AREA [AREA COMPUTATION BY COORDINATES]

1. ENTER STARTING POINT COORDINATE AND PRESS THE BLUE “EXE” BUTTON

2. ENTER SECOND POINT COORDINATE AND PRESS THE BLUE “EXE” BUTTON

3. ENTER THIRD POINT COORDINATE AND PRESS THE BLUE “EXE” BUTTON

4. ENTER “0” [CONT] TO CONTINUE TO ENTER NEXT COORDINATE

5. CONTINUE TO KEY IN THE COORDINATES UNTIL THE LAST POINT [NOTE:

THE COORDINATES OF THE LAST POINT MUST BE SAME AS STARTING POINT]

6. ENTER “1” [END] IS TO COMPUTE THE AREA

N = 604.023
E = 555.157

N = 597.894
START & END POINT E = 626.406
N = 563.479
E = 516.938
AREA = 8711.9

N = 533.306
E = 645.280

N = 498.891
E = 573.559

GEO LEVEL SDN BHD – FX5800P USER GUIDE 1

 BM [REMOTE BENCH MARK]
1. ENTER THE REDUCED LEVEL OF THE TARGET POSITION [TGT RL]

2. ENTER THE ZENITH ANGLE [ZA]

3. ENTER THE MEASURED SLOPE DISTANCE [SLOPE DIST]

4. ENTER THE HEIGHT OF INSTRUMENT [INST HT]

5. THE REDUCED LEVEL OF THE INSTRUMENT POSITION WILL BE DISPLAYED

[RL=?]

INSTRUMENT
ZA =92 36’ 5”

SLOPE DIST = 50.753

TARGET
INST HT
= 1.45

RL = 104.788
TGT HT
= 1.6

TGT RL = 102.334

NOTE:
TO COMPUTE THE RL OF THE INSTRUMENT POSITION GIVEN THE INSTRUMENT HEIGHT,
TARGET HEIGHT, ZENITH ANGLE, SLOPE DISTANCE AND THE TARGET RL

GEO LEVEL SDN BHD – FX5800P USER GUIDE 2

CURVE [CIRCULAR CURVE SETTING-OUT]
1. ENTER THE COORDINATES OF THE TANGENT POINT, TP [N1 / E1]

2. ENTER THE TANGENT BEARING [BRG]

3. ENTER THE RADIUS OF THE CIRCULAR CURVE

4. ENTER THE COORDINATES OF THE SIDE SHOT POINT [N2 / E2]

5. ENTER ARC LENGTH WILL BE DISPLAYED [ARC=?] PRESS THE “EXE”

BUTTON TO CONTINUE

6. THE DISTANCE FROM THE SIDE SHOT POINT TO THE CURVE WILL BE
DISPLAYED [DIST=?]

7. REPEAT FROM STEP 4 AS MANY TIMES AS DESIRED

R
30

N2,E2
.0

N= 347.215
00

E= 357.857
9
7.05

N1,E1
TP
N= 344.631
E= 384.526

30.906
18.974
8”
6’0
4
15.499

2
23 N2,E2
=
G N= 323.025
BR E= 367.165

GEO LEVEL SDN BHD – FX5800P USER GUIDE 3

INTERSECT [INTERSECTION BY 2 KNOWN POINTS
1. ENTER THE COORDINATES OF POINT 1 [N1 / E1]

2. ENTER THE COORDINATES OF POINT 2 [N2 / E2]

3. ENTER THE BEARING FROM POINT 1 TO THE UNKNOWN POINT 3 [BRG1]

4. ENTER THE BEARING FROM POINT 2 TO THE UNKNOWN POINT 3 [BRG2]

5. THE COORDINATES OF POINT 3 WILL BE DISPLAYED [N3=? & E3=?]

6. REPEAT FROM STEP 1 AS MANY TIMES AS DESIRED

N3 = 593.715
E3 = 588.729

BR
”
’05

G 2
19

=3
06
= 19

38
’1 3”
G1
BR

N2 = 533.710
E2 = 669.416
N1 = 521.194
E1 = 563.306

NOTE:
1. COORDINATES OF POINTS 1 & 2 ARE KNOWN
2. BEARING 1-3 & 2-3 ARE KNOWN

GEO LEVEL SDN BHD – FX5800P USER GUIDE 4

 INV OFFSET
TO COMPUTE THE GIVEN THE CHAINAGE & OFFSET FROM A STRAIGHT

1. ENTER THE NORTHING OF THE OCCUPIED STATION [N]

2. ENTER THE EASTING OF THE OCCUPIED STATION [E]

3. ENTER THE BEARING OF THE STRAIGHT [BRG]

4. ENTER THE CHAINAGE [DISTANCE ALONG STRAIGHT] FROM THE

OCCUPIED STATION [CH]

ENTER A NEGATIVE VALUE IF THE POINT IS BEHIND THE OCCUPIED

STATION

5. ENTER THE OFFSET FROM THE STRAIGHT [OFFSET]. ENTER A

POSITIVE VALUE FOR OFFSET TO THE RIGHT & NEGATIVE VALUE FOR
OFFSET TO THE LEFT

6. THE COORDINATES WILL BE COMPUTED & DISPLAYED [OFFSET N &

OFFSET E]

7. REPEAT FROM STEP 5 AS REQUIRED

O
FF
SE
T
1 =
. 61 24
.8
64 ” 67
= 3
CH 1 0’5
2
=5
G
BR N = 144.253
N = 117.491 E = 1874.491
E = 1753.893
N = 124.280
E = 1808.204
O
FF
SE 0 66
T 7.
= -4
-2 =
7. CH
93
8

GEO LEVEL SDN BHD – FX5800P USER GUIDE 5

 INVERSE [COMPUTE BEARING & DISTANCE USING COORDINATES
1. ENTER COORDINATE OF THE STARTING POINT [N1-NORTHING /
E1-EASTING] & PRESS “EXE” BUTTON

2. ENTER COORDINATE OF THE STARTING POINT [N2-NORTHING /

E2-EASTING] & PRESS “EXE” BUTTON

3. THE BEARING & DISTANCE BETWEEN THE TWO POINTS WILL DISPLAYED

4. ENTER “0” [STAY] TO USE THE SAME STARTING POINT

5. ENTER “1” [JUMP] TO USE N2 & E2 AS THE STARTING POINT

6. REPEAT STEP 2 AS MANY TIMES AS REQUIRED

RADIATION [TO COMPUTE COORDINATES OF POINTS WITH 1 STARTING POINT]

1. ENTER COORDINATE OF THE STATION [N-NORTHING /
E-EASTING] & PRESS “EXE” BUTTON

2. ENTER BEARING OF THE RADIATED POINT & PRESS “EXE” BUTTON

3. ENTER THE DISTANCE OF THE RADIATED POINT & PRESS “EXE” BUTTON

4. THE COORDINATES OF THE RADIATED POINT WILL BE DISPLAYED

5. REPEAT STEP 2 AS MANY TIMES AS REQUIRED

EXAMPLE FOR INVERSE & RADIATION

N = 568.533
E = 613.510
4
59
2.
13

N = 536.895
0”

E = 642.739
30
’4

.4
52

1 47
58

6 ”
5 30’2
7

N = 500.000 88 06’02” 127.150 N = 504.214

E = 500.000 E = 627.080

GEO LEVEL SDN BHD – FX5800P USER GUIDE 6

 OFFSET
1. ENTER COORDINATE OF THE OCCUPIED STATION [N1 & E1] PRESS “EXE”

2. ENTER GRID BEARING IN “DDD.MMSS” FORMAT. Eg. 46.0058

3. ENTER COORDINATES OF THE SIDE SHOT POINT [N2 & E2] PRESS “EXE”

4. THE CHAINAGE [DISTANCE FROM OCCUPIED STATION TO THE SIDE SHOT

POINT WITH REFERENCE TO THE GRID BEARING] & OFFSET DISTANCE
WILL BE DISPLAYED

5. REPEAT STEP 2 AS MANY TIMES AS REQUIRED

O
SIDE SHOT FF
SE
N = 588.356 T
E = 695.177 =
-2
9.
04
9

’5 8”
OCCUPIED STN 00
N = 505.721 46 3
9
E = 651.389 8 .8
8
=
7 CH
73
1.
-4
=
CH
O
FF
SE
T
=

SIDE SHOT
-3
0

N = 454.741
.5
70

E = 642.587

GEO LEVEL SDN BHD – FX5800P USER GUIDE 7

 RESECTION [USING 3 KNOWNPOINT TO COMPUTE 1 UNKNOWN POINT]
1. ENTER POINT A COORDINATE [KNOWN POINT A ALWAYS ON LEFT SIDE]
PRESS “EXE”

2. ENTER POINT M COORDINATE [KNOWN POINT M ALWAYS ON MIDDLE]

PRESS “EXE”

3. ENTER POINT B COORDINATE [KNOWN POINT B ALWAYS ON RIGHT SIDE]

PRESS “EXE”

4. ENTER BEARING A [FROM UNKNOWN POINT TO POINT A] PRESS “EXE”

5. ENTER BEARING M [FROM UNKNOWN POINT TO POINT M] PRESS “EXE”

6. ENTER BEARING B [FROM UNKNOWN POINT TO POINT B] PRESS “EXE”

7. THE UNKNOWN POINT COORDINATE [NP & EP] WILL BE DISPLAYED

EXAMPLE 1 EXAMPLE 2

M A
N = 450.615 N = 430.047
E = 445.852 B E = 571.406
B
N = 408.690
N = 428.857
E = 522.736
E = 488.040
29 31”
337 3

6
10’

19
’5
2”
19

A
4’51”

N = 397.574
7”

P
4 21’1

E = 421.102
N = 391.276
E = 557.923
162

30
0
31’20”

42
’0
6”

P M
N = 360.899 N = 362.033
E = 482.864 E = 567.131

NOTE:
1. POINT P IS THE UNKNOWN POINT. POINT A, B & M WITH KNOWN COORDINATES

2. POINT A IS ALWAYS ON THE LEFT SIDE & POINT B IS ON THE RIGHT SIDE.
WITH RESPECT TO POINT M WHICH IS ALWAYS IN THE MIDDLE

GEO LEVEL SDN BHD – FX5800P USER GUIDE 8

ROAD SECANT
1. ENTER [BRG1] & PRESS “EXE” BUTTON

2. ENTER [BGR2] & PRESS “EXE” BUTTON

3. ENTER [W1] & PRESS “EXE” BUTTON

4. ENTER [W2] & PRESS “EXE” BUTTON

5. IT WILL DISPLAY INTERSECTION [BRG] & PRESS “EXE” BUTTON AGAIN.

IT WILL DISPLAY INTERSECTION [DIST]

EXAMPLE 1

BG2
BG1
52 34’40”
103 30’20”

W2
0

=2
.00

0. 00
= 20

BRG = 168 2’30”

0
W1

DIST = 22.152

EXAMPLE 2
BG2
80 49’08”
BG1
33 21’21”
W2 = 25.000

BRG = 161 16’17”

DIST = 25.351
W1
= 20.
000

GEO LEVEL SDN BHD – FX5800P USER GUIDE 9

 SOLAR
OPERATING INSTRUCTION
1. ZONE 1 – DATA ENTRY OF OBSERVED VALUES

1.1. ENTER CIRCLE LEFT [CL] HORIZONTAL READING TO REFERENCE OBJECT

[R.O]

1.2. ENTER 1ST CL HORIZONTAL READING TO SUN

1.3. ENTER 2ND CL HORIZONTAL READING TO SUN

1.4. ENTER 1ST CR HORIZONTAL READING TO SUN

1.5. ENTER 2ND CL HORIZONTAL READING TO SUN

1.6. ENTER CIRCLE RIGHT [CR] HORIZONTAL READING TO [R.O]

1.7. RESULTS OF “MEAN ON SUN” AND “MEAN ON R.O” WILL BE DISPLAYED

1.8. ENTER 1ST CL VERTICAL READING TO SUN

1.9. ENTER 2ND CL VERTICAL READING TO SUN

1.10 ENTER 1ST CR VERTICAL READING TO SUN

1.11 ENTER 2ND CR VERTICAL READING TO SUN

1.12 “MEAN ALT “ WILL BE DISPLAYED

1.13 FROM THE STAR ALAMARIC,ENTER THE REFLECTION & PARAX

CORRECTION VALUE

1.14 “TRUE ALT” WILL BE DISPLAY

2. ZONE 2 – COMPUTE THE LATITUDE & CONVERGENCE

2.1. ENTER NORTH COORDINATES OF THE STATION

2.2. ENTER NORTH COORDINATES OF THE ORIGIN

2.3. ENTER LATITUDE [LAT] OF THE ORIGIN

2.4. THE “LAT OF STATION” WILL BE DISPLAYED

2.5. ENTER EAST COORDINATES OF THE STATION

GEO LEVEL SDN BHD – FX5800P USER GUIDE 10

2.6. ENTER EAST COORDINATES OF THE ORIGIN

2.7. THE “CONVERGENCE” WILL BE DISPLAYED

3. ZONE 3 – COMPUTE THE GRID BEARING

3.1. ENTER DECLINATION [DEC] AT 0 HOUR U.T.

3.2. ENTER DEC AT 12 HOURS U.T.

3.3. ENTER THE U.T. AT TIME OF OBSERVATION

3.4. “ DEC” AT OBSERVATION WILL BE DISPLAYED

3.5. ENTER THE TRUE ALTITUDE [ALT] COMPUTE FROM “ZONE 1”

3.6. ENTER THE LATITUDE OF STATION AS COMPUTED FROM “ZONE 2”

3.7. THE “AZIMUTH” TO THE SUN WILL BE DISPLAYED

3.8. ENTER THE OBSERVED AZ [MEAN OF SUN] AS COMPUTED FROM “ZONE 1”

3.9. ENTER THE OBSERVED R.O [MEAN ON R.O] AS COMPUTED FROM “ZONE 1”

3.10 ENTER THE CONVERGENCE [CON] AS COMPUTED FROM “ZONE 2”

3.11 ENTER “GRID BEARING” WILL BE DISPLAYED

GEO LEVEL SDN BHD – FX5800P USER GUIDE 11

GEO LEVEL SDN BHD – FX5800P USER GUIDE 12
 SPIRAL [SPIRAL CURVE SETTING-OUT]
1. ENTER TANGENTIAL BEARING[TAN.BRG] OF THE STRAIGHT THAT
CONNECTS TO THE SPIRAL

2. ENETER THE COORDINATES OF THE TANGENT & SPIRAL INTERSECTION

POINT [TS.N & TS.E]

3. ENTER THE CHAINAGE OF THE TANGENT & SPIRAL INTERSECTION

POINT [TS.CH]

4. ENTER THE LENGTH OF THE SPIRAL CURVE [SPIRAL LENGTH]

5. ENTER THE RADIUS OF THE CONNECTING CIRCULAR [RADIUS]

6. ENTER “1” FOR RIGHT-HANDED [CLOCKWISE] CURVE OR “2” FOR

LEFT-HANDED [ANTI-CLOCKWISE]

7. ENTER THE CHAINAGE OF THE POINT TO BE SET-OUT ON THE SPIRAL [SO.CH]

8. THE COORDINATES [SO.N & SO.E] WILL BE COMPUTED & DISPLAYED.

9. REPEAT STEP 7 UNTIL ALL THE REQUIRED CHAINAGES ARE COMPUTED

CHAINAGE NORTHING EASTING

100 325.765 560.636
110 328.087 570.362
120 330.902 579.956
130 334.471 589.293
140 339.026 598.186 PT = 192.124
190

180 R =50.000

170

SPIRAL 160 SC = 162.124

LENGTH
TS = 92.124
= 70
N = 324.105
E = 552.937
120
60 70 80 90 100 110

56.700 TAN.BRG` = 77` 59’54”

GEO LEVEL SDN BHD – FX5800P USER GUIDE 13

TRANSFORM [COORDINATE TRANSFORMATION]
1. ENTER TRUE COORDINATES OF POINT 1 [N1 / E1]

2. ENTER PROJECT COORDINATES OF POINT 1 [Y1 /X1]

3. ENTER TRUE COORDINATES OF POINT 2 [N2 / E2]

4. ENTER PROJECT COORDINATES OF POINT 2 [Y2 /X2]

5. ENTER TRUE COORDINATES OF POINT ? [N? / E?]

6. ENTER PROJECT COORDINATES OF POINT ? [Y? / X?]

7. REPEAT FROM STEP 5 AS MANY TIMES AS DESIRED

N2 = 30107.676
E2 = 30021.131
Y2 = 572.696
X2 = 571.603

N = 30040.120
E = 29957.314
Y = 552.666 [ANS]
X = 480.856 [ANS]
N = 30054.548
E = 30018.142
Y = 530.426
X = 539.281

N1 = 29972.724
E1 = 29953.099
Y1 = 499.282
X1 = 439.503

GEO LEVEL SDN BHD – FX5800P USER GUIDE 14

 TRAVERSE MISCLOSE [WITH TRANSIT ADJUSTMENT
1. ENTER COORDINATE OF THE STARTING POINT [N1 – NORTHING, E1 –
EASTING]. IF THE COORDINATES ARE NOT NEEDED, THEN ENTER “0”
FOR THE NORTHING & THE PROGRAM WILL NOT PROMPT FOR ANY
MORE COORDINATES

2. PRESS THE “EXE” BUTTON

3. IF “OPEN LOOP” IS REQUIRED, ENTER THE ENDING COORDINATES AS

WELL [N2 & E2]. IF “CLOSED LOOP” IS REQUIRED,ENTER “0” FOR THE
NORTHING & EASTING WILL NOT BE PROMPTED

4. ENTER BEARING OF THE FORESIGHT READING & PRESS “EXE” BUTTON

5. ENTER DISTANCE OF THE FORESIGHT READING & PRESS “EXE” BUTTON

6. THE FORESIGHT COORDINATE WILL BE DISPLAYED, PRESS “EXE” TO

CONTINUE. IF THE STARTING COORDINATES ARE KEYED IN AS 0 [ZERO]
FOR THE NORTHING & EASTING, NO COORDINATE WILL BE DISPLAYED
AFTER EVERY BEARING & DISTANCE ENTRY

7. REPEAT STEP 2 ABOVE UNTIL THE LAST BEARING & DISTANCE HAVE
BEEN ENTERED

8. ENTER “0” FOR BOTH THE BEARING & DISTANCETO END THE TRAVERSE

9. THE MISCLOSE STATISTICS & THE AREA WILL BE DISPLAYED

10. PRESS “EXE” TO ADVANCE TO THE NEXT DISPLAYED STATISTIC

11. WHEN “0=DISPLAY 1=CONT 2=ADJUST 3=2ML” IS DISPLAYED ENTER

THE OPTION BY PRESSING THE NUMERIC KEYS AS REQUIRED
“0” TO REPEAT THE DISPLAY
“1” TO CONTINUE WITH THE NEXT ENTRY
“2” TO DO TRANSIT ADJUSTMENT
“3” TO COMPUTE 2 MISSING LINES

12. ENTER “2”TO BEGIN TRANSIT ADJUSTMENT

13. THE PROGRAM WILL PROMPT FOR THE BEARINGS & DISTANCE. YOU WILL
NEED TO RE-ENTER THE BEARINGS & DISTANCES AS PROMPTED

14. THE ADJUSTED COORDINATES [IF ENTERED] WILL BE DISPLAYED AFTER

EVERY ENTRY

15. ENTER “0” FOR THE BEARING & DISTANCE TO END DATA ENTRY
16. THE FINAL AREA WILL BE DISPLAYED
GEO LEVEL SDN BHD – FX5800P USER GUIDE 15
MISSING LINE [USING THE TRAVERSE PROGRAM]
1. ENTER “0” FOR BOTH THE NORTHING & EASTING OF THE STARTING
POINT. PRESS “EXE” BUTTON

2. ENTER BEARING OF THE FORESIGHT READING & PRESS “EXE” BUTTON

3. ENTER DISTANCE OF THE FORESIGHT READING & PRESS “EXE” BUTTON

4. REPEAT STEP 2 ABOVE UNTIL THE LAST BEARING & DISTANCE HAVE
BEEN ENTERED

5. ENTER “0” FOR THE BEARING & DISTANCE TO END DATA ENTRY

6. THE MISSING LINE INFORMATION WILL BE DISPLAYED

7. ALL OTHER INFORMATION DISPLAYED SHOULD BE IGNORED IF USING

THIS FUNCTION
ADJ
N = 587.763
E = 572.071
N = 587.762
E = 572.072

134 58’33”
43 40’35”
71.927
84.935

ADJ
START POINT N = 536.925
N = 526.333 E = 622.951
E = 513.417
DISPLAYED RESULTS: N = 536.924
END LINEAR MISCLOSE = 0.005 E = 622.953
N = 526.331 TOTAL DISTANCE = 396.106
E = 513.422 DELTA Y = 0.002
DELTA X = - 0.005 174 42’20
FLM = 1 IN 75366 76.584
AREA = 10360.2 SQ M
12’00”
333
83.059 N = 460.667
E = 630.020

ADJ
79.601 N = 460.668
53’23”
263 E = 630.018
N = 452.194
E = 550.871

ADJ
N = 452.195
E = 550.867

EXAMPLE OF TRAVERSE MISCLOSE COMPUTATION & ADJUSTMENT

GEO LEVEL SDN BHD – FX5800P USER GUIDE 16
 TWO MISSING LINE [USING THE TRAVERSE PROGRAM]
1. ENTER “THE COORDINATES FOR BOTH THE NORTHING & EASTING” OF
THE STARTING POINT OR ENTER “0” IF COORDINATES ARE NOT REQUIRED
THEN PRESS THE “EXE” BUTTON

2. ENTER BEARING OF THE FORESIGHT READING & PRESS “EXE” BUTTON

3. ENTER DISTANCE OF THE FORESIGHT READING & PRESS “EXE” BUTTON

4. REPEAT STEP 2 ABOVE UNTIL THE LAST KNOWN BEARING & DISTANCE
HAVE BEEN ENTERED

5. ENTER “0” FOR THE BEARING & DISTANCE TO END DATA ENTRY

6. THE MISSING LINE INFORMATION WILL BE DISPLAYED

7. ENTER THE 1ST BEARING [BX]

8. ENTER THE 2ND BEARING [BY]

9. THE TWO MISSING DISTANCE [DX & DY] WILL BE DISPLAYED

114 38’44”
77 22’37” 50.708
55.905

START
POINT

190 07’59”
53.462

BY = 353 59’09”
DY = 62.842

244 51’03”
BX = 290 51’46” 43.122
DX = 48.819
END
POINT

GEO LEVEL SDN BHD – FX5800P USER GUIDE 17

V-CURVE [VERTICAL CURVE SETTING OUT]
1. ENTER THE GRADIENT OF THE 1ST STRAIGHT IN % [GRAD M]

2. ENTER THE GRADIENT OF THE 2ND STRAIGHT IN % [GRAD N]. NOTE,

ENTER POSITIVE GRADIENT FOR UP SLOPE & NEGATIVE FOR DOWN
SLOPE

3. ENTER THE STARTING CHAINAGE [START CH]

4. ENTER THE LEVEL AT THE STARTING CHAINAGE [RL AT START]

5. ENTER THE ENDING CHAINAGE [END CH]

6. ENTER THE CHAINAGE THAT IS REQUIRED FOR SETTING-OUT [CH]

7. THE REDUCED LEVEL AT THAT CHAINAGE IS COMPUTED & DISPLAYED [RL]

8. REPEAT FROM STEP 6 AS REQUIRED

GRAD M = 1% GRAD N = -0.5%

START CH = 603.84
RL = 92.925 END CH = 738.84

CHAINAGE [D] REDUCED LEVEL [Z]

603.84 92.925
620 93.072
640 93.214
660 93.311
680 93.364
693.84 93.375
700 93.373
720 93.337
738.84 93.263

GEO LEVEL SDN BHD – FX5800P USER GUIDE 18