Derivative Controllers

CONTROL SYSTEMS ASSIGNMENT

Submitted by:
Netto Varghese- R16me175
 Introduction

System – An interconnection of elements and devices for a

desired purpose.
Control System –An interconnection of components forming a
system configuration that will provide a desired response.

Process –The device, plant, or system under control. The input

and output relationship represents the cause-and-effect
relationship of the process.

2
 Types of Control System

Open-Loop Control Systems utilize a controller or control actuator to obtain

the desired response.

Closed-Loop Control Systems utilizes feedback to compare the actual

output to the desired output response.

3
Multivariable Control System: Systems with more than one control loop
are known as Multi Input Multi Output (MIMO) or Multivariable control
Systems.

Intelligent Control Systems: Intelligent control is a class of control

techniques that use various artificial intelligence computing
approaches like neural networks, Bayesian probability, fuzzy logic,
machine learning, evolutionary computation and genetic algorithms.

4
Requirements of a Good Control System
• Accuracy: defines the limits of the errors made when the instrument is
used in normal operating conditions. To increase accuracy of any
control system error detector should be present in control system.

• Sensitivity: A control system should be sensitive to the input only.

• Noise: A good control system should be able to reduce the noise

effect.

• Bandwidth: Bandwidth should be large as possible for frequency

response of good control system.

• Speed: A good control system possesses high speed. The transient

period for such system is verysmall.

• Oscillations: A small numbers of oscillation or constant oscillation of

output tend to system to be stable.
5
Controllers :

A controller is one which compares controlled values with the desired

values and has a function to correct the deviation produced.

Type of Controllers :

1. Proportional Controller (P)

2. Proportional Derivative Controller (PD)

3. Proportional Integral Controller (PI)

4. Proportional Integral Derivative Controller (PID)

6
Proportional Controller

In a proportional controller the output (also called the actuating/control

signal) is directly proportional to the error signal.

Control signal =Kp X ErrorSignal

If the error signal is a voltage, and the control signal is also a voltage,
then a proportional controller is just an amplifier.
7
Properties:

In a proportional controller, steady state error tends to depend inversely

upon the proportional gain, so if the gain is made larger the error goes
down.
SSE =1/(1 +KpG(0))

Proportional controller helps in reducing the steady state error, thus makes
the system more stable.

Slow response of the over damped system can be made faster with the
help of thesecontrollers.

Shortcomings:

P controller has the advantage of reducing down the steady state error of
the system , but along with that it also has some serious disadvantages.

8
 Disadvantages of PController

1. Due to presence of these controllers we some offsets in the system.

2. Proportional controllers also increase the maximum overshoot of the

system.

3. It directly amplifies process noise.

To avoid these errors and to make the controller more accurate and
practical, we use the advanced and modified version of it known as the
Proportional Integral Controllers (PI) and Proportional Derivative Controllers
(PD).

9
Proportional Derivative (PD) Controller:

This kind of action gives an output which is proportional to the derivative or

the rate of change of the error.

Derivative action could not be used alone in practice. This is because its
output is only related to the rate of change of the error. The error could be
huge, but if it were unchanging, the controller would not give any output.
Thus although it is theoretically possible, it is practically impossible.

Derivative control is usually found in combination with proportional control,

to form so-called P+D.

10
Properties/Advantages of PD Controller:

OD =- kD dEr / dt
where
OD =output derivative controller
kD =derivative gain or action factor of the controller
dEr =deviation change over time sample dt
dt =time sample

• Derivative part in the PD controller reduces the overshoot and improves

the transient stability of the control system.

• It reduces the time constant of the system and thus making system
faster.

• It has no effect on the steady state error (derivative part) and on the
offset caused by the P controller.
11
Proportional Integral (PI)Controller:

As the name suggests in integral controllers the output (also called the
actuating signal) is directly proportional to the integral of the error signal.

Integral Controllers used alongside with proportional controllers are called PI

controllers.

PIcontroller equation:

Just like PD controller it also has a parallel connection of P and Icontrollers.

12
Properties/Advantages of PIcontroller:

• Output is proportional to the integral of the input signal.

• As the integrator is involved, it increases the type of the system.

• As the type of the system increases, it reduces SSE and hence improves
accuracy.

• Integral action enables PI controllers to eliminate offset, a major weakness

of a P-only controller. Thus, PI controllers provide a balance of complexity
and capability that makes them by far the most widely used algorithm in
process control applications.

• As the type of the system is increased, there is some negative impact over
the stability of thesystem.

13
Proportional-Integral-Derivative (PID)Controller:

PID controller involves all the three controllers studied earlier i:e P, PD and
PI connected in parallel.

PID controller involves the parallel combination of these 3 controllers and

the output equation is proportional to the derivative as well as integral of
the error signal.

14
The Characteristics of P, I,and D controllers
• A proportional controller (Kp) will have the effect of reducing the rise
time and will reduce, but never eliminate, the steady-state error.

• An integral control (Ki) will have the effect of eliminating the steady-state
error, but it may make the transient response worse.

• A derivative control (Kd) will have the effect of increasing the stability of
the system, reducing the overshoot, and improving the transient
response.

All design specifications can be reached with the PID controller and 100%
desired conditions can be achieved .

15
Effect of increasing the individual gains:

16
Tips for Designing a Derivative Controller

1.Obtain an open-loop response and determine what needs to be

Improved.

2.Add a proportional control to improve the rise time.

3.Add a derivative control to improve the overshoot.
4.Add an integral control to eliminate the steady-state error.
5. Adjust each of Kp, Ki, and Kd until you obtain a desired overall response.

17