Basic Units of Computer

Architecture
Some of this material can be found in
Chapter 3 of Computer Architecture
(Carter)

CSIT 301 (Blum) 1

 Basic Units
There are three to five (depending on how you
count) basic units that make up a computer
• Arithmetic-Logic Unit
Central
(ALU) also known as
Processing
the datapath
Unit (CPU)
• Control (ROM)
• Memory (RAM)
• Input Input/Output
• Output (I/O)

CSIT 301 (Blum) 2

 Arithmetic/Logic Unit
• So much of what goes on inside a computer is just
holding of and/or movement of data, but the actual
computation (the manipulation of data to generate
“new” data) takes place in the ALU.
• Because data is represented in binary form (1’s and
0’s), the ALU is mainly comprised of logic gates,
circuits made from transistors that take inputs
(combinations of highs and lows) and produce
outputs (different combinations of highs and lows).
• Logic in which the output depends solely on the input
is called combinatorial.

CSIT 301 (Blum) 3

 Logic Gates and Boolean operators
• There is a correspondence between logic gates and
Boolean operators
– AND: when two or more Boolean expressions are ANDed, both
must be true for the combination to be true.
– OR: when two or more Boolean expressions are ORed, if either
one or the other or both are true, then the combination is true.
– NOT: takes one Boolean expression and yields the opposite of it,
true  false and vice versa.
– NAND: equivalent to an AND followed by a NOT
– NOR: equivalent to an OR followed by a NOT

CSIT 301 (Blum) 4

 ALU Cont. (Registers and
Accumulators)
• The ALU is not entirely combinatorial, it
also has some sequential components,
which can temporarily hold information.
• These little holding units are known as
registers.
• The primary registers associated with the
ALU go by the name accumulators.

CSIT 301 (Blum) 5

 Hierarchy of bit holders
• An electronic circuit that holds a single bit (a 1 or a 0) is
called a flip-flop.
• A small collection of flip-flops (8 or 16 or 32, etc.) is
called a register.
– A counter is a kind of register that in addition to holding bit
values can increment the number they represent.
– A shift register can hold a number as well as “shift” it.
• 00101101
• 01011010
• 10110100, etc.
• A collection of registers along with a way to address
(select out) a particular register is called memory.

CSIT 301 (Blum) 6

 Control Unit
• Control is responsible for determining what
action is to be performed on what data.
• If the action is a calculation, then control
will deliver the necessary data to the ALU,
inform the ALU what particular action is to
be performed, and then directs the output to
the appropriate location.

CSIT 301 (Blum) 7

 Control Cont.
• All of the other units of a computer have “control
inputs” that determine whether or not they are
active and what particular action they will
perform (if they can do more than one thing).
• Control takes code down to this lowest level of
making the appropriate control inputs high or low,
active or inactive.
– Not all devices are active when the control input is
high, some devices are “active low.”

CSIT 301 (Blum) 8

 Control is ROM
• At a high level, instructions may be arranged in
new and different orders (this after all is what
makes the computer programmable). But at the
low level the control sequences for a given
instruction do not change.
• Control sequences are thus made of Read Only
Memory (ROM) which are reprogrammed rarely
if at all.

CSIT 301 (Blum) 9

 Memory
• Memory consists of circuits whose primary
purpose is to hold information, but only
temporarily.
• Memory holds the data that the processor
has just acted on, is acting on or will soon
act on.
• When we use the term memory, we usually
mean Random Access Memory (RAM).

CSIT 301 (Blum) 10

 Memory
Memory is collection of holding cells (like registers).
Each cell has an address.

Address Value
0000 10010100
0001 01010010
0010 00101100
0011 01011100
0100 01100110
…

CSIT 301 (Blum) 11

 Random Access
• The data in any holding cell can be accessed
immediately for purposes of reading or writing by
supplying its address.
– Any random site can be “immediately” accessed.
– As opposed to sequential access in which one must
pass through all intermediate data between one’s
current location and the next desired location.
• VCR tapes are sequential;
• DVDs are random access (they support scene selection and
don’t have to be rewound).

CSIT 301 (Blum) 12

 Memory versus Storage
• Memory is a temporary holding place that
interacts fairly directly with the processor.
– Memory is volatile, the holding of the information
requires power. No power, no data held.
• Longer term holding of data not currently being
processed is done in storage (hard disks, floppy
disks, CDs).
• In this “basic units” picture of the computer
storage belongs to the Input/Output unit.

CSIT 301 (Blum) 13

 Input / Output
• The Input unit allows programs and data to be
entered into the computer.
• The Output unit allows the results of processing to
be exported to the outside world or other devices
or saved to be used later.
• This other device may be in the same case as the
processor, but it is output as far as the processor
and memory are concerned. Thus the hard drive
is both an input and an output device in this
picture.

CSIT 301 (Blum) 14

 Charles Babbage
• In the early 1800’s Charles Babbage designed
two machines: first the Difference Engine and
then the Analytical Engine that were mechanical
machines capable of performing calculations.
• The Difference Engine, most (but not all) of which
was built in Babbage’s time, was a special
purpose machine (i.e. it could only do particular
calculations).
• The Analytical Engine, which was designed but
not built in Babbage’s time, was more ambitious
in that it was programmable.
Who am I? What am I
doing here?
CSIT 301 (Blum) 15
 Babbage’s “Mill”

Built later based

on Babbage’s
specifications.

CSIT 301 (Blum) 16

 Babbage’s design
• Babbage’s design had the basic units we have
been describing.
• He conceived of it as having four components:
– the store (memory)
– the mill (computational unit, control + ALU)
– the input section (punched card reader)
– the output section (punched and printed output).

CSIT 301 (Blum) 17

 Babbage (Cont.)
• Babbage’s engines were entirely
mechanical and were comprised of gears
and cogs and such.
• The store held 1000 words of 50 decimal
digits used to hold variables and results.
• The mill (processor) could take data from
the store, add, subtract, multiply or divide
them, and return the answer to the store.

CSIT 301 (Blum) 18

 Babbage Input and Output
• The engine’s input was from punched cards.
– Punch cards started being used in industry (weaving)
since the early 1800’s. They disappeared in the 1980’s.
• The data input was not simply data from the
calculations but also data for instructions, making
the engine programmable.
• Instructions included being able to test whether a
number was positive or negative (an if).
• The engine’s output could be punched into a
copper engraver's plate producing a hardcopy.

CSIT 301 (Blum) 19

 Jacquard Loom Punch Card

CSIT 301 (Blum) 20

 Babbage’s project suffered scope creep

CSIT 301 (Blum) 21

 Fast forward a hundred years
• In the 1940’s the Electronic Numerical Integrator And
Computer (ENIAC) was built at the Moore School of the
University of Pennsylvania.
• It was completed in 1946 at the Moore School of the
University of Pennsylvania.
• The two driving forces behind it were John W. Mauchly
and J. Presper Eckert.
• There were other computers built during WWII notably the
one developed at Bletchley Park, UK to aid in their code
breaking mission.
Who am I? What am I
doing here?
CSIT 301 (Blum) 22
 ENIAC
• The ENIAC consisted of 17,480 vacuum tubes operating at
100,000 pulses per second.
– Think of a vacuum tube as a “souped up light bulb.”
• Vacuum tubes play the same role that transistors do in
modern computers (one can use them to “realize” logic gates)
– The switch from vacuum tubes to transistors marked a dramatic shift
in computer size and speed. People talk about the computers as
belonging to different “generations.” Moving to transistors is a
generational shift.
– The Pentium 4 processor introduced in 2000 had 42,000,000
transistors. The Itanium 2 in 2004 had 592,000,000 transistors. The
size and power requirements of vacuum tubes would have prohibited
these kind of numbers. The more recent Core i7 processor has a
transistor count is 731 Million.

CSIT 301 (Blum) 23

 Vacuum tube

CSIT 301 (Blum) 24

 Programming
• One drawback to the ENIAC was the way it
was programmed — with wires.
• A new program required rewiring.
• Mauchly, Eckert and John von Neumann
discussed designs of future computers (like
EDVAC) in which the programs
(instructions) would be stored in the
computer’s memory.

CSIT 301 (Blum) 25

 Early Programmers

CSIT 301 (Blum) 26

 Von Neumann Architecture
• John von Neumann was a consultant to the ENIAC project.
The team discussed changing the way computers were
programmed. Von Neumann publicized and popularized
these ideas.
• The instructions could be converted into numbers and
placed in memory along with the data. This is known as
the stored program concept.
• The combination of the basic units (ALU, control,
memory, input and output) and the stored program concept
give one the “von Neumann architecture.”

CSIT 301 (Blum) 27

CSIT 301 (Blum) 28
 Harvard architecture
• In the von Neumann architecture, the instructions
and data are held in the same memory.
• A variation on this, known as the Harvard
architecture, has the instructions and data held in
separate memories.
• A more modern variation on the Harvard
architecture is to have the data and instructions in
the same main memory but to place them in
separate caches.
CSIT 301 (Blum) 29
 John von Neumann

CSIT 301 (Blum) 30

 Micro-code (note: micro, not macro)
• What’s held in the memory is a low-level (assembly or
machine code) instruction which may have resulted when
some high-level language program was compiled.
• Below that is micro-code, the instructions at the lowest
level, those control signals fed directly to the hardware.
• Any higher-level instructions (including assembly) must
ultimately be converted to a lower level by control.
• A single machine-language instruction (like Load
Accumulator A) typically consists of several micro-code
instructions.
– Similarly a single high level instruction (such as principle =
principle*(1+interestRate) often consists of several assembly level
instructions.

CSIT 301 (Blum) 31

 Where is microcode stored?
• It used to literally be wired in (hence the term
“hard wired”).
• Typically it stored in ROM.
• If the code is stored in EEPROM, it can be
changed; this is known as microprogramming.
– EEPROM: Electrically Erasable Programmable ROM
• But this is something one does on a rare occasion
• Sometimes referred to as “firmware,” an
intermediate between software and hardware.
CSIT 301 (Blum) 32
 Machine language
• Machine language is a level above micro-code
• The instructions are numbers, which really are the
addresses of the micro-code instruction in ROM.
– Machine language is typically machine dependent. The
locations in ROM of the microcode vary from one
make of a computer to the next.
• A mnemonic version of machine language is
called assembly language.

CSIT 301 (Blum) 33

Getting down to hardware’s level
• High-level programs are translated into assembly
language or machine language by a compiler.
Assembly language programs are translated into
machine language by an assembler.
• Each processor has its own unique machine
language. Thus code must be rewritten or at least
recompiled to run on different processor
(different hardware).

CSIT 301 (Blum) 34

 A simple design
• Next we will show a computer design.
• It uses a very basic “bus architecture.”
• A bus is a shared path used to transmit and
receive information.

CSIT 301 (Blum) 35

 Bus
Keyboard
encoder

Input port 1 Accumulator

ALU Flags
Input port 2

Prog. counter TMP

Mem.Add.Reg. B

Memory C

MDR Output port 3 Display

Instr. Reg. Output port 4

CSIT 301 (Blum) 36

Control
 One Bus, Two Bus
• In this very primitive architecture, there is only one bus.
• Recall that memory can be thought of as values located at
addresses. Here the same bus is used for both data (values)
and addresses.
• This will make accessing memory (reading or writing) a
two-step process – deal with the address, then deal with the
data.
– Dealing with memory is always a two step process, but
in this architecture the one and only bus is tied up for
both step (no parallelism allowed).
• That is not the usual case. Most architectures have an
address bus and a data bus.

CSIT 301 (Blum) 37

 Input ports
• Keyboard encoder: converts key pressed
into corresponding string of bits (ASCII)
• Input port 1: where keyboard data is
entered, usually contains some memory (a
buffer) where data is held until the
processor is ready for it.
• Input port 2: where non-keyboard data is
entered.

CSIT 301 (Blum) 38

 Program counter
• The program counter points to the current line of
the program (which is stored in memory)
• This design shows arrows connecting the “PC” to
and from the bus, why?
– Sometimes the next instruction to be executed is not the
next line of code in memory, such as
• If
• Loops
• Subroutines, functions, etc.

CSIT 301 (Blum) 39

 MAR, MDR and Memory
• MAR (Memory Address Register) holds the
address of the memory location being read from or
written to
– Not necessarily same as program counter
• Memory (RAM): the place where data and
instructions are stored
• MDR (Memory Data Register) holds the data that
is being read from or written to memory
– Bi-directional connection to bus for reading and writing

CSIT 301 (Blum) 40

 Instruction Register
• Instruction register holds the instruction
that is currently being executed.
• A given line of assembly or machine
language code involves several micro-code
instructions, the instruction register holds
onto the instruction until all of the micro-
instruction steps are completed.
– It plays a role somewhat like the MAR but for
ROM instead of RAM
CSIT 301 (Blum) 41
 Controller/Sequencer
• Executes the program at the lowest level.
• Sends signals to the control pins of all the devices
involved.
• These lowest-level instructions are in ROM
• Each assembly-level instruction has a numerical
counterpart (machine language); the numerical
counterpart is the address of the microcode for
that instruction stored in ROM.
• Not shown, controller connects to everything

CSIT 301 (Blum) 42

 Accumulator and ALU
• Accumulator: register used in conjunction with
the ALU
• Data upon which arithmetic or logic operations
will eventually be performed is stored here; also
the results of these are stored here.
• ALU (Arithmetic Logic Unit) where operations
that change the data (as opposed to just moving it
around) are done.

CSIT 301 (Blum) 43

 Flags
• Flags are output from the ALU that are distinct
from data (data output goes to Acc. A)
• For example,
– A carry from an addition
– An indication of overflow
• These are needed for program control or to indicate possible
errors
– The result of a logical comparison (<, >, =)
• These are needed for control (ifs, loops, etc)

CSIT 301 (Blum) 44

 TMP, B and C
• TMP is the other register used in
conjunction with the ALU; the distinction is
that answers are generally sent to
Accumulator A
• B and C are additional registers used for
holding data temporarily
– They allow additional flexibility and reduce the
amount that must be written to memory.
CSIT 301 (Blum) 45
 Output ports
• Output port a connection to the “outside
world”
– Usually includes a buffer
– This design has one for displayed output and a
second for other output (e.g. storage)

CSIT 301 (Blum) 46

 Micro-code
• Let us now examine the steps involved in
the assembly (machine language)
instruction Load Accumulator A.

CSIT 301 (Blum) 47

 What do you mean by Load?
• There are different types of Loads
– Load
• Instruction and address
• Data at specified address to be put in Acc. A
– Load immediate
• Instruction and data
• Data in instruction sent directly to Acc. A
– Load indirect
• Instruction and address of address
• The data in the location indicated by the instruction holds another
address, and that address has the data to be placed in Acc. A

CSIT 301 (Blum) 48

 Fetch Cycle
• Address State: the value of the program counter
(which recall is the address of line of the program
to be performed) is put into memory address
register.
• Increment State: the program counter is
incremented, getting it ready for the next time.
• Memory State: the current line of the program is
put into instruction register (so Control knows
what to do).
CSIT 301 (Blum) 49
 Execution cycle (Load Acc. A)
• The remaining steps depend on the specific
instruction and are collectively known as the
execution cycle.
– Recall the instruction consisted of a load command and
an address. A copy of the address is now taken from
the instruction register over to the memory address
register.
– The value at that address is loaded into Acc. A.
– For the load command, there is no activity during the
sixth step. It is known as a "no operation" step (a "no
op" or "nop").

CSIT 301 (Blum) 50

 Bus
Keyboard
encoder

Input port 1 Accumulator

ALU Flags
Input port 2

Prog. counter TMP

Mem.Add.Reg. B

Memory C

MDR Output port 3 Display

Instr. Reg. Output port 4

CSIT 301 (Blum) 51

Control
 References
• Computer Architecture, Nicholas Carter
• Computer Organization and Design,
David A. Patterson and John L. Hennessey
• Digital Computer Electronics, Albert P.
Malvino and Jerald A. Brown
• http://en.wikipedia.org/wiki/Jacquard_loom

CSIT 301 (Blum) 52