Chapter 03

Ohm’s Law
© 2007 The McGraw-Hill Companies, Inc. All rights reserved.

Ohm’s Law
 Ohm's law states
that, in an electrical
circuit, the current
passing through
most materials is
directly proportional
to the potential
difference applied
across them.
Ohm’s Law Formulas
 There are three forms of
Ohm’s Law:
 I = V/R
 V = IR
 R = V/I
 where:
 I = Current
 V = Voltage
 R = Resistance
Fig. 3-4: A circle diagram to help in memorizing the Ohm’s Law formulas V = IR, I = V/R,
and R= V/I. The V is always at the top.
Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display.
The Current I = V/R
 I = V/R
 In practical units, this law
may be stated as:
 amperes = volts / ohms
Fig. 3-1: Increasing the applied voltage V produces more current I to light the bulb with
more intensity.
Practical Units
 The three forms of Ohm’s law can

be used to define the practical units
of current, voltage, and resistance:
 1 ampere = 1 volt / 1 ohm
 1 volt = 1 ampere × 1 ohm
 1 ohm = 1 volt / 1 ampere
Applying Ohm’s Law
? V
I R
20 V
1A
3A ?
6V ?
Applying Ohm’s Law V
? I R
20 V
20 V 4 I = =5A
4
1A
? 12  V = 1A × 12  = 12 V
3A
6V
6V ? R = =2
3A
Problem
 Solve for the resistance, R,

when V and I are known
a. V = 14 V, I = 2 A, R = ?
b. V = 25 V, I = 5 A, R = ?
c. V = 6 V, I = 1.5 A, R = ?
d. V = 24 V, I = 4 A, R = ?
Multiple and Submultiple Units
 Units of Voltage
 The basic unit of voltage is the volt (V).
 Multiple units of voltage are:
 kilovolt (kV)
1 thousand volts or 103 V
 megavolt (MV)
1 million volts or 106 V
 Submultiple units of voltage are:
 millivolt (mV)
1-thousandth of a volt or 10-3 V
 microvolt (μV)
1-millionth of a volt or 10-6 V
Multiple and Submultiple Units
 Units of Current
 The basic unit of current is the ampere (A).
 Submultiple units of current are:
 milliampere (mA)
1-thousandth of an ampere or 10-3 A
 microampere (μA)
1-millionth of an ampere or 10-6 A
3-5: Multiple and Submultiple Units
 Units of Resistance
 The basic unit of resistance is the Ohm (Ω).
 Multiple units of resistance are:
 kilohm (kΩ)
1 thousand ohms or 103 Ω
 Megohm (MΩ)
1 million ohms or 106 Ω
Problem
 How much is the current, I, in a 470-kΩ resistor if its
voltage is 23.5 V?
 How much voltage will be dropped across a 40 kΩ

resistance whose current is 250 µA?
3-6: The Linear Proportion between V and
I
 When V is constant:
 I decreases as R increases.
 I increases as R decreases.
 Examples:
 If R doubles, I is reduced by half.
 If R is reduced to ¼, I increases by 4.
 This is known as an inverse relationship.
3-7: Electric Power
 The basic unit of power is the watt (W).
 Multiple units of power are:
 kilowatt (kW):
1000 watts or 103 W
 megawatt (MW):
1 million watts or 106 W
 Submultiple units of power are:
 milliwatt (mW):
1-thousandth of a watt or 10-3 W
 microwatt (μW):
1-millionth of a watt or 10-6 W
3-7: Electric Power
 Work and energy are basically the same, with identical
units.
 Power is different. It is the time rate of doing work.

 Power = work / time.
 Work = power × time.
3-7: Electric Power
 Practical Units of Power and Work:
 The rate at which work is done (power) equals the
product of voltage and current. This is derived as
follows:
 First, recall that:
1 joule 1 coulomb
1 volt = and 1 ampere =
1 coulomb 1 second
3-7: Electric Power
Power = Volts × Amps, or

P=V×I
3-7: Electric Power
 Kilowatt Hours
 The kilowatt hour (kWh) is a unit commonly used for
large amounts of electrical work or energy.
 For example, electric bills are calculated in kilowatt

hours. The kilowatt hour is the billing unit.
 The amount of work (energy) can be found by

multiplying power (in kilowatts) × time in hours.
3-7: Electric Power
To calculate electric cost, start with the power:
 An air conditioner operates at 240 volts and 20
amperes.
 The power is P = V × I = 240 × 20 = 4800 watts.
 Convert to kilowatts:
4800 watts = 4.8 kilowatts
 Multiply by hours: (Assume it runs half the day)
energy = 4.8 kW × 12 hours = 57.6 kWh
Problem
 How much is the output voltage of a power supply if it
supplies 75 W of power while delivering a current of 5
A?
3-8: Power Dissipation in Resistance
 When current flows in a resistance, heat is produced

from the friction between the moving free electrons and
the atoms obstructing their path.
 Heat is evidence that power is used in producing

current.
3-8: Power Dissipation in Resistance
 The amount of power dissipated in a resistance may be

calculated using any one of three formulas, depending
on which factors are known:
 P = I2×R
 P = V2 / R
 P = V×I
Problem
 Solve for the power, P, dissipated by the resistance,
R
a. I = 1 A, R = 100Ω , P = ?
b. I = 20 mA, R = 1 kΩ , P = ?
c. V = 5 V, R = 150Ω , P = ?
d. V = 22.36 V, R = 1 kΩ , P = ?
 How much power is dissipated by an 8-Ω load if the

current in the load is 200 A?
3-9: Power Formulas
There are three basic power formulas, but each can be
in three forms for nine combinations.
Where:
P = Power V = Voltage I = Current R=Resistance
3-9: Power Formulas
 Combining Ohm’s Law and the Power Formula
 All nine power formulas are based on Ohm’s Law.
V = IR P = VI
I= V
R
 Substitute IR for V to obtain:
 P = VI
 = (IR)I
 = I 2R
3-9: Power Formulas
 Combining Ohm’s Law and the Power Formula
 Substitute V/R for I to obtain:
 P = VI
= V × V/ R
= V2 / R
3-9: Power Formulas
 Applying Power Formulas:
5A P = VI = 20 × 5 = 100 W
20 V 4 2
P = I R = 25 × 4 = 100 W
2
V 400
P= = = 100 W
R 4
Problem
 What is the resistance of a device that dissipates 1.2
kW of power when its current is 10 A?
 How much current does a 960 W coffeemaker draw

from the 120 V power line?
 What is the resistance of a 20 W, 12 V halogen lamp?

3-10: Choosing a Resistor
for a Circuit
 Follow these steps when choosing a resistor for a
circuit:
 Determine the required resistance value as R = V / I.
 Calculate the power dissipated by the resistor using any
of the power formulas.
 Select a wattage rating for the resistor that will provide
an adequate cushion between the actual power
dissipation and the resistor’s power rating.
 Ideally, the power dissipation in a resistor should never
be more than 50% of its power rating.
Problem
 Determine the required resistance and appropriate
wattage rating of a carbon-film resistor to meet the
following requirements. The resistor has a 54-V IR
drop when its current is 20 mA. The resistors available
have the following wattage ratings:
1/8 W, 1/4 W, 1/2 W, 1 W, and 2 W.
for a Circuit
 Maximum Working Voltage Rating
 A resistor’s maximum working voltage rating is the
maximum voltage a resistor can withstand without
internal arcing.
 The higher the wattage rating of the resistor, the higher

the maximum working voltage rating.
for a Circuit
 Maximum Working Voltage Rating
 With very large resistance values, the maximum
working voltage rating may be exceeded before the
power rating is exceeded.
 For any resistor, the maximum voltage which produces

the rated power dissipation is:
Vmax = Prating × R
 Exceeding Vmax causes the resistor’s power dissipation

to exceed its power rating
3-11: Electric Shock
 When possible, work only on circuits that have the
power shut off.
 If the power must be on, use only one hand when

making voltage measurements.
 Keep yourself insulated from earth ground.
 Hand-to-hand shocks can be very dangerous because

current is likely to flow through the heart!
3-12: Open-Circuit and
Short-Circuit Troubles
An open circuit has zero current flow.
3-12: Open-Circuit and
Short-Circuit Troubles
A short circuit has excessive current flow.
As R approaches 0, I approaches .

Chapter 03

Uploaded by

Copyright:

Available Formats

Chapter 03

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Chapter 03

Uploaded by

Copyright:

Available Formats

Ohm’s Law

© 2007 The McGraw-Hill Companies, Inc. All rights reserved.

 The three forms of Ohm’s law can

 Solve for the resistance, R,

 How much voltage will be dropped across a 40 kΩ

 Power is different. It is the time rate of doing work.

Power = Volts × Amps, or

 For example, electric bills are calculated in kilowatt

 The amount of work (energy) can be found by

 When current flows in a resistance, heat is produced

 Heat is evidence that power is used in producing

 The amount of power dissipated in a resistance may be

 How much power is dissipated by an 8-Ω load if the

 How much current does a 960 W coffeemaker draw

 What is the resistance of a 20 W, 12 V halogen lamp?

 The higher the wattage rating of the resistor, the higher

 For any resistor, the maximum voltage which produces

 Exceeding Vmax causes the resistor’s power dissipation

 If the power must be on, use only one hand when

 Keep yourself insulated from earth ground.

 Hand-to-hand shocks can be very dangerous because

You might also like