Intake-air Turbocharge System (MAZDA) Hệ thống nạp turbo tăng áp

Duration: 70 min College
Intake-air Turbocharge System (MAZDA)

Hệ thống nạp turbo tăng áp
Main content
Part 1 Introduction Turbocharge Engine
Part 2 Intake Turbocharge System (MAZDA)

Objectives
Part 3 Disadvantages and Solutions
PART 1 HISTORY DEVELOPMENT TURBOCHARGE
1885 1905 1962 1963 Late 20th cent 2012 Today
GM - Mazda 323 Luxury car Ford

Alfred Büchi Application
Chevrolet with Rolls-Royce Ecoboost
– Patented on fighter
Corvair turbocharge BWM Engine
Swiss aircraft
Monza Mercedes on Ford
engineer
Spyder Audi Fiesta
PART 1 FEATURES – INTAKE AIR TURBOCHARGE SYSTEM
– Hot wire-type mass air flow sensor with integrated intake air temperature sensor (similar to that of the
Mazda manifold injection system)
– Turbocharger with fixed geometry turbine and boost pressure control valve with pressure actuator
– Charge-air cooler
– Charge-air bypass valve
– Electronic throttle valve with hall-type accelerator pedal position sensor for Mazda6 MPS (similar to
that of the Mazda manifold injection system)
– Electronic throttle valve with inductive-type accelerator pedal position sensor for Mazda3 MPS
– Manifold absolute pressure sensor with integrated intake air temperature sensor (similar to that of the
Mazda manifold injection system)
– No variable intake-air system
– Variable swirl control system
PART 2
Texbook correlations COMPONENTS in SYSTEM
TurboCharger
Charge air cooler
Charge air bypass valve
Accelerator Pedal Position Sensor
Variable swirl Control system

Intake –– air
Intake air system
system PARTS LOCATION
1 Charge –air-cooler 7 Intake manifold
2 Turbocharger 8 VSC solenoid valve
3 Air cleaner 9 VSC vacuum actuator
4 Accelerator pedal 10 Electronic throttle valve
5 Resonance chamber 11 VBC solenoid valve
6 Charge-air bypass valve 12 VBC pressure actuator
Intake
ENGAGE – air system SYSTEM OVERVIEW
1 VSC vacuum actuator 9 Air cleaner
2 VSC solenoid valve 10 Flow limiter
3 Vacuum chamber 11 Turbocharger
4 One-way valve 12 Boost pressure control valve
5 Electronic throttle valve 13 VBC pressure actuator
6 Charge-air bypass valve 14 VBC solenoid valve
7 Charge-air cooler 15 VSC shutter valves
8 MAF/IAT sensor
Turbocharger
ENGAGE
1 Charge-air cooler 3 Turbine shaft
2 Turbine 4 Compressor
1 Compressor 5 VBC pressure actuator
Turbocharger
ENGAGE
2
3
Turbine
Boost pressure control valve
6
7
Turbine shaft
Boost pressure control valve open
4 Push rod
Turbocharger
ENGAGE
1 From PCM control relay 3 PCM
2 VBC solenoid valve
Turbocharger
ENGAGE Priciple
1 VBC solenoid valve energized 6 Turbocharger

2 VBC solenoid valve de-energized 7 Boost pressure control valve open
3 Boost pressure control valve closed 8 Intake-air flow
4 VBC pressure actuator 9 Exhaust-gas flow
5 VBC solenoid valve
Turbocharger
ENGAGE VBC Solenoid Valve Signal
Turbocharger
ENGAGE Strategy of the Boost Pressure Control / VBC
 The boost pressure control varies the boost pressure according to the
operating conditions of the engine. The PCM processes the incoming
information, calculates from it the target boost pressure and controls the
boost pressure control valve accordingly. The main parameters for
calculating the boost pressure are:
– Mass airflow (MAF)
– Engine speed (SPD)
– Throttle position (TPS)

 The PCM continuously monitors the boost pressure via the MAP sensor
signal. In order to protect the engine against overheating in case of a
malfunction, the PCM reduces the injection amount.
Charge
Intake air cooler
ENGAGE – air system
• The charge-air cooler (also termed as
intercooler) improves the charging efficiency of
the turbocharged engine, so that torque and
hence power output are increased accordingly.
• When the intake air is compressed in the
turbocharger, not only the pressure but also
the temperature of the air rises. As a result, the
density of the charge air decreases, leading to
a larger volume and hence to a lower cylinder
charge. In order to compensate this effect the
charge air is cooled accordingly.
• In addition, cooling the charge air lowers the
temperature in the combustion chamber,
preventing engine knocking.
1 Charge-air cooler 2 Charge-air bypass valve
Intake
Charge – air
ENGAGE air system
bypass valve
1 Throttle valve open 6 Throttle valve

2 Throttle valve closed 7 Charge-air bypass valve open
3 Charge-air bypass valve closed 8 Atmosphere pressure or excess pressure
4 Vacuum actuator 9 Vacuum
5 Valve
1 Rotor 4 Receiver coil

2 Printed circuit board 5 Excitation coil
3 Evaluation electronics
• One inductive sensor transmits a digital
voltage signal 0 V/12 V to the PCM. The
frequency of the signal is proportional to the
accelerator pedal position, i.e. the more the
accelerator pedal is pressed the higher the
frequency.
• The other inductive sensor supplies the
PCM with an analogue voltage signal between
0…5 V. The output voltage is proportional to
the accelerator pedal position, i.e. the more
the accelerator pedal is pressed the higher the
voltage. The PCM permanently compares the
signals of both sensors to monitor the APP
sensor for failure.
1 APP sensor 3 PCM
2 From PCM control relay
1 VSC vacúum actuator 3 Intake manifold

2 VSC shutter valves 4 VSC position switch
Variable Swirl Control system
The position of the

VSC shutter valves is
controlled by the
PCM, which activates
the VSC solenoid
valve by an ON/OFF
signal.
1 From PCM control relay 3 PCM
2 VSC solenoid valve
1 VSC solenoid valve energized 5 Air swirl

2 VSC solenoid valve de-energized 6 Cylinder
3 Intake port 7 VSC shutter valve open
4 VSC shutter valve closed
Variable swirl Control system VSC POSITION SWITCH
• The VSC position switch is

located at the VSC vacuum
actuator and detects the position
of the VSC shutter valves. When
the VSC shutter valves are open,
the switch closes and supplies the
PCM with a voltage signal of 0 V.
• The signal of the VSC position
switch serves to detect a
malfunction of the VSC system
1 VSC position switch 2 PCM
(such as VSC shutter valves stuck
closed etc.).
PART 3 DISADVANTAGES AND SOLUTIONS
Thanks you !
THANK YOU !

Intake-air Turbocharge System (MAZDA) Hệ thống nạp turbo tăng áp

Uploaded by

Copyright:

Available Formats

Intake-air Turbocharge System (MAZDA) Hệ thống nạp turbo tăng áp

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Intake-air Turbocharge System (MAZDA) Hệ thống nạp turbo tăng áp

Uploaded by

Copyright:

Available Formats

Duration: 70 min College

Intake-air Turbocharge System (MAZDA)

Part 1 Introduction Turbocharge Engine

Part 2 Intake Turbocharge System (MAZDA)

1885 1905 1962 1963 Late 20th cent 2012 Today

GM - Mazda 323 Luxury car Ford

Charge air cooler

Charge air bypass valve

Accelerator Pedal Position Sensor

Variable swirl Control system

1 VBC solenoid valve energized 6 Turbocharger

1 Throttle valve open 6 Throttle valve

1 Rotor 4 Receiver coil

1 VSC vacúum actuator 3 Intake manifold

The position of the

1 VSC solenoid valve energized 5 Air swirl

• The VSC position switch is

You might also like