In ASTM Standard, What Is The Instrument Used in Determining Viscosity?

301.
In ASTM standard, what is the

instrument used in determining
viscosity?

Answer: Saybolt Universe
Viscometer
302. In what country that the
present theory of hydrodynamic
lubrication originates from?

Answer: England
303. In viscosity chart, Raimond-
Boyd analysis assumed that the
viscosity of the lubricant is
_________

Answer: Constant

304. In viscosity chart, Raimond-
Boyd analysis assumed that the
viscosity of the lubricant is
_________

Answer: Constant

305. What is the term applied to
the reciprocal of the velocity ratio?
Value
Answer: Train
306. For very slender column,
what type of formula that is best
applied?

Answer: Column Formula

307. Which of the following is the
type of failure due to unstability?

Answer: Buckling

308. What type of spring made in
the form of dished washer?

Answer: Believille Spring
309. What is the minimum number
of teeth on a smaller sprocket for
high speed?
Answer: 21
minimum number of teeth on a
smaller sprocket for moderate
speed?
Answer: 17
311. What is the minimum number
of teeth on a smaller sprocket for
low speed?
Answer: 12
312. Two shaft at right angles to
each other may be connected by
what arrangement?
Answer: Quarter Turn

313. What is the recommended
initial tension of the belt?
Answer: 75 lb/in of Width

314. The process by which high
pressure is applied to a heated
metal billet or blank which causes
it to flow through restricted
orifice.
Answer: Extrusion
315. A tolerance where the size of
a part is permitted to be either
larger or smaller than the given
dimension.
Answer: Bilateral
316. In a pressure vessel, the ratio
of minimum strength of joint to
the strength of solid joint is known
as
Answer: Relative Strength

317. When tested in compression,
ductile material usually
exhibit________ characteristics up
to the yield strength as they do
when tested in tension.

Answer: Approximately the Same
318. In pure torsion, the maximum
stress is at the center of the ___

Answer: Long Sides
319. A method whereby a gear is
run with another gear that has
abrasive surface material.
Answer: Lapping
320. What is material produced if
austenite is cooled rapidly to 400
deg. F or less?
Answer: Martensite
321. Stainless steels are iron-based
alloys that contain at least how
many percent chromium?
Answer: 12%
322. The very high carbon steels
have good quench-harden ability
up to how many percent
chromium?
Answer: 18%
323. A widely used in tool steels
considering that it will maintain its
hardness even it is red heat. The
effect is like molybdenum, except
it is to be added in greater
quantities.
Answer: Tungsten
most widely used cast materials?
Answer: Gray Cast Iron

325. What is the result if all the
carbon in cast iron is in the form of
cementite and pearlite with not
graphite present?
Answer: White
326. Which of the following is a
characteristic of aluminium and its
alloys?
Answer: Resistance to Corrosion, High

Thermal and Electrical Resistance,
Strength to Weight Ratio
327. The corrosion resistance of
aluminium alloys depends upon
which of the following?
Answer: Thin Coating Oxide

328. Which of the following cannot
be a Poisson’s ratio of material?
Answer: 0.57
329. Type of roller bearing in which
the balls are assembled by the
eccentric displacement of the
inner ring.
Answer: Deep-groove Ball Bearing

330. Which of the following is not a
type of ball bearing?
Answer: Shallow-groove Ball Bearing

331. The following is the
approximate density of the leather
belt?
Answer: 0.035 lb/in^3

332. The breaking strength of oak-
tanned beltings varies from 3 to
more than:
Answer: 6 ksi
333. Based on experience, what is
the most economical design belt
speed?
Answer: 6000 to 7500 fpm

334. The tension in the belt due to
centrifugal force increasing rapidly
above about
Answer: 2500 fpm

335. What is the recommendation
speed for leather belt?

336. What is the recommended
speed for fabric belts?

statement of how the total
moment is derived from a number
of forces acting simultaneously at
a point?
Answer: Varignon’s Theorem

338. It is the measure of the
material’s ability to yield and
absorb highly localized and rapidly
applied stresses.
Answer: Toughness
339. What is term applied to the
load at which a column fails?
Answer: Critical Load

340. It is otherwise known as the
percentage difference in solid and
working deflections?
Answer: Working Allowance

341. It is known as the shaft’s
natural frequency of vibration.
Answer: Critical Speed

342. What do you call the mixture
of the solid ingredients with no
solubility?
Answer: Eutectic Alloy

343. Which of the following terms
applied to an interrupted
quenching process resulting in an
austenite to bainite transition?
Answer: Austempering
344. Which of the following
processes where the material will
become progressively stronger,
harder and more brittle until
eventually fails?
Answer: Cold Working

345. In damped free vibration,
when the system returns to its
static position with the ……
equilibrium, the system is said to
be
Answer: Critically Damped

346. Balancing or grinding wheel is
done to
Answer: Equalize the Weight in Every

Portion of the Wheel
346. Materials used for armors
created from insects or waste
(Spider’s web)
Answer: Kivlar
347. A grinding wheel is marked as
51A 46L 5V 23, out of these 5
means
Answer: Structure
348. It is also known as diamond
pyramid hardness test, uses a
pyramid shaped diamond indenter
and a load that ranges from 1 kg to
120 kg.
Answer: Vickers Test

dynamometer is widely used for
absorption of wide range of
powers at wide range of speeds?
Answer: Hydraulic
dynamometer is used for power
measurement when the speed is
high and the viscous force is small?
Answer: Tesla Fluid Friction Dynamometer

351. In case of spur gears the flank
of the tooth is
Answer: The Part of the Tooth Surface

Lying Below the Pitch Surface
352. The cam angle is
Answer: The Angle of Rotation of the Cam

for a Definite Displacement of the Follower
353. Slip in belt drive is
Answer: Difference Between the Linear

Speed of the Rim of Pulley and the Belt on it.
354. Multiple collars are provided
on a flat collar pivot bearing to
Answer: Distribute the Axial Load due to

Limiting Bearing Pressure on a Collar
355. In gramophones for adjusting
the speed of the tum-table, the
following type of governor is
commonly used
Answer: Pickering Governor

356. Shearing the sheet into two
or more pieces
Answer: Parting
357. The mechanism used to
enlarge or reduce moments for
reproducing drawings to different
scales is called
Answer: Bantograph
higher pair?
Answer: Tooth Gearing Mechanism

359. A process of indenting but not
breaking through the surface of a
work piece with a punch in order to
produce a cavity of an impression
Answer: Piercing
360. What describes very rough
grinding such as that performed in
foundries to remove gates, fins
and risers from castings?
Answer: Snagging
single measure that combines the
external dynamic load of an
application with a gear drive’s
reliability and operating life?
Answer: Reliability Factor

362. What is the term used to
described the distance from a
point on one gear to the
corresponding point measures
along the base circle?
Answer: Normal Pitch

best method used for increasing a
spring’s fatigue life?
Answer: Shot Peening

364. It is one of the rigid
members /bodies joined together
to form a kinematic chain.
Answer: Link
365. What is the term applied to
parallel forces equal in magnitude
but opposite direction?

Answer: Couple
366. The kinematics chain in which
one link is considered fixed for the
purpose of analysis but motion is
possible in other links.
Answer: Frame

In ASTM Standard, What Is The Instrument Used in Determining Viscosity?

Uploaded by

Document Informationclick to expand document information

Copyright:

Available Formats

In ASTM Standard, What Is The Instrument Used in Determining Viscosity?

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

In ASTM Standard, What Is The Instrument Used in Determining Viscosity?

Uploaded by

Copyright:

Available Formats

301.

In ASTM standard, what is the

Answer: Quarter Turn

Answer: 75 lb/in of Width

Answer: Relative Strength

Answer: Gray Cast Iron

Answer: Resistance to Corrosion, High

Answer: Thin Coating Oxide

Answer: Deep-groove Ball Bearing

Answer: Shallow-groove Ball Bearing

Answer: 0.035 lb/in^3

Answer: 6000 to 7500 fpm

Answer: 2500 fpm

Answer: 7000 to 8000 fpm

Answer: 4000 to 5000 fpm

Answer: Varignon’s Theorem

Answer: Critical Load

Answer: Working Allowance

Answer: Critical Speed

Answer: Eutectic Alloy

Answer: Cold Working

Answer: Critically Damped

Answer: Equalize the Weight in Every

Answer: Vickers Test

Answer: Tesla Fluid Friction Dynamometer

Answer: The Part of the Tooth Surface

Answer: The Angle of Rotation of the Cam

Answer: Difference Between the Linear

Answer: Distribute the Axial Load due to

Answer: Pickering Governor

Answer: Tooth Gearing Mechanism

Answer: Reliability Factor

Answer: Normal Pitch

Answer: Shot Peening

You might also like