Chapter 1: Introduction

Kobid Karkee
[email protected]
Kantipur Engineering College
Dhapakhel, Lalitpur

1
 Course Structure
• Theory: 80
– Chapter 1: Introduction 8 marks
– Chapter 2: RF and M/W Transmission Lines 10 marks
– Chapter 3: RF and M/W Network Theory and Analysis 8 marks
– Chapter 4: RF/MW Components and Devices 10 marks
– Chapter 5: Microwave Generator 8 marks
– Chapter 6: RF Design Practice 20 marks
– Chapter 7: Microwave Antennas and Propagation 8 marks
– Chapter 8: RF/MW Measurements 8 marks

• Practical: 25

2
 Reference Books
1. Microwave Electronics- K.C Gupta, Tata McGraw Hill
2. Microwave Engineering- A.K. Gautam, S.K.Kataria &
Sons
3. Microwave Techniques-D.C. Agrawal, Tata Mc Graw-hill
4. Microwave Devices and Circuits-Samuel Y. Liao, PHI 3rd
Edition,1994
5. Microwave Engineering-David M. Pozar, 2nd Edition,
Newington CT: 1997
6. Engineering Electromagnetic-W.H. Hyatt, McGraw-Hill
Book Company
7. Electronic Transmission Technology: Lines, Waves and
Antennas-William Sinnema, Prentice Hall

3
 RF/Microwave
• RF is a rate of oscillation in the range around
3KHz to 300GHz, which corresponds to the
frequency of radio waves and the alternating
currents which carry radio signals.
• Microwave: is not meant to suggest a wavelength
micrometer, have smaller wavelength compared
to radio broadcasting.
• Microwave Frequency Range: 300MHz-300GHz
• Wavelength: 1mm – 1m
• Both includes UHF (0.3-3GHz), SHF (3-30GHz)
and EHF (30-300GHz) signals.

4
Electromagnetic Spectrum

5
6
IEEE Microwave Frequency Band

7
Microwave System

8
 Microwave Sources
• High power microwave sources use specialized
vacuum tubes to generate microwave.
• Operate on the principle of ballistic motion of
electrons in a vacuum under the influence of
controlling electric or magnetic field.
• Includes magnetron, klystron, travelling wave
tube (TWT) and gyrotron.
• These devices work in the density modulated
mode (work on the basis of clumps of electrons
flying ballisticially through them, rather than
using a continuous stream of electrons).
9
• Lower power microwave sources use solid
state devices such as the FET, tunnel diodes,
Gunn diodes and IMPATT diodes.
• MASER is a solid state device which amplifies
microwave using similar principle to the
LASER, which amplifies higher frequency
light waves.

10
Advantages of using higher frequency
• Larger instantaneous bandwidth for much
information
• Higher resolution for radar imaging and sensing
• Less interference by near by application
• Higher speed for digital communication, signal
processing and transmission
• Less crowded spectrum
• Difficulty in jamming (military application)

11
Disadvantages of using high frequency
• More expensive component
• Higher atmospheric loss
• Reliance in GaAs technology rather than Si
technology
• Higher component losses, lower output power
from active devices

12
 Microwave Applications
• Communication
– Before the advent of fiber-optic transmission, most long-
distance telephone calls were carried via networks of
microwave radio relay links using FDM.
– Wireless LAN protocols, such as Bluetooth and the IEEE
802.11 specifications, also use microwaves in the 2.4 GHz
ISM band.
– Wireless internet access IEEE 802.11a uses microwaves at
3.5-4 GHz range.
– Metropolitan area network (MAN) protocols, such as
WiMAX (Worldwide Interoperability for Microwave
Access) are based on standards such as IEEE 802.16,
designed to operate between 2 to 11 GHz.
– Mobile Broadband Wireless Access (MBWA) protocols
based on standards specifications such as IEEE 802.20
13
operate between 1.6 and 2.3 GHz.
 Microwave Applications
• Communication
– Mobile phone networks, like GSM, use the low-microwave/high-
UHF frequencies around 1.8 and 1.9 GHz in the Americas and
elsewhere, respectively.
– Most satellite communications systems operate in the C, X, Ka,
or Ku bands of the microwave spectrum.
– Satellite TV either operates in the C band for the traditional
large dish fixed satellite service or Ku band for direct-broadcast
satellite.
– Military communications run primarily over X or Ku-band links.
• Commercial Applications
– Commercial implementations are in the 2.3 GHz, 2.5 GHz,
3.5 GHz and 5.8 GHz ranges (ISM band- Industry, Science and
Medicine band).

14
 Microwave Applications
• Navigation
– Global Navigation Satellite Systems (GNSS) broadcast
navigational signals in various bands between about 1.2
GHz and 1.6 GHz.
– These include the Chinese Beidou, the American Global
Positioning System (GPS) and the Russian GLONASS.
• RADAR
– Radar uses microwave radiation to detect the range,
speed, and other characteristics of remote objects.
– Weather prediction
– Geological survey for natural resource exploration.
– Air traffic control, road traffic surveillance.

15
 Microwave Applications
• Radio astronomy
– Celestial body research.
– Distance measurement.
• Heating and Power Application
– A microwave oven uses microwave radiation at a
frequency near 2.45 GHz.
– Dielectric heating through energy absorption.
– Microwave heating is used in industrial processes for
drying and curing products.
• Security
– RFID based identification system.
– Motion detectors.

16
 Microwave Applications
• Medical Use
– Photoacoustic imaging (ultrasound).
– CT scan, X-rays, MRI like imaging.
– Thermo-therapy, LASER therapy.
– Cancer treatment.

17
Behavior of circuits at conventional
and RF/Microwave bands

“At high frequencies all

18
Behavior of circuits at conventional
and RF/Microwave bands
Resistor

19
20
21
Inductor

22
23
Capacitors

24
25
 Behavior of Circuits at Conventional
and RF/Microwave Bands
Low Frequency/ Conventional RF/Microwaves
• Bandwidths are limited • Provide large bandwidth so its
hence small no. of channels possible to adjust large no. of
can be adjusted. channels.
• It uses lumped element • It uses distributed circuit
circuit theory. theory (ohm/m, H/m, F/m).
• Scattering phenomena like
• Current flow and voltage absorption, reflection,
drops are used to calculate refraction, etc. are used in
power. power calculation.
• Open wire, twisted cables, • Optical fibers, waveguides,
co-axial cables are used as strip lines, micro-strip lines are
transmission lines. common transmission lines.

26
 Behavior of Circuits at Conventional
and RF/Microwave Bands
Low Frequency/ Conventional RF/Microwaves
• Lumped circuit elements • Cavity resonators or resonant
lines are used as oscillators,
are used such as resistors, resonators, etc.
filters, oscillators, etc. • Density modulation or velocity
• It uses current modulated modulation are used using
magnetrons, klystrons, TWTs,
mode. etc.
• Almost all the solid state • Vacuum tube like devices,
micro-miniaturised solid state
devices can be used. devices like Gunn diodes,
• It can handle low power. tunnel diodes, IMPITT,
TRAPPIT, etc. are used.
• It can handle higher power.

27
Thank You

28