From unimap, Malaysia; Louisiana State U; HK City U;

Eastern Washington U;
 Introduction
 Oscillator is an electronic circuit that generates a
periodic waveform on its output without an external
signal source. It is used to convert dc to ac.
 Oscillators are circuits that produce a continuous
signal of some type without the need of an input.
 These signals serve a variety of purposes.
 Communications systems, digital systems
(including computers), and test equipment make use
of oscillators
 Application of Oscillators
Oscillators are used to generate signals, e.g.
 Used as a local oscillator to transform the RF signals to IF
signals in a receiver;
 Used to generate RF carrier in a transmitter
 Used to generate clocks in digital systems;
 Used as sweep circuits in TV sets and CRO.

Ref:06103104HKN 3 EE3110 Oscillator

Oscillators
 Oscillators are circuits that generate periodic
signals
 An oscillator converts DC power from the power
supply into AC signal power spontaneously -
without the need for an AC input source

Figure 9.67 Repetitive ramp waveform.

 Types of oscillators
1. RC oscillators
 Wien Bridge
 Phase-Shift
2. LC oscillators
 Hartley
 Colpitts
 Crystal
3. Unijunction / relaxation oscillators
 Basic principles for oscillation
 An oscillator is an amplifier with positive feedback.
Ve Vo
Vs A
+
Vf
b
Ve  Vs  V f (1)
V f  βVo (2)
Vo  AVe  AVs  V f   AVs  βVo  (3)
 Basic principles for oscillation

Vo  AVe
 AVs  V f   AVs  βVo 
Vo  AVs  AbVo
1  Ab Vo  AVs
 The closed loop gain is:
Vo A
Af  
Vs 1  Aβ 
 Basic principles for oscillation
 In general A and b are functions of frequency and
thus may be written as;

As 
A f s   s  
Vo
Vs 1  As β s 
As βs  is known as loop gain
 Basic principles for oscillation
 Writing T s   As β s  the loop gain becomes;
As 
A f s  
1  T s 
 Replacing s with j

A jω
A f  jω 
1  T  jω
 and T  jω  A jωβ jω
Barkhausen Criterion – another way

Figure 9.69 Linear oscillator with external signal Xin injected.

Barkhausen Criterion
 Basic principles for oscillation
 The feedback oscillator is widely used for
generation of sine wave signals.
The positive (in phase) feedback arrangement
maintains the oscillations.
The feedback gain must be kept to unity to keep the
output from distorting.
 Design Criteria for Oscillators
1. The magnitude of the loop gain must be unity or
slightly larger
Aβ  1 – Barkhaussen criterion

2. Total phase shift, of the loop gain mus t be

Nx360° where N=0, 1, 2, …
 RC Oscillators
 RC feedback oscillators are generally limited to
frequencies of 1 MHz or less.

 The types of RC oscillators that we will discuss are

the Wien-bridge and the phase-shift
 Phase-Shift Oscillator
 The phase shift oscillator utilizes three RC circuits
to provide 180º phase shift that when coupled with
the 180º of the op-amp itself provides the necessary
feedback to sustain oscillations.
 The gain must be at least 29 to maintain the
oscillations.
 The frequency of resonance for the this type is
similar to any RC circuit oscillator:

1
fr 
2 6 RC
 Phase-Shift Oscillator

C R2
R
C v2
C v1 v2 v3
vi v1 vo

R R
vo R2
A( s)  
3
v3 R
 sRC   sRC 
v1   vi v3    vi
 1  sRC   1  sRC 
3
 sRC 
2
 sRC  v3
 b ( s)  
v2    vi 
 1  sRC  vi  1  sRC 
 Phase-Shift Oscillator
 Loop gain, T(s):
3
 R2  sRC 
T ( s )  A( s ) b ( s )    
 R  1  sRC 
 Set s=jw
3
 R2  jRC 
T ( j )    
 R  1  jRC 
 2
R ( j RC )( RC ) 2
T ( j )   
 
 R  1  3 R C  jRC 3   R C
2 2 2 2 2 2
 
 Phase-Shift Oscillator
 To satisfy condition T(jwo)=1, real component must
be zero since the numerator is purely imaginary.
1  3 R C  0
2 2 2

 the oscillation frequency: 1

0 
3RC
 Apply wo in equation:
 R2  ( j / 3 )(1 / 3)  R2  1 
T ( jo )       
 R  0  ( j / 3 )3  (1 / 3)  R  8 
To satisfy condition T(jwo)=1
R2 The gain greater than 8, the circuit will
8 spontaneously begin oscillating & sustain
R oscillations
 Phase-Shift Oscillator

1 R2
fo   29 The gain must be at least

2 6 RC
29 to maintain the
R oscillations
 LC Oscillators
 Use transistors and LC tuned circuits or crystals in
their feedback network.
 For hundreds of kHz to hundreds of MHz frequency
range.
 Examine Colpitts, Hartley and crystal oscillator.
 Colpitts Oscillator
 The Colpitts oscillator is a type
of oscillator that uses an LC
circuit in the feed-back loop.
 The feedback network is made
up of a pair of tapped
capacitors (C1 and C2) and an
inductor L to produce a
feedback necessary for
oscillations.
 The output voltage is
developed across C1.
 The feedback voltage is
developed across C2.
 Colpitts Oscillator
 KCL at the output node:
Vo Vo Vo
  g mVgs  0 - Eq (1)
1 R 1
sL 
sC1 sC 2
 voltage divider produces:
 1 
 
Vgs   sC2 
 Vo
 1 
 sC  sL  - Eq (2)
 2 
 substitute eq(2) into eq(1):
 

Vo  g m  sC2  1  s 2 LC2 
1
  sC1   0
 R 
 Colpitts Oscillator
 Assume that oscillation has started, then Vo≠0
 1
2
 sC1  C2    g m    0
s LC2
s LC1C2 
3

R  R
 Let s=jω
 1  2 LC2 
 g m    
  j C1  C2    2 LC1C2  0
 R R 
 both real & imaginary component must be zero
 Imaginary component: 1
o 
 C1C2  - Eq (3)
L 
 C1  C2 
 Colpitts Oscillator
 both real & imaginary component must be zero
 Imaginary component:
 2 LC2 1
 gm  - Eq (4)
R R
 Combining Eq(3) and Eq(4):
C2
 gm R
C1
 to initiate oscillations spontaneously:
 C2 
g m R   
 C1 
 Hartley Oscillator
 The Hartley oscillator is
almost identical to the
Colpitts oscillator.
 The primary difference
is that the feedback
network of the Hartley
oscillator uses tapped
inductors (L1 and L2) and
a single capacitor C.
 Hartley Oscillator
 the analysis of Hartley oscillator is identical to that
Colpitts oscillator.
 the frequency of oscillation:
1
o 
L1  L2 C
 Crystal Oscillator
 Most communications and digital applications require the
use of oscillators with extremely stable output. Crystal
oscillators are invented to overcome the output fluctuation
experienced by conventional oscillators.
 Crystals used in electronic applications consist of a quartz
wafer held between two metal plates and housed in a a
package as shown in Fig. 9 (a) and (b).
 Crystal Oscillator
 Piezoelectric Effect
 The quartz crystal is made of silicon oxide (SiO2) and
exhibits a property called the piezoelectric
 When a changing an alternating voltage is applied across
the crystal, it vibrates at the frequency of the applied
voltage. In the other word, the frequency of the applied ac
voltage is equal to the natural resonant frequency of the
crystal.
 The thinner the crystal, higher its frequency of vibration.
This phenomenon is called piezoelectric effect.
 Crystal Oscillator
 Characteristic of Quartz
Crystal
R
 The crystal can have two resonant
frequencies; CM
L
 One is the series resonance frequency f1
which occurs when XL = XC. At this C
frequency, crystal offers a very low
impedance to the external circuit where
Z = R.
 The other is the parallel resonance (or
antiresonance) frequency f2 which
occurs when reactance of the series leg
equals the reactance of CM. At this
frequency, crystal offers a very high
impedance to the external circuit
 Crystal Oscillator
 The crystal is connected as a series element in the
feedback path from collector to the base so that it is
excited in the series-resonance mode

BJT
FET
 Crystal Oscillator
 Since, in series resonance, crystal impedance is the smallest that
causes the crystal provides the largest positive feedback.
 Resistors R1, R2, and RE provide a voltage-divider stabilized dc bias
circuit. Capacitor CE provides ac bypass of the emitter resistor, RE
to avoid degeneration.
 The RFC coil provides dc collector load and also prevents any ac
signal from entering the dc supply.
 The coupling capacitor CC has negligible reactance at circuit
operating frequency but blocks any dc flow between collector and
base.
 The oscillation frequency equals the series-resonance frequency of
the crystal and is given by: 1
fo 
2 LCC