Scribd
Upload
176 views

Module 6 - Determinancy and Stability

Before analyzing the forces on a structure, its determinacy and stability must be established. A structure is determinate if its unknown forces can be determined using equilibrium equations alone; otherwise it is indeterminate. The degree of indeterminacy is the difference between the number of reactions and available equations. A structure is unstable if it has fewer reactions than equations or if reaction lines intersect at a single point.

Uploaded by

Peter Harold Maducdoc
Copyright
© © All Rights Reserved
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
176 views

Module 6 - Determinancy and Stability

Before analyzing the forces on a structure, its determinacy and stability must be established. A structure is determinate if its unknown forces can be determined using equilibrium equations alone; otherwise it is indeterminate. The degree of indeterminacy is the difference between the number of reactions and available equations. A structure is unstable if it has fewer reactions than equations or if reaction lines intersect at a single point.

Uploaded by

Peter Harold Maducdoc
Copyright
© © All Rights Reserved
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 20

DETERMINACY AND

STABILITY
“Before starting the force analysis of a structure, it is necessary to establish the
determinacy and stability of the structure.”
DETERMINACY AND STABILITY

EQUILIBRIUM EQUATIONS

It may be recalled from statics that a structure or one of its members is in


equilibrium when it maintains a balance of force and moment. In general this
requires that the force and moment equations of equilibrium be satisfied along
three independent axes, namely,

The principal load-carrying portions of most structures, however, lie in a single


plane, and since the loads are also coplanar, the above requirements for
equilibrium reduce to;
DETERMINACY AND STABILITY

 Whenever these equations are applied, it is first necessary to draw a free-


body diagram of the structure or its members. If a member is selected, it
must be isolated from its supports and surroundings and its outlined shape
drawn. All the forces and couple moments must be shown that act on the
member.

 It is also important to note that forces common to two members act with
equal magnitudes but opposite directions on the respective free-body
diagrams of the members.

 If the internal loadings at a specified point in a member are to be


determined, the method of sections must be used. This requires that a “cut” or
section be made perpendicular to the axis of the member at the point where the
internal loading is to be determined.
DETERMINACY AND STABILITY

 A free-body diagram of either segment of the “cut” member is isolated and


the internal loads are then determined from the equations of equilibrium
applied to the segment. In general, the internal loadings acting at the section
will consist of a normal force N, shear force V, and bending moment M.
DETERMINACY AND STABILITY

DETERMINANCY

 When all the forces in a structure can be determined strictly by using the
equilibrium equations, the structure is referred to as statically determinate.

 Structures having more unknown forces than available equilibrium equations


are called statically indeterminate.
For a coplanar structure there are at most three equilibrium equations for each
part, so that if there is a total of n parts and r force and moment reaction
components, we have;

n = the total parts of structure members.


r = the total number of unknown reactive force and moment components
DETERMINACY AND STABILITY

The degree of determinacy is the difference between the number of reactions


and the number of equations that can be made in any given structure

Degree of determinacy = Nos. of reactions – Nos. of equations

Note: An additional equation is made for every internal hinge present due to
the fact that the moment at this point will be equal to zero.

STABILITY

 A structure is geometrically unstable if there are fewer reactive forces than


equations of equilibrium; or if there are enough reactions, instability occurs if
the lines of action of these forces intersect at a common point.
DETERMINACY AND STABILITY
SAMPLE PROBLEM # 1
Classify each of the beams shown below as statically determinate or statically
indeterminate. If statically indeterminate, report the number of degrees of
indeterminacy. The beams are subjected to external loadings that are assumed to be
known and can act anywhere on the beams.
DETERMINACY AND STABILITY
SOLUTION:
DETERMINACY AND STABILITY
SAMPLE PROBLEM # 2
Classify each of the pin-connected structures shown in figure below as statically
determinate or statically indeterminate. If statically are subjected to arbitrary
external loadings that are assumed to be known and can act anywhere on the
structures.
DETERMINACY AND STABILITY
SOLUTION:
DETERMINACY AND STABILITY
SOLUTION:
DETERMINACY AND STABILITY
SAMPLE PROBLEM # 3
Classify each of the frames shown in figure below as statically determinate or
statically indeterminate. If statically indeterminate, report the number of degrees of
indeterminacy. The frames are subjected to external loadings that are assumed to
be known and can act anywhere on the frames.
DETERMINACY AND STABILITY
SOLUTION:
DETERMINACY AND STABILITY
SAMPLE PROBLEM # 4
Classify each of the structures in the figure below as stable or unstable. The
structures are subjected to arbitrary external loads that are assumed to be known.
DETERMINACY AND STABILITY
SOLUTION:
DETERMINACY AND STABILITY
SOLUTION:
DETERMINACY AND STABILITY

DETERMINANCY OF TRUSSES

b = the total parts of structure members.


r = the total number of unknown reactive force and moment components
j = the total number of joint connections
In particular, the degree of indeterminacy is specified by the difference in the
numbers (b + r) - 2j.
STABILITY
DETERMINACY AND STABILITY
SAMPLE PROBLEM # 5
Classify each of the trusses in the figure below as stable, unstable, statically
determinate, or statically indeterminate. The trusses are subjected to arbitrary
external loadings that are assumed to be known and can act anywhere on the
trusses.
DETERMINACY AND STABILITY
SOLUTION:
DETERMINACY AND STABILITY
SOLUTION:

You might also like