The Diode
Diode Operation
Voltage to Current Characteristics
Diode Models
BASIC ELECTRONICS WITH
MEASUREMENTS
The Diode
made from a small piece of semiconductor material, usually
silicon, in which half is doped as a p region and half is doped
as an n region with a pn junction and depletion region in
between.
The p region is called the anode and is connected to a
conductive terminal. The n region is called the cathode and
is connected to a second conductive terminal.
Typical Diode Packages
The anode (A) and cathode (K) are indicated on a diode in several
ways, depending on the type of package. The cathode is usually
marked by a band, a tab, or some other feature. On those packages
where one lead is connected to the case, the case is the cathode.
Diode Operation
To bias a diode, apply a dc voltage across it.
1. FORWARD BIAS 2. REVERSE BIAS
Diode Operation
1. FORWARD BIAS
condition that allows current through the pn junction.
This external bias voltage is designated as VBIAS.
The resistor limits the forward current to a value that will not
damage the diode.
1st requirement: the negative side of VBIAS is connected to the n
region of the diode and the positive side is connected to the p
region.
2nd requirement is that the bias voltage, VBIAS, must be greater
than the barrier potential.
Diode Operation
what happens when a diode is forward-biased
Diode Operation
Because like charges repel, the negative side
of the bias-voltage source “pushes” the free
electrons, which are the majority carriers in
the n region, toward the pn junction.
This flow of free electrons is called electron
current.
Diode Operation
The bias-voltage source imparts sufficient energy to the free
electrons for them to overcome the barrier potential of the
depletion region and move on through into the p region.
Once in the p region, these conduction electrons have lost
enough energy to immediately combine with holes in the
valence band.
As the electrons flow out of the p region through the external
connection (conductor) and to the positive side of the bias-
voltage source, they leave holes behind in the p region; at
the same time, these electrons become conduction electrons
in the metal conductor.
Diode Operation
Recall that the conduction band in a conductor
overlaps the valence band so that it takes much less
energy for an electron to be a free electron in a
conductor than in a semiconductor and that metallic
conductors do not have holes in their structure.
There is a continuous availability of holes effectively
moving toward the pn junction to combine with the
continuous stream of electrons as they come across
the junction into the p region.
Diode Operation
Effect of Forward Bias on the Depletion Region
The depletion region narrows and a voltage drop is
produced across the pn junction when the diode is forward-
biased.
Diode Operation
2. REVERSE BIAS
condition that essentially prevents current through
the diode.
This external bias voltage is designated as VBIAS.
Notice that the positive side of VBIAS is connected
to the n region of the diode and the negative side is
connected to the p region. Also note that the
depletion region is shown much wider than in
forward bias or equilibrium.
Diode Operation
what happens when a diode is reverse-biased
Diode Operation
In the p region, electrons from the negative
side of the voltage source enter as valence
electrons and move from hole to hole toward
the depletion region where they create
additional negative ions.
This results in a widening of the depletion
region and a depletion of majority carriers.
The flow of valence electrons can be viewed
as holes being “pulled” toward the positive
side.
Diode Operation
The initial flow of charge carriers is transitional and
lasts for only a very short time after the reverse-bias
voltage is applied. As the depletion region widens, the
availability of majority carriers decreases.
As more of the n and p regions become depleted of
majority carriers, the electric field between the positive
and negative ions increases in strength until the
potential across the depletion region equals the bias
voltage, VBIAS. At this point, the transition current
essentially ceases except for a very small reverse
current that can usually be neglected.
Diode Operation
Reverse Breakdown
Normally, the reverse current is so small that it can be
neglected. However, if the external reverse-bias voltage
is increased to a value called the breakdown voltage, the
reverse current will drastically increase.
Voltage to Current Characteristics
V-I Characteristic for Forward Bias
Forward-bias measurements show general changes in
VF and IF as VBIAS is increased.
Voltage to Current Characteristics
V-I Characteristic for Reverse Bias
The diode reverse voltage (VR) increases to the left
along the horizontal axis, and the reverse current (IR)
increases downward along the vertical axis.
Voltage to Current Characteristics
There is very littlereverse current (usually μA
or nA) until the reverse voltage across the
diode reaches approximately the breakdown
value (VBR) at the knee of the curve.
After this point, the reverse voltage remains
at approximately VBR, but IR increases very
rapidly, resulting in overheating and possible
damage if current is not limited to a safe
level.
Voltage to Current Characteristics
The breakdown voltage for a diode depends
on the doping level, which the manufacturer
sets, depending on the type of diode.
A typical rectifier diode (the most widely used
type) has a breakdown voltage of greater
than 50 V. Some specialized diodes have a
breakdown voltage that is only 5V.
Voltage to Current Characteristics
The Complete V-I
Characteristic Curve
Diode Models
Diode Approximations
1. The Ideal Diode Model
least accurate approximation
can be represented by a simple switch
this model is adequate for most troubleshooting when you are trying
to determine if the diode is working properly.
Diode Models
Diode Approximations
1. The Ideal Diode Model
IDEAL DIODE
when it is forward biased and acts like a
perfect conductor, with zero voltage across it
when the diode is reversed biased, it acts as a
perfect insulator with zero current through it
Diode Models
2. The Practical Diode Model
The practical model includes the barrier potential.
When the diode is forward-biased, it is equivalent
to a closed switch in series with a small equivalent
voltage source (VF) equal to the barrier potential
(0.7 V) with the positive side toward the anode.
Diode Models
2. The Practical Diode Model
Diode Models
2. The Practical Diode Model
Sample Problem
Solution:
Other Types of Diodes
There are several types of diodes besides the standard
p-n junction diode. Three of the more common are:
Zener diodes
Light-emitting diodes
Diode arrays
Zener Diode
A Zener diode is one
that is designed to
safely operate in its
zener/reverse bias
region; biased at the
Zener voltage (VZ).
Common zener diode voltage ratings
are between 1.8 V and 200 V
Light-Emitting Diode (LED)
An LED emits light when it is forward biased,
which can be in the infrared or visible spectrum.
The forward bias voltage is usually
in the range of 2 V to 3 V.
Light-Emitting Diode (LED)
Diode Arrays
Multiple diodes can be packaged together
in an integrated circuit (IC).
Common Anode
A variety of diode
configurations are Common Cathode
available.
Thank you for listening😊❤