Scribd
Upload
64 views27 pages

Teaching Modules For Steel Instruction: Advanced Flexure Design Composite Beam Theory Slides

The document provides information on composite beam theory, including: - Composite beams allow the steel beam and concrete slab to work together, increasing strength and stiffness while reducing steel needs. - Shear connectors like studs transfer shear between the slab and beam and allow the section to act compositely. - The effective width of the slab, shear transfer mechanisms, and calculations for flexural strength of fully or partially composite sections are discussed. - Serviceability considerations include transforming the composite section properties to an equivalent steel section for deflection calculations.

Uploaded by

kiran
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
64 views27 pages

Teaching Modules For Steel Instruction: Advanced Flexure Design Composite Beam Theory Slides

The document provides information on composite beam theory, including: - Composite beams allow the steel beam and concrete slab to work together, increasing strength and stiffness while reducing steel needs. - Shear connectors like studs transfer shear between the slab and beam and allow the section to act compositely. - The effective width of the slab, shear transfer mechanisms, and calculations for flexural strength of fully or partially composite sections are discussed. - Serviceability considerations include transforming the composite section properties to an equivalent steel section for deflection calculations.

Uploaded by

kiran
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 27

Teaching Modules for

Steel Instruction

Advanced Flexure Design


COMPOSITE BEAM THEORY
SLIDES
Developed by Scott Civjan
University of Massachusetts, Amherst

Composite Beam Theory 1


Composite Beams

Composite action accounts for the steel beam and floor slab
working together to resist bending moments.

Advantages over non-composite design:


Increased strength
Increased stiffness

For given load conditions can achieve:


Less steel required
Reduced steel depth

Composite Beam Theory 2


Composite Behavior
c c
NA
NA Concrete
T Composite

NA Steel

T T

Non-Composite Fully Composite


• Slip at Interface • Assumed no slip at Interface
• Two Neutral Axes • One Neutral Axis
• Mn= Mnconcrete+Mnsteel • Mn >> Mnconcrete+Mnsteel
• I = Iconcrete + Isteel • I >> Iconcrete+Isteel
• Shear at interface
transferred by shear
connectors.

Composite Beam Theory 3


Slabs

Composite Metal Deck Slabs – most commonly used today.


Advantages:
Stay in place form.
Slab shoring typically not required.
Metal deck serves as positive reinforcement.
Metal deck serves as construction platform.

Flat Soffit Slabs – typically, older construction.

Composite Beam Theory 4


Effective Width of Slab

beff = effective width of the slab


Function of: Span length
Distance to nearest beam
Distance to edge of slab
beff beff

edge s1 s2 s3 edge

Composite Beam Theory 5


Flat Soffit Slabs

beff

ts, slab thickness

Composite Beam Theory 6


Metal Deck Slab - Ribs Parallel to Beam Span

A beff
tc
hr

A
hr = height of deck
tc = thickness of concrete above the deck
Composite Beam Theory 7
Metal Deck Slab - Ribs Perpendicular to Beam Span

beff A
tc
hr

Composite Beam Theory 8


REFERENCES: COMPOSITE BEAMS

Steel Deck Institute web pages


Nelson Headed Studs web pages
Steel Deck Manufacturer Catalogs
These can be found on-line

Composite Beam Theory 9


Typical Framing
Column
Girder

Beam
Slab/Deck Span

PLAN

Composite Beam Theory 10


INSERT PHOTOS:

AISC Four Story Office Building


Photo Slide Shows
Metal Decking Slides
Shear Studs Slides

Composite Beam Theory 11


Flexural Strength

Composite Beam Theory 12


Flexural Strength
Positive Moment

The strength is determined as the plastic stress


distribution on the composite section.
 

Negative Moment

It typically is assumed that the concrete carries no


tensile forces and reinforcement is minimal, therefore
strength is identical to a bare steel section.
 

Composite Beam Theory 13


Flexural Strength

Positive Moment

Fully Composite: The strength of either the floor slab in


compression or the steel beam in tension is transferred at
the interface.

Partially Composite: The force transfer between the slab


and beam is limited by the connectors.

Composite Beam Theory 14


Flexural Strength

Positive Moment

Lateral Torsional Buckling is prevented by the slab


(continuous bracing).

Local Flange Buckling is minimized by the slab.

In general, strength is controlled by Mp.

Composite Beam Theory 15


INSERT INFORMATION: STRENGTH
OF FULLY COMPOSITE BEAM
SECTION CALCULATIONS

Handout on Calculations:
FullyCompositeCalcs.PDF

Composite Beam Theory 16


Flexural Strength

The bare steel section must support the temporary


construction loads (before the concrete has set), or the
steel beam must be shored until the composite section is
effective.

Composite Beam Theory 17


Shear Transfer Between Slab and Beam

Typically, provided by headed shear studs.

Shear flow, n, is calculated along the interface between slab and


beam.

Minimal slip allows redistribution of forces among shear studs.


Therefore, studs are uniformly distributed along the beam.

The total shear flow, n, must be provided on each side of Mmax.

Composite Beam Theory 18


Shear Transfer Between Slab and Beam

Compression
Force

Tension Force

Composite Beam Theory 19


Shear Transfer Between Slab and Beam

Compression
Force

Tension Force

Composite Beam Theory 20


Shear Transfer Between Slab and Beam

n = shear flow

Composite Beam Theory 21


Shear Transfer Between Slab and Beam

VQ
ν
I tr
n = shear flow to be transferred by shear studs
V = Shear at the location considered
Q = first moment of inertia of area above the interface
Itr = moment of inertia of the transformed cross section

Composite Beam Theory 22


Partially Composite Beam

Consider when fully composite strength is greater than required.


This may occur when:
The choice of shape is based on construction loads.
The choice of shape is based on architectural constraints.
The lightest shape has excess strength.

Composite Beam Theory 23


INSERT INFORMATION: STRENGTH
OF PARTIALLY COMPOSITE BEAM
SECTION CALCULATIONS

Handout on Calculations:
PartiallyCompositeCalcs.PDF

Composite Beam Theory 24


Serviceability

For composite section deflections:


Transform section into equivalent steel section.
Compute center of gravity of transformed section.
Compute Itr of transformed section.

Composite Beam Theory 25


Serviceability
beff beff/n

tc tc
hr hr

Note:
modular ratio, n = Es/Ec

Composite Beam Transformed Beam

Composite Beam Theory 26


Shear Strength

It typically is assumed that the slab carries no shear forces,


therefore composite shear strength is identical to that of a
bare steel section.
 

Composite Beam Theory 27

You might also like