CX INFO VIEW

 CALIBRATIONS.

10/11/20 1
10/11/20 2
10/11/20 3
10/11/20 4
10/11/20 5
10/11/20 6
10/11/20 7
10/11/20 8
10/11/20 9
10/11/20 10
 Abort
Message Calibration causes solutions
ID

X0001 invalid button pressed Header Other HHC key pressed than requested only press on the requested key

Place header f lat. Check if lateral tilt sensor is w orking

X0002 Lateral tilt sensor not in zero range Header Lateral tilt sensor not in zero position range
if installed : w orking range : 0.25-4.6 V

No calibration ACK received from Bosch module did not send a calibration
X0003 bosch
Header
ACK after 10 s
Check communication w ith bosch HHC module

X0004 Operation timed out ( after 3 m inutes) Header No user interaction for the past 3 minutes React faster to the calibration procedure

X0005 User stop Header User pressed ESC key

X0006 Pressure sensor fault Header Pressure sensor fault Check in diagnostics : w orking range : 2.5-7.48 V

X0007 Softw are undefined state Header Softw are got in a faulty state Restart calibration

autofloat m in and max values too less Autofloat sensor min and max position too Autofloat plates hanging loose ? Range of 40 %
X0008 difference
Header
less difference variation required.

X0009 Feeder postion not changing Header Feeder postion not changing Feeder angle sensor stuck at a certain position

X0010 Ground speed too high Header Ground speed too high Do not drive the machine w hile calibrating

Header / Max
X0011 Feeder angle sensor value invalid
stubble height
feeder anlge sensor w rong signal check if sensor is w ell adjusted (min 2,5V, max 7,5 V)

10/11/20 11
 Abort
Message Calibration causes solutions
ID
Header / Max
X0012 Bosch m odule offline
stubble height
Bosch module offline Make sure bosch module is still functioning

X0013 engine not running Header Engine rpm < 500 Start engine

X0014 feeder engaged Header feeder must be disengaged disengage feeder

X0015 autofloat left sensor fault Header autofloat left sensor fault if installed, check sensor : w orking range : 2.5 - 7.5 V

X0016 autofloat right sensor fault Header autofloat right sensor fault if installed, check sensor : w orking range : 2.5 - 7.5 V

pressure not dropping/increasing in

X0017 pressure not changing Header
first/second cal step
pressure must be low er/higher than 20/Max P+20 bar

10/11/20 12
10/11/20 13
10/11/20 14
10/11/20 15
10/11/20 16
 Abort
Message Calibration causes solutions
ID
drive the right distance (122 meters, 400 foot), make
the combine w as driven the w rong
X0060 invalid tire radius calculated Tire radius distance or to small/large tires are installed.
sure approximate tire radius is betw een 712mm and
1042mm

X0061 ground speed sensor error Tire radius ground speed sensor giving w rong signal Check sensor in diagnostics

10/11/20 17
10/11/20 18
10/11/20 19
10/11/20 20
10/11/20 21
10/11/20 22
Abort
Message Calibration causes solutions
ID
X0064 EEPROM voltage low,\ntoo risky Multifunctional handle
X0065 General EEPROM fault Multifunctional handle Voltage supply to print too low .
X0066 Invalid logical value Multifunctional handle Pot meter disconnected
X0067 Value outside range Multifunctional handle
X0068 Sensor signal invalid Multifunctional handle
X0069 Sensor is offline Multifunctional handle

X0070 Engine running MFH engine is running stop engine

10/11/20 23
10/11/20 24
10/11/20 25
10/11/20 26
Abort
Message Calibration causes solutions
ID
X0020 w rong concave position Concave position concave opening not correct pot meter giving invalid value : w orking range : 0.25-5.16

X0021 concave position sensor error Concave position concave position sensor error check sensor in diagnostics
check w ith the concave adjust button if the actuator is
X0022 Concave actuator error Concave position actuator error
still moving

10/11/20 27
10/11/20 28
10/11/20 29
 Abort
Message Calibration causes solutions
ID
upper sieve position sensor value upper sieve position sensor giving w rong
X0040 invalid
Upper sieve
signal
signal must be min 0,25V max 5V

X0043 upper sieve opening invalid Upper sieve upper sieve opening not 3mm w ithin limits open sieve to 3mm

10/11/20 30
10/11/20 31
10/11/20 32
 Abort
Message Calibration causes solutions
ID
low er sieve position sensor value low er sieve position sensor giving w rong
X0041 invalid
Lower sieve
signal
signal must be min 0,25V max 5V

X0044 low er sieve opening invalid Lower sieve low er sieve opening not 3mm w ithin limits open sieve to 3mm

10/11/20 33
10/11/20 34
10/11/20 35
10/11/20 36
 Abort
Message Calibration causes solutions
ID
lateral inclination sensor giving w rong
X0030 Lateral inclination sensor error Self levelling shoe
signal
signal must be min 0,25V max 5V

X0031 Shoe position sensor error Self levelling shoe shoe position sensor giving w rong signal signal must be min 0,25V max 5V

user tried a calibration on a option not

X0032 option not installed ALL options
installed on the combine
not implemented

X0033 Self-levelling shoe actuator error Self levelling shoe actuator error check w ith diagnostics if the actuator is still moving

X0034 Lateral inclination invalid Self levelling shoe combine not level w ithin limits put combine more level

X0035 Shoe position invalid Self levelling shoe shoe not level w ithin limits bring shoe more level

10/11/20 37
10/11/20 38
10/11/20 39
 Abort
Message Calibration causes solutions
ID
spreader plate position sensor value spreader plate position sensor giving
X0042 invalid
Spreader plates
w rong signal
signal must be min 0,25V max 5V

10/11/20 40
10/11/20 41
10/11/20 42
10/11/20 43
10/11/20 44
10/11/20 45
10/11/20 46
10/11/20 47
10/11/20 48
10/11/20 49
10/11/20 50
10/11/20 51
 Abort
Message Calibration causes solutions
ID
Groundspeed handle w as pulled back in neutral w hile
X0050 MF Handle position invalid
hydrostat calibrating
leave handle at its position

Groundspeed
X0051 MF Handle fault
hydrostat
MFH not calibrated or sensor fault Check in diagnostics

Groundspeed no ground speed pulses w ere detected

X0052 threshold determ ination timeout
hydrostat after a period of time.
Perform calibration w ithing time frame

Groundspeed
X0053 hydrostatic circuit fault
hydrostat
hydrostatic circuit is not w orkig OK check for shorts, open w ires

Groundspeed
X0054 engine not at high idle
hydrostat
engine at low idle throttle engine to high idle

Groundspeed
X0055 transm ission not in first gear
hydrostat
transmission not in f irst gear shif t transmission to first gear

Groundspeed
X0056 parking brake set
hydrostat
parking brake w as set during calibration remove parking brake

Groundspeed No supply voltage seen w ith handle out of check hydro supply voltage and/or neutral microsw itch
X0057 Supply voltage or microsw itch error
hydrostat neutral for correct operation

Groundspeed
X0058 Handle moved too fast
hydrostat
movement of handle too fast move handle slow er

10/11/20 52
10/11/20 53
10/11/20 54
10/11/20 55
 Abort
Message Calibration causes solutions
ID

10/11/20 56
10/11/20 57