning;
5. Lowers the criticality of technological requirements on control systems by
making the systems more robust;
6. Saves personnel time for system tuning.
Video on functioning of a Self
Tuning Control (Real Time
Application)
THANK YOU

Presentation by
Ravi Shankar
1 / 2 MTech(Industrial Process Instrumentation) AUCE

You might also like