Scribd
Upload
290 views

Moshell Commands and Read Through

1. Moshell commands are used to check basic site configuration including electrical and mechanical tilt, alarms, neighbors, and licensing. 2. License checks can be done through moshell by navigating to the license directory and viewing the license keys file. 3. To check which RNC a site is connected to, log into moshell, quit the current RNC, and use "get 1" which will return the connected RNC, then reconnect to that RNC.

Uploaded by

Linda Jason
Copyright
© © All Rights Reserved
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
290 views

Moshell Commands and Read Through

1. Moshell commands are used to check basic site configuration including electrical and mechanical tilt, alarms, neighbors, and licensing. 2. License checks can be done through moshell by navigating to the license directory and viewing the license keys file. 3. To check which RNC a site is connected to, log into moshell, quit the current RNC, and use "get 1" which will return the connected RNC, then reconnect to that RNC.

Uploaded by

Linda Jason
Copyright
© © All Rights Reserved
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 15

MOSHELL COMMANDS

Moshell basic checks


(Secure CRT)
1. Basic command
• Initial Site Configuration
moshell u****
lt all
get ret elec // Electrical tilt
get ant mech // Mechanical tilt (1st ant) other e.g. scram, cpich,max (at RNC level)
get utrancell primaryscramblingcode xx
get all beam ( Azimuth )

• Alarm Checks
moshell u**** and moshell **RNC1
lt all
Ala ( Active alarms)
Lga (existing alarms)

• Neighbour Checks
moshell **RNC1
lt all
get relation=*** utranrel
get relation=*** gsmrel
2. Licence check
MOSHELL CITRIX (presentation attached)
moshell uxxx Right click on desktop and open
lt all OSS Network Explorer >> Configuration >>Manage HW
license key & SW Inventory >> Software Management organiser
(SMO)
OR Network > Root > ONRM_RootMo
moshell uxxx Select RNC
lt all Select RBS (in RBS Group 1)
cd /c/license
Right click view license key
ls Directory should contain licensekeys.xml
cat licensekeys.xml

Citrix License
checks
3. To check which RNC is connected to which node

• Secure CRT - Logon


• Quit from this RNC q
• To find out which RNC moshell u****
get 1 Result  “Connected to Ubnetwork=**RNC*”
q

• To find out which RBS Type get 0


• To connect to relevant RNC moshell **RNC1

•
or
• U****> lt all ( moshell to site then load all )

Connected to 10.207.86.81 SubNetwork=ONRM_RootMo_R,SubNetwork=PERNC1,MeContext=U0732-


Sandhoogte_Wtr_Purif,ManagedElement=1)
Connected to 10.207.86.81 SubNetwork=ONRM_RootMo_R,SubNetwork=PERNC1,MeContext=U0732-
Sandhoogte_Wtr_Purif,ManagedElement=1)
Last MO: 1014. Loaded 1014 MOs.
4. Pre-Activation checks (Moshell)

• Site Checks
License
Alarms
Electrical tilt
Mechanical tilt

• RNC Checks
Alarms
Neighbours
- 3G
- GSM
Channels configured and enabled
EUL configured on the site
Get uemea|power
4. Pre-Activation checks cont…

• Check all channels are exist


Check that the channels exist on the RNC, can also be checked here that EUL is configured on the site.
moshell **RNC1
lt all
lst .****
• Attached below are examples of moshell
commands used in the tuning process.
RBS example
RBS Commands

RNC example
RNC Commands

Moshell Commands
•
Extra Commands
1. Checking license files from
MoShell
moshell to the site
lt all
cd /c/license
ls
cat licensekeys.xml

OR

moshell U****
lt all
license key

1. Check the software key/WCDMA RBS key for UL to see if it is less than 128
2. Check the software key/WCDMA RBS key for DL to see if it is less than 128
. Neighbour Checks
moshell <RNC>
lt all

get relation=<site> utranrel //gets all 3G neighbour elations for


particular site

get relation=<site> gsmrel //gets all 2G neighbour relations


for particular site

get relation=<site> //gets relation & attributes

pr relation=<site> //prints 2G & 3G relations


4. Pre-Activation checks cont…

• UTRAN Cell Parameter checks


(Cell parameter verification against MTN default (Inner / Border cells)  “parameter_check_ph3_PA03 /
cluster_parameters”)
moshell **RNC1
lt all

P5:
get utrancell=****A1 !(accessClassesBarred|aseLoadThreshold|
pwrLoadThreshold|rateSelection|reservedby)

get uemea|power //RNC parameters


5. Check site live

• Has reference for unlocking the site been received? If so proceed!

– Cell unreserved
get cell=*** cellreserved

• NLRNC1> get cell=794 cellreserved

• UtranCell=794C1 cellReserved 1 (NOT_RESERVED)


• UtranCell=794B1 cellReserved 1 (NOT_RESERVED)
• UtranCell=794A1 cellReserved 1 (NOT_RESERVED)

• Not reserved – site carrying traffic


• Reserved status – site not carrying traffic

Remote
Site Live email Excel Templates Ref num emailTuning-Verification Process 2
6. OSS -NCS Neighbour relations

• Schedule NCS-W Measurements


• CITRIX → Performance → Radio NW Optimisation (RNO)
• File → New Recording → NCS
• Tick Measure WCDMA (only), un-tick Measure GSM if it is ticked
• Insert hours – start time and finish time
• Select cells, choose RNC, find site, copy cells
• Save and schedule.

• Retrieve NCS-W Measurements when recording is finished


• File → Export → Custom Post Processing
(2 files are produced a *.conf and *.msmt)
• Write down the directory in which the two files are located
• Go to this directory on the OSS and take a copy of the *.msmt file and
save it onto your hard drive
• Open this file with MS Excel (this file contains information on missing
and defined neighbours)
1. To connect to site
support@satlx1o> moshell u0456

To check the version loaded:


Cvls

Secure CRT - Logon


Quit from this RNC q
To find out which RNC moshell u****
get 1 Result  “Connected to Ubnetwork=**RNC*”
q

To find out which RBS Type get 0


To connect to relevant RNC moshell **RNC1

You might also like