Shear Design of Beams: CE 470 - Steel Design Class

Shear Design of Beams
CE 470 - Steel Design Class
By:
Amit H. Varma
Shear Strength
 Beam shear strength is covered in Chapter G of the
AISC specifications. Both rolled shapes and welded
built-up shapes are covered.
 Rolled shapes is the focus here. Built-up shapes,
commonly referred to as plate-girders are beyond
the scope of our course.
 Consider the behavior of beams in shear
Shear Strength
 The web will completely yield long before the
flanges begin to yield. Because of this, yielding of
the web represents one of the shear limit states.
 Taking the shear yield stress as 60% of the
tensile yield stress.
V
f v  n  0.6 Fy
Aw
Vn  0.6 Fy Aw
 This will be the nominal strength in shear

provided there is no shear buckling of the web.

 Shear buckling of the web depends on its h/tw ratio.
 If the ratio is too large, then then web can buckle
in shear elastically or inelastically.
Shear Buckling
Elastic shear
Shear
buckling
yielding
Shear Buckling
 for unstiffened webs with h / t w  260

kv  5
 for stiffened webs
5
kv  5 
( a / h) 2
2
 
 260 
 5 when a/h  3.0 or a/h   

 h   
  t w  
where a  clear distance between transverse stiffners, in.
Shear Design Equations
 area of web, the overall depth times the web thickness,,
=
h= for rolled shapes, the clear distance between flanges less the
fillet or corner radii, in.
= for built-up welded sections, the clear distance between the
flanges, in.
= for built-up bolted sections, the distance between fastener
lines, in.
= for tees, the overall depth, in.
= thickness of web, in.
 web plate shear buckling co-efficient,, is determined as follows:
The
 For webs without transverse stiffeners and with
except for the stem of tee shapes where

 For webs with transverse stiffeners
(G2-6)
=5 when a/h >3.0 or a/h >
where
a= clear distance between transverse stiffeners, in.
2.
 Transverse Stiffeners:
Transverse stiffeners are not required where , or where the available
shear strength provided in accordance with Section G2.1 for is greater
than the required shear strength.
The moment of inertia, , of the transverse stiffeners used to develop
the available web shear strength, as provided in Section G2.1, about an
axis in the web center for stiffener pairs or about the face in contact
with the web plate for single stiffeners, shall meet the following
requirement
(G2-7)
where
(G2-8)
and b is the smaller of the dimensions a and h.
Block Shear Failure of Beam
 Block shear failure was considered earlier in
tension member connections.
 To facilitate the connections of beams to other
beams so that the top flanges are at the same
elevation, a short length of the top flange of one
of the beams may be cut away, or coped.
 If a coped beam is connected with bolts as
shown, segment ABC will tend to tear out.
Block shear failure of beam ends
 The applied load in the case of the beam will be
the vertical reaction, so shear will occur along
line AB and there will be tension along BC. Thus,
the block shear strength will be a limiting value
of the reaction.
 Failure is assumed to occurred by rupture
(fracture) on the tension area and rupture or
yielding on the shear area.
 Rn = 0.6 Fu Anv + Ubs Fu Ant  0.6 Fy Agv + Ubs Fu Ant
 Where, phi =0.75
Example
 Determine the maximum reaction, based on
block shear, that can be resisted by the beam
shown below. Treat the bolt end distance of 1.25
in. as standard.
 The effective hole diameter is 3/4 + 1/8 = 7/8 in.

 The shear areas are:
 Agv = tw (2+3+3+3) = 0.30 (11) = 3.3 in2
 Anv = 0.300 [11 -3.5 (7/8)] = 2.381 in2
Block shear example
 The net tension area is:
 Ant = 0.300 [1.25 - 1/2 (7/8) ] = 0.2438 in2
 Since the block shear will occur in a coped beam
with standard bolt end distance Ubs = 1.0.
 Rn = 0.6 Fu Anv + Fu Ant = 108.7 kips
 With an upper limit of
 Rn = 0.6 Fy Agv + Fu Ant = 114.85 kips
 Therefore, nominal block shear strength = 108.7

kips
 Factored block shear strength for design = 0.75 x
108.7 = 81.5 kips.

Shear Design of Beams: CE 470 - Steel Design Class

Uploaded by

Copyright:

Available Formats

Shear Design of Beams: CE 470 - Steel Design Class

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Shear Design of Beams: CE 470 - Steel Design Class

Uploaded by

Copyright:

Available Formats

Shear Design of Beams

CE 470 - Steel Design Class

 This will be the nominal strength in shear

 for unstiffened webs with h / t w  260

except for the stem of tee shapes where

 The effective hole diameter is 3/4 + 1/8 = 7/8 in.

 Therefore, nominal block shear strength = 108.7

You might also like