Unit - V: Computer Control of Power Systems

Download as ppt, pdf, or txt
Download as ppt, pdf, or txt
You are on page 1of 18

UNIT – V

Computer Control of Power


Systems
COMPUTER CONTROL OF POWER SYSTEM
 The ability to perform operations at an unattended location from an attended
station or operating center and to have a definite indication that the operations
have been successfully carried out can provide significant cost savings in the
operation of a power system.

 Devices to control equipment remotely have been used for many years, and
the need for remote indication as well as control led to the development of
equipment that could perform the operations, monitor them, and report back
to the control center that the desired control action had been satisfactorily
affected. At the same time it is often important to transmit such information as
loads and bus voltages to an operating center.
SUPERVISORY CONTROL AND DATA AQUSITION /SCADA/

Supervisory control: is the SCADA function used to control commands to field


equipment (digital devices, set points) under the supervision of the RTUs, from
the operator or from another application, through a user-callable Application
Programming Interface (API).

This allows to operate


• two state devices, such as switching devices, with associated open/close
commands
• adjustable devises such as transformer tap changer with associated
raise/lower commands
• power units with set points, with interfacing with the AGC function
SCADA SYSTEM COMPONENTS
Almost all modern dispatch and operating centers of power systems are now
provided with at least some SCADA system equipment.

SCADA equipment has proven to be efficient and economical for power


system operations. It is a very effective aid for station operators, making it
possible for them to maintain relatively complete knowledge of conditions on
the portions of the system for which they are responsible.

The term Supervisory Control is normally applied to remote operation(control)


of such devices as motors or circuit breakers, and the signalling back
(supervision) to indicate that the desired operation actually has been affected
where as Data Acquisition means data is collected from RTUs, substation and
power plant’s digital control system, other control centers, manual entries,
automatic calculations, and any data from other applications.
Supervisory master units: is the heart of the system. All operator initiated
operations of an RTU are made through the master unit and are reported back to the
master from the RTUs. Modern supervisory master units consist of a digital computer
and equipment to permit communications between the master and the RTUs.

• In addition to computer, peripheral equipment necessary for the proper operation of the
system is provided. Such equipment consists of
1. control console

2. keyboards or other means of entering data and commands into the computer

3. CRTs or monitors

4. Printer to provide the operator at the master station with written messages of actions performed
by the master and of data obtained from RTUs.

5. Digital-to-Analogue converters to convert the digital data message information (on such items as
line current, bus voltage, frequency, power, and reactive power flow) to analogue form that can
be used to supply indicating or recording instruments.
Remote terminal units: are located at selected stations, ad are either
wired to perform certain preselected functions or, in modern units, equipped with
microcomputers which have memory and logic capabilities.

• The RTUs are also equipped with modems so that they can accept messages from the
master and signal back to the master that messages have been received and the
desired operations performed.

• Transducers in the remote units are used to convert such quantities as voltage,
current, watts and vars to direct current or voltage proportional to the measured
quantity, and then by means of analogue-to-digital converters convert the quantity to
digital form, used by the system for transmission from the remote to the master.
SCADA system applications: in addition to the remote supervisory control,
status monitoring, various other programs can be incorporated in such systems to improve
operations and minimize the manual effort required of power system operators. Some of
these are
a) Automatic generation control:- control systems that are responsive to frequency variations, cost
factors, transmission losses, etc
b) Security monitoring:- checking the limits of loading and other quantities in order to determine
whether the system is at or near at alert or emergency state.
c) Online load flow:- when sufficient information is telemetered to the master unit, a load flow
program can be developed to predict loading of lines and stations under selected future conditions
using actual operating data.

The reliability of a SCADA system is very important, and several means are used to
ensure maximum reliability for such system. Most master units are dual computers, with
one as a primary unit and the other on standby to take immediate control, usually
automatically, if primary unit should fail.
AUTOMATIC LOAD DISPATCHING

The Load Dispatch Department is the nerve centre for the operation, planning,
monitoring and control of the power system. Electricity cannot be stored and
has to be produced when it is needed. It is therefore essential that power system
is planned and operated optimally & economically. This is the main objective
of Load Dispatch Centre.
Major Functions of Load Dispatch Center:    
To ensure integrated operation of the power system.

To give directions and exercise supervision and control which is


required for integrated operation to achieve maximum economy and
efficiency in power system operation. 

Scheduling and Re-Scheduling of available resources for optimum and


economic operation of the power system.

To coordinate shutdowns for the Generating Units and Sub-station


equipment, including transmission lines taking into consideration
continuity of supply with quality.

System Restoration in a systematic manner in shortest possible


duration, following Grid Disturbances. 

Accounting of Energy handled by the State System. 

Compiling & Furnishing data pertaining to Power System Operation.


Thank u

You might also like