Basic Civil

Engineering Unit I
Surveying – Objects – types- classification- Principles – Measurements
of distances – levelling
Civil Engineering Materials- Bricks – Stones – sand – Cement –
Concrete – Steel Sections
 Surveying
•It is defined as the process of measuring
horizontal distances, vertical distances and
included angles to determine the location of points
on, above or below the earth surfaces.
•The term surveying is the representation of
surface features in a horizontal plane.
•The process of determining the relative heights in
the vertical plane is referred as levelling.

w w w. ar p r a d ee p. t k
 Objectives of Surveying
•The data obtained by surveying are used to prepare the
plan or map showing the ground features.
•When the area surveyed is small and the scale to which
its result plotted is large, then it is known as Plan
•When the area surveyed is large and the scale to which
its result plotted is small, then it is called as a Map
•Setting out of any engineering work like buildings, roads,
railway tracks, bridges and dams involves surveying
 Main divisions of surveying
Types of Surveying
•Plane surveying
• Geodetic surveying
Concept:
•Since the shape of the earth is spheroidal, the
line connecting any two points on the earth
surface is not a straight line, but a curve.
•When the surveys extend over a large areas or
when the accuracy required is great, the curvature
of earth has also to be taken into account.
•For small distances the difference and the
subtended chord
w w w.arprade ep.tk
 Plane Surveying
•The surveying where the effect of curvature of
earth is neglected and earth’s surface is treated as
plane, is called surveying.
•The degree of accuracy in this type of surveying
is comparatively low.
•Generally when the surveying is conducted over
the area less than 260 Sq.Km., they are treated as
plane surveying.
•Plane surveying is conducted for the purpose of
engineering projects.
 Geodetic Surveying
•The effect of curvature is taken into account.
•It is also known as “Trigonometrical Surveying”.
•It is a special branch of surveying in which
measurements are taken with high precision
instruments.
•Calculations are also made with help of spherical
trigonometry.
•It is generally adopted by the Great
Trigonometrical Survey Department of
India”. (GTS).
 Classification of surveying
• Land Surveying
• Marine or Navigation or Hydrographic Surveying
• Astronomical Survey.
Land Surveying: Land survey is a one, in which the relative
points or objects on the earth’s surface is determined.
Marine or Navigational or Hydrographic Survey:
Marine surveying is one in which in which the relative
position of objects under water is determined.
Astronomical Surveying: It is one in which observations
are made to locate the heavenly bodies such as sun,
moon and stars.
 Classification of Land surveying

Topographical Survey:
•It is used for determining the natural and artificial features of
the country such as rivers, lakes, hills and canals.
Cadastral Survey:
•It is used to locate additional details such as boundaries of
fields of fields, houses and other properties.
City Survey:
•It is used for town planning schemes such as laying out plots,
constructing streets, laying water supply and sewer lines.
•Engineering Survey : It is used to collect data for design and
construction of Engineering works such as roads, railways,
bridges dams etc.,
 Principles of Surveying
Principle 1:
•A number of control points are fixed in the area
concerned by adopting very accurate and precise
methods.
•The lines joining these control points will be
control lines.
•Other measurements are made to locate points
inside these control lines.
•Thus, main triangles and traverses are formed
first.
 Principles of Surveying
Principle 1:
•The main triangles and traverses are divided into
smaller ones by using less rigorous methods.
•By doing so, accumulation of errors is avoided
and any local error can be easily identified.
•If survey work is started from a part (smaller
triangle or traverse) and proceeded to whole there
are chances of errors getting multiplied at every
stage.
•Hence any survey work should be from whole
to part and not from part to whole.
 Principles of Surveying
Principle 2:
•New points should be fixed by atleast two
independent measurements.
R
R R

l1
l1 l2

θ1 θ2 θ1

P Q P Q Q
P
Figure 1 Figure 2 Figure 3
 Principles of Surveying
Principle 2:
• As per the Principle 2, the location of a new
point involves one of the following.
(a) Measurement of two distances.
(b) Measurement of two angles
(c) Measurement one angle and one distance
 Principles of Surveying

R R R

l1
l1 l2
θ1 θ2 θ1
P Q P Q P Q
Figure 1 Figure 2 Figure 3

Fig 1: It shows the method of locating R with reference to known length PQ by

using the known distances of PR (l1) and QR (l2)

Fig 2: It shows the method of locating R with reference to the length PQ by using
the known angles QPR (θ1) and PQR (θ2)

Fig 3: It shows the method of locating R with reference to known length PQ by

using the known distance of PR (l1) and known angle QPR (θ1)
 Chain Surveying - Principle
•In chain surveying only linear distances on the
field are measured.
•These distances are used to define the boundary
of field and mark simple details.
Principle :
•It is to form a network of triangles by using the
distances measured.
•Better accuracy will be obtained if the triangles
thus formed are nearly equilateral in shape.
 Classification of surveying
Classification of surveying:
• Chain Surveying
• Compass Surveying
• Theodolite surveying
• Plane Surveying
• Techeometric Surveying
 Accessories used in Chain Surveying

The different accessories used in chain surveying

are
(a) Metre Chain
(b) Chain Pins (arrows)
(c) Measuring Tape
(d) Ranging rod/Offset rod.
 Accessories used in Chain Surveying
Metric surveying chain

•A surveying chain is a device used to measure distance

between two points on the ground.
•Metric chains are available in lengths of 5 m, 10m, 20m and 30
m.
•20m – 30 m chain is normally used for the field of surveying.
•A surveying chain contains brass handles with brass eyebolt
and collar, galvanized mild steel links and wire rings.
•In the case of 20 m and 30 m chains, brass tallies are provided
at every 5 m length and indicating brass wire rings are attached
at every metre length except where tallies are provided.
 Accessories used in Chain Surveying
Metric surveying chain

•The distance between the outside faces of handles of a fully stretched

out chain is the length of the chain.
• The length of the chain, like 20m is engraved on the handles.
•While measuring the long distance, the chain will have to be used a
number of times.
• Arrows are driven at the end of every chain length.
•For holding the arrows in position, grooves are cut in the outside face
of the handles.
• The radius of the groove is the same as that the arrows.
•For convenient handling of the chain, the handle joint is made flexible
so that it is possible to swivel to handle round the eye bolt.
w w w.arprade ep.tk
 Accessories used in Chain Surveying
Chain Pins
•Chain pins or arrows are used with
the chain for marking each chain
length on the ground.
•The arrow is driven into the ground
at the end of each chain length is
measured.
•Chain pins the arrow should be
made of good quality hardened and
tempered steel wire of minimum
tensile strength of 70 kg/mm 2 .
•The overall length is 400 mm and
thickness is 4mm.
• The wire should be black
enamelled.
•The arrow has a circular eye at the
one end is pointed at the other end .
 Accessories used in Chain Surveying
Pegs

•Wooden pegs of 15cm length and 3 cm square

in section are used to establish the station points
or the end points of a line on the ground.
•They are tapered one end and are driven into
the ground by using a wooden hammer.
•About 4 cm is left projecting above the
ground.
 Accessories used in Chain Surveying
Measuring Tape

•There are different types of tapes are used. They

are
(a) Cloth or linen type
(b) Metallic Tape
(c) Steel Tape
(d) Invar Tube.

Metallic tape and steel tapes are most commonly

used.
 Accessories used in Chain Surveying
Measuring Tape

•Metallic Tape is made of varnished

waterproof linen.
•It is reinforced with fine brass
copper or bronze wires.
•Tapes are available in lengths of 10,
15, 20, 30 or 50 metres.
•In metallic tapes every metre is
divided into 100 divisions (cms).
•In steel tapes, the centimetre
division are also subdivided.
 Accessories used in Chain Surveying
Ranging Rod
Ranging Rod:
•It is also known as ranging pole or picket.
•Ranging rod is used for ranging or aligning long lines on the
ground in field surveying.
•Ranging is a straight line means fixing a series of pegs or other
marks such that they all lie on a straight line.
•Ranging rods are used marking points on the ground so that
the positions of the points are distinctly visible from some distant
way.
•The length of ranging rod may be 2 m and 3 m and its diameter
is 30 mm.
•Ranging rod made of steel tube has an internal diameter of 32
mm.
•The ranging rods are made of well seasoned, straight grained
timber of circular cross section.
w w w.arprade ep.tk
 Accessories used in Chain Surveying
Ranging Rod
•Ranging rods should be
straight and free from
warps.
•The deviation in straightness
should not exceed 5mm in a 2
m length.
•The ranging rod is painted
in red and white in alternate
band lengths of 200 m m
each.
•The bottom end of the rod is
fitted with a pointed, hollow,
cast iron shoe or steelw shoe of
w w.arprade ep.tk
 Accessories used in Chain Surveying
Offset Rod
•It is a ranging rod with two
short, narrow, vertical
sighting slots passing
through the centre of the
section.
•A hook is fitted of a groove
is cut at the top to enable
pulling or pushing of the
chain through obstruction
like hedges.
•Offset rods are meant for
setting outlines
approximately at right
angles to the main line.
 Accessories used in Chain Surveying
Cross Staff
•It is used to set out right
angles in chain surveying
•It consists of four metal arms
vertical slits mounted on a pole.
•Two opposite slits are
positioned along the length of a
line (Main Line)
•A line perpendicular to the
main line is formed or
sighted through the other
two slits
 Accessories used in Chain Surveying
Plumb Bob
•It consists of a solid conical
piece and a string attached to
it at its centre.
•When in use, the solid
piece is at the bottom.
•It is used to test the
verticality of the
ranging rods and to
transfer the points to
the ground.
•Plumb bob is used while
doing chain surveying on
sloping ground.
 Accessories used in Chain Surveying
Unfolding and folding of chain
•Both the handles of the chain are held in the left hand and
the other portions in the right hand.
• The portion held in the right hand is thrown forward;
• The person throwing moving backward himself.
•The leader takes one handle of the chain and moves forward
himself.
•The leader takes one handle of the chain and moves forward
till the chain is stretched to its full length.
• The chain should be free from any kinks or bends.
•After the completion of the work, the two handles are
brought together and the chain is folded started with the
middle pair.
• The links are placed obliquely across each pair.
• The folded chain is securely tied with a rope
w w w.arprade ep.tk
 Ranging a line
•It means fixing a series of pegs or other marks
such that they all lie on a straight line.
•Suppose P and Q are the two ends of a survey
line.
• One ranging rod is driven Q.
•The surveyor holds another ranging rod at P and
stands at about 30 cm behind ranging rod.
•The assistant goes with another ranging rod
along the survey line and positions himself
approximately in line with PQ at a distance less
than a chain length from P.
 Ranging a line
• The surveyor at P keeps his eye in line with PQ
and signals to the assistant by way of
adjusting the position of the ranging rod held
by the assistant traversely.
• This adjustment is continued till the
intermediate ranging rod is truly in line with P
and Q.
• Other intermediate points along the survey line
are also fixed in the same manner.
 Outline of Chain surveying
•A base line which is a chain line is fixed.
• The base line is aligned by ranging.
• The length of the line is measured by chaining.
•For this follower holds the zero end of the chain and the
leader drags the chain to an intermediate point on the line
•The leader straightens the chain by jerking till the chain
lies exactly over the line.
•The leader marks the end of the chain by driving the
chain pin (arrow)
•The follower holds the zero end of the chain at the chain
pin point again
•Thus the chaining is continued till the entire length is
covered.
 Outline of Chain surveying
•For locating the details, lateral measurements are
taken to the objects.
•These lateral measurements are called offsets.
•If the offset is at right angles to the base line, it is
called perpendicular offset.
•If it is inclined to the base line, it is called oblique
offset.
•Depending upon the situation, perpendicular or
oblique offsets are taken
•The length are measured are entered.
 Advantages and disadvantages
of chain surveying

Advantages:
•It is simple
• It does not require any costly equipment
• It is adopted for preparing plans for small area
Disadvantages:
• It cannot be used for large areas
•It cannot be used in thick bushy areas with ups
and downs.
• Chain surveying is not always accurate.
Compass Surveying – Prismatic Compass
 Compass Surveying
•Whenever a number of base lines
are to be run for obtaining the
details as in traversing, just linear
measurements made by chain
surveying will not be sufficient.
•The angles included between the
adjacent lines should also be
measured
•Compass is one of the
instruments used to measure the
angles.
 Prismatic Compass
Description:
•A magnetic needle is balanced over a pivot in a circular box of 85
mm to 110 mm in diameter.
• A graduated aluminium ring is attached to the magnetic needle.
• An agate cap keeps the aluminium ring stable.
• The box is covered by a glass lid.
•Object vane and eye vane are provided at diametrically opposite
ends.
•Eye vane caries a reflecting prism which can be raised or lowered as
desired.
•A vertical horse hair or fine wire is provided at the middle of the
object vane.
•The graduations in the aluminium ring are made in the clockwise
direction starting with 0o at South and 180o at North with inverted
markings.
 Prismatic Compass
Description:
•A triangular prism fitted below the eye slit enables
magnification of readings to suit observer’s eye.
•Based on this prism arrangement, the compass is
named prismatic compass.
•Compass is fixed over a tripod with ball and socket
arrangement.
•A braked pin is provided below the object vane to
damp the oscillations of the magnetic needle while
taking readings.

w w w. ar p r a d ee p. t k
 Prismatic Compass
Working Principle:
•The magnetic field aligns itself with the magnetic meridian (N-S
direction)
•The line of sight is actually the line joining the object vane and eye
vane
•The angle between the N-S direction and the line of sight is
observed in the compass
•This angle is actually the angle between N-S direction and the line
on the ground
• This angle made by the line with the N-S direction is called the
bearing of the line.
•Compass is used to measure the bearing of the different lines from
which the angles included between the adjacent lines are computed.

w w w. ar p r a d ee p. t k
 How to take reading using compass

•The compass is centered over the station by dropping a small

piece of stone from the centre of the bottom of the compass.
• A plumb bob is used for centering.
•The compass is levelled by adjusting the ball and socket till the
top of the box is horizontal.
•The graduated ring should move freely after having levelled
the instrument.
• Suppose the bearing of a line PQ is to be observed.
• The compass is centered over P.
• It is levelled.
• The prism and the object vane are kept in vertical position.
•The compass is turned slowly till the ranging rod already
erected at Q is bisected.

w w w. ar p r a d ee p. t k
 How to take reading using compass

•In this position, the ranging rod, the object and

the eye vane all lie in the same line.
•The focusing prism is raised or lowered till the
readings were clear and sharp.
•The reading in the ring cut by the object hair line
is taken after damping the oscillations of the ring
by pressing the brake pin.

w w w. ar p r a d ee p. t k
 Definitions
Magnetic Bearing:
•It is the angle between the magnetic meridian and the line.
•The angle is always measured in the clockwise direction
•It is the direction shown by a freely suspended magnetic needle
•The magnetic meridian is also called bearing.
True Bearing:
•True bearing of a line is the angle between the true meridian
and the line.
•The angle is always measured in the anticlockwise direction.
•The true meridian is the line joining the geographical north and
south bearings.

w w w. ar p r a d ee p. t k
 Definitions
Whole Circle Bearing:
•The bearing of lines measured from the North is called Whole
Circle Bearing.
• The angle is reckoned in the clockwise direction from 0o
coinciding with the north.

Quadrant Bearing:
• The whole circle is divided into four quadrants.
•The bearing is expressed with N or S as prefix and E or W as
suffix.
• Quadrant Bearing is also known as Reduced Bearing.

w w w. ar p r a d ee p. t k
 Definitions
Fore Bearing and Back bearing:
•Every line has two bearing namely fore bearing and back back
bearing
•Fore bearing is the bearing taken in the direction of surveying
and Back bearing is the bearing taken in the reverse direction.
•The difference between the fore bearing and the back
bearing should be 180o.
•It means that one or both stations of the line are
subjected to
local attraction.
•Thus, local attraction is the influence caused on the measured
bearings of lines due to the presence of materials like railway
track, current carrying wires or cables, etc.,
w w w. ar p r a d ee p. t k
 To find QB from WCB
N
A

35 O 15’

W E
P

S
Solution :
Line PA lies in 1st quadrant.
Quadrant Bearing bearing of PA = N 35o 15’ E
w w w.arprade ep.tk
To find QB from WCB

W P 130 O 0’ E

50 O
B
S
Solution :
Line PB lies in 2nd quadrant.
Quadrant Bearing bearing of PB = S 50o 00’ E
w w w.arprade ep.tk
To find QB from WCB
N

P E
210 O 15’

C 30 O 15’
Solution :
S
Line PC lies in 3rd quadrant.
Quadrant Bearing bearing
of PC = S 30o 15’ W
w w w.arprade ep.tk
 To find QB from WCB

D
69 O 15 ’

W P E
290 O 45 ’
Solution :
S Line PD lies in 4th
quadrant.
Quadrant Bearing bearing
of PD = N 69o 15’ W
w w w. ar p r a d ee p. t k
To find Whole Circle Bearing from QB

(i) WCB = PA –N 15o E

(ii) WCB = PB – S 25o 45’ E
(iii) WCB = PC – S 45o 30’ W
(iv) WCB = PD – N 10o W

w w w. ar p r a d ee p. t k
To find Whole Circle Bearing from QB

Qn: PA – N 15o E
Ans: Line PA is in the first quadrant. Its WCB is 15o
N
A

15 O

E
W P

w w w. ar p r a d ee p. t k
To find Whole Circle Bearing from QB

Qn: PB – S 25o 45’ E

Line PB is in second quadrant. Its WCB is 180o00’-
25o45’ = 154o15’ N

154 O 15’
E
W P

B
S

w w w. ar p r a d ee p. t k
To find Whole Circle Bearing from QB

Qn: PC – S 45o 30’W

Line PC is third quadrant. Its WCB is
180o00’+45o30’ = 225o30’ N

E
W P

225 o 30’
B
c S
w w w. ar p r a d ee p. t k
To find Whole Circle Bearing from QB

Qn: PD – N 10o W
Line PD is in fourth quadrant. Its WCB is
D
N
360o00’-10o00’= 350o00’
350 o 00’

E
W P

w w w. ar p r a d ee p. t k
 To find Back Bearing from Fore Bearing

Qn: Fore bearing of Line PQ is 38o15’, find Back

bearing.
Q

B a ck Bearing =218 o 15’

38 o 15’

w w w. ar p r a d ee p. t k
 To find Back Bearing from Fore Bearing

Qn: Fore bearing of Line RS is 210o15’ find the

back bearing.
R

210 o 15’

B a c k Bearing =30 o 30’

w w w. ar p r a d ee p. t k
 Levelling
•It is a surveying method used to determine the level of
points/objects with reference to the selected datum.
•It is also used to set out engineering works.
Uses of Levelling:
• To determine the difference in levels of points/Objects
• To obtain contour map of an area
• To obtain cross section of roads, canals etc.,
•To determine the depth cutting and filling in engineering
works.
•To establish points or erect machinery or construct a building
component at a predetermined level.

w w w. ar p r a d ee p. t k
 Important Terms
Bench Mark: It is surveyor’s mark cut on a stone/
rock or any reference point used to indicate a
level in a levelling survey.
Reduced Level:
•Reduced level of a point is the level of the point
with respect to the level of permanent feature or
bench mark.
•It indicates whether the point is above or below
the reference point (datum).

w w w. ar p r a d ee p. t k
 Instruments used in levelling
Instruments used in levelling are,
(i)Levelling instrument
(ii)Levelling staff
Levelling Instrument :
• Simplest form of levelling instrument is dumpy
level.
• The different parts of levelling instrument are,
(a) Telescope (b) Eye-piece (c) focussing knob (d) level
tube (e) cross bubble (f) foot screws (g) levelling head
(h) diaphragm (i) ray shade
w w w. ar p r a d ee p. t k
 Instruments used in levelling
Instruments used in levelling are,
(i)Levelling instrument
(ii)Levelling staff
Levelling Instrument :
• Simplest form of levelling instrument is dumpy
level.
• The different parts of levelling instrument are,
(a) Telescope (b) Eye-piece (c) focussing knob (d) level
tube (e) cross bubble (f) foot screws (g) levelling head
(h) diaphragm (i) ray shade
w w w. ar p r a d ee p. t k
Dumpy Level

w w w. ar p r a d ee p. t k
 Levelling Staff
•It is an important accessory used with levelling instrument at the time
of conducting levelling survey.
•Reading is taken on the levelling staff held properly at the point
concerned by viewing through the telescope of the levelling instrument.
•Usually 4 m levelling staff may be used of folding type or telescopic
type
•Aluminium levelling staff foldable at every metre length has also
came to the market.
• The levelling staff consists of three pieces.
•The topmost one slides into the middle one and the middle portion
slides into the bottom one.
•When the staff is fully pulled, it will read exactly 40 decimeters (4m)
from the bottom shoe.

w w w. ar p r a d ee p. t k
 Levelling Staff
Graduation in levelling staff:
•Every metre length is divided into 200 divisions.
•The divisions are painted in black and white alternately of thickness
5 m m each.
•The graduation figures are marked at every decimeter length.
•The number indicating metre is in red and the decimeter number is
in black.
• Thus, a graduation figure of 24 indicates 2 metres and 4 decimeters.
•The graduation are made continuously one above the other in the
same line.
•The division lines should be parallel to the base of the bottom shoe
and perpendicular to the length of the staff.
•The edges of the division lines should be straight sharply defined.
•They should be clear and made distinctly visible by properly
contrasting.
•The graduation colour paints used should not crack or blister when
exposed to adverse or atmospheric conditions.
w w w.arprade ep.tk
 Important Terms in levelling
•Station : In Levelling, the term station always refers to the point where
the levelling staff is held and not the instrument station.
•Height of Instrument : It is the elevation of the line of sight with
reference to the assumed datum.
•Back Sight (B.S) : It is the reading taken on the staff held at a point, the
elevation of which is known already. It is useful to know the new height
of the instrument.
•Foresight (F.S): It is the reading taken on the staff held at a point of
unknown elevation. From, F.S., the height of the line of instrument above
the point can be obtained. It is useful to find the elevation of the point.
•Change Point : It is the point at which the fore sight is taken from one
instrument station and back sight is taken from the next instrument
station.
•Intermediate station : A point between two change points is known as
intermediate station. Only one reading is taken on the intermediate
station.
w w w. ar p r a d ee p. t k
 Methods of Levelling
•Method 1 : It is done with only one
setting of the instrument.
•Method 2: When the two station points
are wide apart and the instrument is set
up at more than one point and the
levelling is carried out.

w w w. ar p r a d ee p. t k
 Method 1
With only one setting of the instrument
•The instrument is set u p at a point between P and Q and
the temporary adjustments carried out.
•The levelling staff is held at P, the elevation of which is
known already.
•A back sight is taken on the staff held at P. The staff is
then held at Q and the foresight is taken.

w w w. ar p r a d ee p. t k
 Method 1
With only one setting of the instrument

Height of the instrument = Known elevation of P + the

staff reading at P
= 100.00+ 2.10 = 102.10 m
Elevation of Q = Height of the
instrument – the staff
reading at Q
w w w.arprade ep.tk
= 102.10 – 1.80 = 100.30 m
 Method II
When the station points are wide apart, the instrument is setup for
at more than one point and levelling is done
(Height of Collimation Method)

•A change point (C.P) is established in between P and

Q.
•A back sight is taken at P and a fore sight is taken at the
change point.
•The instrument is shifted to another point between the
change point and Q.
•A back sight is taken at the change point and a fore sight
is taken at Q.
•Any number of change points are established as
required.
• This method is known as Height of Collimation
method. w w w. ar p r a d ee p. t k
 Method II
When the station points are wide apart, the instrument is setup for at
more than one point and levelling is done
(Height of Collimation Method)

The elevation of change point = Elevation of P + Back sight at P – Fore

sight at change point (C.P)
= 100.00+1.60-1.10 = 100.50 m
The second height of the instrument = The elevation of change point+
Back Sight at change point
= 100.50+1.25 = 101.75 m
The elevation of Q = The second height of instrument –
foresight at Q
= 101.75 – 1.81 = 99.94 m
w w w. ar p r a d ee p. t k
 Rise and Fall Method of calculating the level

•The staff readings of the points observed from the same

setting of the instrument are compared.
•It is found whether a point is above or below the
preceding point.
•If the point is above, the staff reading will be less than the
preceding point. The difference between the staff readings is
called rise.
•If the point is below the preceding point, the staff reading
will be greater than that at the preceding point. The
difference between the staff readings is termed fall.

w w w. ar p r a d ee p. t k
 Rise and Fall Method

The difference between the staff readings

at P and Q = 2.10 – 1.80 = 0.30 (rise)

Hence, level of Q = Elevation of P + Rise

= 100.00+0.30 = 100.30 m

w w w. ar p r a d ee p. t k
 Rise and Fall Method
Back Intermedi Fore Rise Fall Reduced Remarks
sight ate sight Level
station

1.245 100.00 BM

2.100 0.855 99.145

2.425 0.810 1.290 100.435 STATION A

0.480 1.945 102.380 STATION B

∑BS ∑FS ∑RISE ∑FAL

3.670 1.290 3.235 L
0.855

w w w. ar p r a d ee p. t k
 Arithmetical Check of Rise and
Fall method

∑ B.S - ∑F.S = ∑Rise - ∑ Fall = Last R.L – First R.L.

3.670 – 1.290 = 3.235 – 0.855 = 102.380 –

100.00
2.380 = 2.380 = 2.380

w w w. ar p r a d ee p. t k
 Fly Levelling
•Any number of change points are established as required
during levelling. This method is known as fly levelling.
•It is adopted to find the difference in level between two
points, when
(i) The two points are too far away
(ii) the difference in level between two points is large
(iii) there are no obstructions in between the two points
concerned.

w w w. ar p r a d ee p. t k
 Calculation of Areas
•One of the purposes of surveying is to determine the area to be
surveyed.
•The area of the land obtained by surveying actually refers to the area
as projected on a horizontal plane.
•There are different methods of computing the area of land using the
data obtained by surveying.
•

w w w. ar p r a d ee p. t k
 Calculation of area by Trapezoidal Rule

•In trapezoidal, a convenient base line is established.

•Perpendicular distances from the base line to the boundary of the land
concerned are measured at regular (equal) intervals along the base line.
•These perpendicular distances are called ordinates.

1 2 3 4
h2 h3 h4 h5
h1

d d d d

w w w. ar p r a d ee p. t k
 Trapezoidal rule
Total Area,
A= d/2 (h 1 +h n +2(h 2 +h 3 +…….+h n-1 ))

w w w. ar p r a d ee p. t k
 Simpsons Rule
• This rule is applicable only if the number of ordinates is odd.
A = d / 3 (First Ordinate+ Last Ordinate + 2 (sum of odd ordinates)
+ 4(sum of even ordinates)

i. e. A = d/3 (h 1 +h n + 2(h 3 +h 5 +h 7 +…..+h n-2 )+ 4(h 2 +h 4 +….+h n-1 )

•If the number of ordinates is even, the area of the last trapezoid is
calculated separately and added to the result.

w w w. ar p r a d ee p. t k
 Problems on Simpsnon’s Rule and Trapezoidal
Rule

1.The following perpendicular offsets were taken at 10 m intervals from

a survey line to an irregular boundary line:
3.60, 2.80, 4.50, 8.25, 7.85, 6.45, 5.35.
Calculate the area enclosed between the survey line and boundary
line by trapezoidal rule and Simpson’s rule.

2.A series of offsets were taken at 5 m intervals from a chain line to a

curved edge.
1.50, 1.66, 2.25, 2.80, 1.75, 1.95, 0.
Calculate the area between the chain line and the irregular boundary
to the curved edge by the Simpson’s rule and Trapezoidal Rule

w w w. ar p r a d ee p. t k