Help

ABB industrial drives, Control Panel

ACS800 Operation

E-
learning
© Copyright 03/18/20 ABB.
All rights reserved.
 Help

Objectives

Upon the completion of this module,

you will be able to

 Control the drive with the control panel

 Read and select the actual values on the display
 Set up parameters with the panel
 Read alarm and fault messages
© Copyright 03/18/20 ABB.
All rights reserved. - 2 -
 Help

Control panel CDP 312R

 The CDP 312 R control panel is fully

compatible with the previous control
panel version - CDP 312
 The functionality of the panel
depends on the Drive SW version
and the control panel itself
 Full functionality is achieved when
the combination of ACS800 and
CDP 312R is used
© Copyright 03/18/20 ABB.
All rights reserved. - 3 -
 Help

Controlling the Drive

 Device used for controlling and

programming
 Can be attached directly to the module or
door of the cabinet
 The keys are flat, labeled push-buttons
 LCD display: 4x20 characters
© Copyright 03/18/20 ABB.
All rights reserved. - 4 -
 Controlling the Drive Help

Display

 Row 1: Drive status

– ID Number of the selected Drive 1
2
– Panel Status: 3
 L = Local 4

 R = Remote
– Rotational Direction:
  = Forward
  = Reverse
– Value of the reference
– Run status:
 I = Run
 0 = Stop
© Copyright 03/18/20 ABB.

 ' ' = No start permission.

All rights reserved. - 5 -

 Rows 2-4: Actual Signal names and values

 Controlling the Drive Help

Operation Mode Keys

 Operation mode keys

– Actual (for displaying operational
data or Actual Signals)
– Parameter (to display and edit
parameter names and values)
– Function (to enter assistants and
Upload/Download parameters)
– Drive (for assigning Drive ID
Numbers on a network)
© Copyright 03/18/20 ABB.
All rights reserved. - 6 -
 Controlling the Drive Help

Drive Control Keys

 Drive Control keys

– Start - used to start the Drive
– Stop - used to stop the Drive
– REF - used to set drive reference
value from keypad
– Forward and Reverse keys - used to
change the rotational direction of the
motor
– LOC/REM - used to change drive
control location between Local at the
keypad and the Remote control
© Copyright 03/18/20 ABB.
All rights reserved. - 7 -

– RESET - used to reset a fault of the

drive
 Help

Reading Actual Values

 This mode contains two displays, the

Actual Signal Display and the Fault
History Display
 The Actual Signal Display is shown
first whenever the Actual Signal
Display Mode is entered
 The actual display shows the following
information: Status row

– Status row Actual signals

– Three selectable actual signals

© Copyright 03/18/20 ABB.
All rights reserved. - 8 -
 Help

Setting Up Parameters
 The Parameter Mode is used for changing
the ACS800 parameters
 The display panel will show the following
information:
– Status row
– Group number and name
– Parameter number and name
– Parameter value
 Changing parameters
– Group can be changed with double arrows
– Number can be changed with single arrows
© Copyright 03/18/20 ABB.

– Value can be changed using the arrows and

All rights reserved. - 9 -

ENTER key
 Help

Reading Alarm & Fault Messages

 When a fault or warning occurs the Fault

Display appears
 The panel display will show the following
information:
– Status row
– Drive Type
– FAULT or WARNING message
– Name and number of Warning or Fault.
 Fault can be resetted with RESET button or
with a PC Tool
© Copyright 03/18/20 ABB.
All rights reserved. - 10 -
 Help

Fault History Display

 Select Fault History Display by pressing

ACT button and then double- arrow button
 The display panel will show the following
information:
– Sequential number of the event, 1 being the
most recent event
– Name of warning or fault
– Event sign
+ indicates that the event is active
- indicates that the event is deactivated
– Total Power On time
© Copyright 03/18/20 ABB.

 By pressing the arrow keys you can scroll

All rights reserved. - 11 -

the Fault History of the drive

 Help

Function Mode

 The Function Mode is used to select

special functions
– Drive assistants (only in single drives)
With drive assistants the user can start
a guided procedure for adjusting the
drive settings
– Parameter Upload / Download
– Setting the contrast of the Control
Panel display
 Selecting a function
– Page can be changed with double
arrows
© Copyright 03/18/20 ABB.
All rights reserved. - 12 -

– Row can be changed with single arrows

– Function can be selected using the
ENTER key when cursor on the line
 Help

Drive Mode
 Drive mode display contains basic
information of the drive:
– Drive type
– Drive software version and test date
– Drive ID-number
 Status Display symbols
Drive stopped, direction forward
Drive running, direction reverse
Drive has tripped due to a fault
 For normal use, the functions available in
the Drive Selection Mode are not needed
© Copyright 03/18/20 ABB.
All rights reserved. - 13 -