Engineering Measurements
Chapter three
Basic Electrical Measurements and Sensing Devices
And Variable conversion
elements
Home
Previous
Next
End
ngineering Basic Electrical Measurements and Sensing Devices
asurements
Forces of Electromagnetic Origin
Assume that we have a conductor in
a magnetic flux as shown. If a
current (i) passes through the wire, a
magnetic force (F) will be generated
and affect the wire. The value of this
force is:
F= BiL (1)
Where:
B is the magnetic flux density; Weber/m2
i is the current, Ampere.
L is the length of conductor in the
magnetic filed, m.
When using N of coils, the force become
F= NBiL (2)
ngineering Basic Electrical Measurements and Sensing Devices
asurements
Forces of Electromagnetic Origin
Consider the apparatus shown in Fig.
the relation between the spring
displacement (x) and the current an be
derived as:
Kx = BiL (3)
Rearrange Eq(3):
BL
x i
K
K
Or: i x
BL
As you can see, we can measure the current passing a conductor by letting this current
pass through the above configuration. Knowing B, L and K, what we have to do is
measure (x) and relate it to the current.
ngineering Basic Electrical Measurements and Sensing Devices
asurements
Analog and digital wave form
In many cases, the measured is a variable value with respect to time.
If the variation of the variable is continues all other the period of
measuring, the measured waveform is called analog (i.e. continuous
reading)
If the measuring is done at discrete points of time, then the wave
form is called digital.
ngineering Basic Electrical Measurements and Sensing Devices
asurements
Analog and digital wave form
ngineering Basic Electrical Measurements and Sensing Devices
asurements
Analog and digital wave form
ngineering Basic Electrical Measurements and Sensing Devices
asurements
Basic Analog Meters
Galvanometer
This device is used mainly to measure DC (direct current)
ngineering Basic Electrical Measurements and Sensing Devices
asurements
Basic Analog Meters
Galvanometer
Working principle:
A permanent magnet is used to produce the magnetic field
the telescope arrangement and expanded scale improve the readability of
the instrument.
When the measured current passes through the coil, it will produce magnetic
flux . The interaction between this flux and the flux from the permanent
magnet produce a force – moment system which rotate telescope. The
telescope position on a scale represent the value of the measured current.
ngineering Basic Electrical Measurements and Sensing Devices
asurements
Basic Analog Meters
iron-vane or moving-iron instrument
This device is used
mainly to measure AC
(alternating current)
Working principle:
When the AC is given to the fixed
coil, it produces a magnetic field.
This field exert a force on the
movable iron vane. The
displacement of the vane is
proportional to the magnitude of
the current.
ngineering Basic Electrical Measurements and Sensing Devices
asurements
Basic Analog Meters
DC voltmeter
Working principle:
a large resistor is placed in series
with the movement; thus, when the
instrument is connected to a voltage
source, the current in the
instrument is an indication of the
voltage.
ngineering Basic Electrical Measurements and Sensing Devices
asurements
Basic Input Circuits
Sending the
signal to some
place for
processing
operation
Convert the
Reduce the
physical Present the
noise of the
property to result data
measured
electrical
signal
signal
ngineering Basic Electrical Measurements and Sensing Devices
asurements
Basic Input Circuits
Consider a gas sensor, the resistance of which changes as a function of the gas
concentration surrounding the sensor.
Let the sensor be in series with a battery
The relation between the current, voltage and the resistance connection is:
E
i
R Ri
The maximum resistance of the
transducer is Rm, and the current
may be written in dimensionless
form as
i 1
Ei / Ri R / Rm Rm / Ri 1
As you can see, the relation
between the transducer
resistance and the current is
ngineering Basic Electrical Measurements and Sensing Devices
asurements
Basic Input Circuits
A modified circuit is shown in the figure. If the internal impedance of the
voltmeter is very large compared with the resistance in the circuit can be
represented as:
E
i
R Ri
This circuit is called ballast circuit
And with some dimensionless manipulation we can find:
E
iR
R / Rm Rm / Ri
Ei i Ri R R / Rm Rm / Ri 1
the We can relate the voltage to
resistance by the previous
equation.
It is more easy to measure voltage
than the current. However, the
relation here is also none linear.
ngineering Basic Electrical Measurements and Sensing Devices
asurements
Basic Input Circuits
The sensitivity (S) of a ballast circuit is defined as the rate of change in
transducer voltage (E) with respect to transducer resistance(R) and is given as:
dE Ei Ri
S
dR R Ri 2
The maximum sensitivity is found when
dS E R Ri
0 i 0 R Ri
dRi R Ri 3
for maximum sensitivity we should take Ri = R. But since R is a variable, we may select
the value of Ri only for the range of R where the sensitivity is to be a maximum.
ngineering Basic Electrical Measurements and Sensing Devices
asurements
Simple voltage divider
If the impedance of the meter is sufficiently high, the indicated voltage E will
be directly proportional to the variable resistance R; that is,
E R
for Ri R
Eo Rm
Considering the internal resistance of
the meter, the current drawn from the
voltage source is
Eo
i
Rm R Ri R / R Ri
E R / Rm
Eo R / Rm 1 R / Rm Rm / Ri 1
ngineering Basic Electrical Measurements and Sensing Devices
asurements
Example [1]
The output of a transducer with a total resistance of 150 is to be
measured with a voltage-sensitive circuit like that shown in Fig. . The
sensitivity is to be a maximum at the midpoint of the transducer.
Calculate the sensitivity at the 25 and 75 percent positions, assuming a
voltage source Ei of 100 V.
ngineering Basic Electrical Measurements and Sensing Devices
asurements
Example [1]
Solution
For maximum sensitivity at the midpoint of the range, we take
1
Ri R Rm 75
2
At the 25 percent position R = (0.25)(150) = 37.5, and the sensitivity is
calculated from
S
dE
Ei Ri
100 75
0.592V
dR R Ri 2 75 37.5 2
At the 75 percent position the corresponding sensitivity is
S
100 75 0.213 V
75 112 .5 2
ngineering Basic Electrical Measurements and Sensing Devices
asurements
Wheatstone bridge
The Wheatstone bridge is normally used for the comparison and measurement of
resistances in the range of 1 to 1 M.
The figure to the right shows an
example of typical Wheatstone.
the bridge consists of the four
resistances (R1, R2, R3, Rx), which are
arranged in a diamond shape. R2 and
R3 are normally known resistors,
R1 is a variable resistance, and Rx is the
unknown resistance value associated
with the transducer output.
ngineering Basic Electrical Measurements and Sensing Devices
asurements
Wheatstone bridge
Balanced and unbalanced bridge
Balanced bridges means that the
potential between points B and D
equal Zero when the voltage E is
applied to the circuit by closing
switch S1.
To examine the balanced bridge
condition, we can close switch S2
theand if
sensing device (G) reads no current then, the bridge is balanced and if it reads
some current then the bridge is unbalance
We can balance the bridge by varying R1 until (G) reads zero current.
ngineering Basic Electrical Measurements and Sensing Devices
asurements
Wheatstone bridge
Resistances relations
If the bridge is balanced bridge, then:
V1 V2 i1 R1 i2 R2 1
E E
Also i2 i3 i
and 1 xi 2
R2 R3 R1 Rx
Rearrange Eqs (1) and (2)
R2 R1 RR
R x 1 3 3
R3 Rx R2
Now we can determine the value of the unknown resistance Rx if
1. We guarantee that the bridge is balanced (G reading is zero)
2. The values of R1, R2 and R3 are known
ngineering Basic Electrical Measurements and Sensing Devices
asurements
Wheatstone bridge
Ratio arms
In bridges the term ratio arm is a used to describe two adjacent resistances ( for
example R2 and R3 or R1 and Rx)
Alternating current (AC) measurement
There are some bridge arrangements used to measure AC current.
In these bridges, the inductance and the capacitive elements are used to balance
the fluctuating in the signal.
Table 4.1 represent some of these circuits.
ngineering Basic Electrical Measurements and Sensing Devices
asurements
Unbalanced bridges
Again, unbalanced bridge is the bridge that has a current reading measured by
the sensing device G (Galvanometer).
The unbalanced bridges is helpful when measuring the dynamic signal behavior
specially when there is no time to achieve balanced condition.
If we are looking from the point of view of the galvanometer, the effective
resistance of the bridge (R) will be
R1 R4 R2 R3
R
R1 R4 R2 R3
ngineering Basic Electrical Measurements and Sensing Devices
asurements
Unbalanced bridges
If the unbalance is very small, the
resistance Rb will not affect the
effective resistance of the bridge fro
m the point of view of the
galvanometer.
E So:
g
ig
R Rg
Where:
1. ig is the current detected by the galvanometer
2. Eg is the galvanometer voltage and its found as:
R1 R2
Eg E
R
1 R4 R2 R3
ngineering Basic Electrical Measurements and Sensing Devices
asurements
Unbalanced bridges
For small unbalance we can also
assume that the galvanometer is not
connected and the resistance of the
total bridge circuit as seen from the
battery point of view is designated as
Ro and equal to:
Ro
R1 R4 R2 R
R1 R4 R2 R3
Now the voltage of the bridge circuit (E) determined as:
Ro
E Eo
Ro Rb
ngineering Basic Electrical Measurements and Sensing Devices
asurements
Example [2]
Example 4.4
DEFLECTION BRIDGE. The Wheatstone bridge circuit of Fig. 4.24 has ratio arms (R2
and R3) of 6000 and 600 . A galvanometer with a resistance of 70 and a sensitivity of
0.04 μA/mm is connected between B and D, and the adjustable resistance R1 reads
340 . The galvanometer deflection is 39 mm, and the battery voltage is 4V. Assuming
no internal battery resistance, calculate the value of the unknown resistance R.
Repeat for R2 and R3 having values of 600 and 60 , respectively.
ngineering Basic Electrical Measurements and Sensing Devices
asurements
Example [2]
Solution
the bridge is operated on the deflection principle
The galvanometer current is calculated from the deflection and sensitivity as
ig = (39)(0.04×10−6) = 1.56 μA
Now the resiatance are
Rb = 0 R1 = 340 R2 = 6000 R3 = 600 R4 = Rx Rg = 70
Also we have the voltage
E = 4.0V.
Eg R1 R2
To find R4, combine ig and E g E
R Rg R
1 R4 R2 R3
ngineering Basic Electrical Measurements and Sensing Devices
asurements
Example [2]
Solution
The relation become
R4
ER1 R3 ig Rg R1 R2 R3 R1 R2 R3
ig 1 R1 RG R2 R3 ER2
4 340 600 1.56 x106 70 340 6000 600 340 6000 600
R4
1.56 x101 340 70 6000 600 4 6000
R4 33.93
now when we take R2 = 600 and R3 = 60, we have R4 33.98
A.c. bridges
Bridges with a.c. excitation are used to measure unknown impedances.
As for d.c.
bridges, both null and deflection types exist, with null types being
generally reserved
for calibration duties.
Null-type impedance bridge
A typical null-type impedance bridge is shown in Figure below. The null
point can be
conveniently detected by monitoring the output with a pair of
headphones connected
via an operational amplifier across the points BD. This is a much cheaper
method of
null detection than the application of an expensive galvanometer that is
required for a
d.c. Wheatstone bridge.
29
Maxwell bridge
A Maxwell bridge is shown in Figure below. The
requirement for a variable inductance
box is avoided by introducing instead a second
variable resistance. The circuit requires
one standard fixed-value capacitor, two
variable-resistance boxes and one standard
fixed-value resistor, all of which are
components that are readily available and
inexpensive.
31
32
Example
Deflection-type a.c. bridge
Analysis of the circuit
Examples
ngineering Basic Electrical Measurements and Sensing Devices
asurements
Basic electrical elements
Amplifier
Amplifiers are electrical devices used to amplify the signal measured by
the transducer to reach a sufficient level of power
The value of the amplification is called the gain (A)
Ei Eo
A
Eo AEi
ngineering Basic Electrical Measurements and Sensing Devices
asurements
Amplifier
Types
There are two types of amplifiers:
1. Differential amplifier
2. Operational amplifier
Differential amplifier
A differential or balanced amplifier is a device that provides for two
inputs and an output proportional to the difference in the two input
voltages
is particularly useful for amplification and measurement of small
signals subjected to stray electric fields (typically line voltage at 60 Hz
and 115 V).
ngineering Basic Electrical Measurements and Sensing Devices
asurements
Amplifier
Operational amplifier (op-amp)
is a dc differential amplifier incorporating many solid-state elements in a
compact package and shown schematically in Fig
The (+) input is called the noninverting input because the output from
this source is in phase with the input. The inverting input (−) has the
opposite behavior; that is, the output resulting from that source is 180◦
out of phase with the input
ngineering Basic Electrical Measurements and Sensing Devices
asurements
Transformers
Transformers are used to match impedance in many experimental
situations.
Fig. show an ideal n-turn transformer
Mathematical relations
1 v2 v v is the voltage
v2 nv1 and i2 i1 n 2 1 Z 2 n 2 Z1 i is the current
n i2 i1 Z is the impedance
ngineering Basic Electrical Measurements and Sensing Devices
asurements
Signal Conditioning
Noise is present in all physical situations in which measurements are
attempted or information is conveyed.
In general, the noise in measurements is represented as a range of
frequency that is not related to the range of frequency of the
measured variable.
To reduce the noise, the range of measurement frequency must be
defined and the other ranges where the noise may lie is eliminated.
The elimination process is called filtering and the device used for this
prepuce is called filter.
ngineering Basic Electrical Measurements and Sensing Devices
asurements
Filters
Filters are electrical devices that pass a certain desired range or band
of frequencies.
The unwanted parts of the signal can be characterized as noise, but in
addition, there is also noise present in the frequency band of interest
Filter types
Low-pass circuits
High-pass circuits
Band-pass circuits
ngineering Basic Electrical Measurements and Sensing Devices
asurements
Filter types
permits the transmission of signals with frequencies
Low-pass circuits below a certain cutoff value with little or no
attenuation
High-pass circuits
allows the transmission of signals with frequencies
above a cutoff value
Band-pass circuits
permits the transmission of signals with frequencies
in a certain range or band while attenuating signals
with frequencies both above and below the limits
of this band
ngineering Basic Electrical Measurements and Sensing Devices
asurements
Filter types
ngineering Basic Electrical Measurements and Sensing Devices
asurements
The gain
A measurement of the degree of amplification or attenuation provided
by a circuit is given by its gain or amplification ratio.
output
Gain
input
In engineers language, we give the gain the decibel unit in spite of its
dimensionless nature . P2
Decibel dB 10 log
P1
where P1 and P2 are the input and output powers
Decibel in term of voltage and current
E2 I2
dB 20 log 20 log
E1 I1
