Chapter 5

Arrival Charts
 Chapter 5 Arrival Charts

§5.1 Introduction
§5.2 The Layout & Information of
STAR Charts
§5.3 Example
 §5.1 Introduction
Standard terminal arrival route (STAR)
procedures provide a method for leaving
the enroute structure and transitioning
into a busy or congested terminal area.
They typically terminate with an instrument
or visual approach procedures.
STAR propose:
STARs are designed to simplify arrival
procedures for pilots and air traffic
controllers by streamlining ATC
instructions for frequently used arrival
patterns.
For Example:
 STAR identifier

ARRIVAL identifier
§5.1.2 Locating Arrival Charts
Arrival charts are normally filed in the
Jeppesen Airway Manual before the
departure charts for the corresponding
airport.
A white-on-black box located on the upper
right corner of the chart identifies the
chart as a STAR.
How to find a arrival chart for a particular
airport:
• Look up the city in which the airport is
located.
• Look up the airport name.
• The index number at the top of the
chart ends in "0-2" for arrival charts.
When more than one arrival chart exists for
an airport, their index numbers are listed
in alphabetic sequence.
• One or several arrival procedures may
be displayed on one chart, with the
name of the arrival listed at the top of
the plan view section.
Some airports may use arrival procedures
for another airport in the area.
§ 5.2 The Layout & Information of STAR
Charts

• The Heading
• Plan View
• Heading Border
• Communications
• Transition Altitude/Level
• Restrictions
 §5.2.1.1 Heading Border
The heading border data located at the
top border of each Jeppesen arrival
chart, contains standard information to
help you quickly identify and retrieve the
proper arrival procedure.
Revised Dates Location Name
Primary Airport Name Effective Dates
Index Number
Chart Procedure
Identifier
 Chart procedure identifier
• STAR
Chart Procedure Identifier
• ARRIVAL

• LOST COMM STAR: A LOST COMM

provides arrival procedures that address
only lost communication procedures.
Location Name
Primary Airport Name
Chart Index Number
Dates
 §5.2.1.2 Communications
• D-ATIS: This symbol indicates that digital
ATIS (Automatic Terminal Informal
Service) is available for those aircraft that
have the equipment to receive it.

• *ATIS
§5.2.1.3 Transition Level and
Altitude
 §5.2.1.4 Chart Restrictions
In addition to the name of the arrival, the
chart title may include any number of
restrictions, such as:
• Type of aircraft
• Speed
• Onboard Equipment
• Ground-based Equipment
• Abatement Procedure
 Type of Aircraft

Some routes are designated specifically

for jet, turboprop, or non-turbojet
airplanes.
 Speed
Restrictions on speed are often noted in a
reverse type box with several criteria for
the pilot to follow.
 Onboard Equipment
Some arrivals are designed for aircraft with
specific equipment; for example, DME, GPS, or
RNAV. Equipment required may be specified in
the title, or in this case, special procedures
might be required if certain equipment is not
available.
 Ground-based Equipment
When an arrival is based on specific ground-
based equipment, it may include restrictions if
that equipment is not operative. For example, in
this chart, you only use this chart when the
Glasgow VOR is unserviceable. In this situation,
primary navigation is conducted using the
Glasgow NDB as an alternative navaid.
Abatement Procedure
 §5.2.2 Plan View

• Chart Naming and Numbering

• Orientation
• Airports
• Navaids and Fixes
• Flight Tracks
• Navigation Planning
 §5.2.2.1 Chart Naming and
Numbering
Generally, arrival procedures are named after
the first fix on the STAR .
Sometimes a plan view displays more than
one arrival procedures. When several
arrivals are named from the same fix , they
are distinguished numerically (if the
procedure name does not include a number)
or alphabetically (if the procedure name
does include a number).
Typically in the United States, transition routes
guide pilots from the enroute structure to a
specific fix in the STAR. In these cases, the
STAR name is usually the same as the last
fix on the enroute transitions where they
come together to begin the STAR.
A few arrival charts, such as the 10-2A chart
for Warsaw, are simply named “ARRIVAL
PROCEDURE,” followed by the designations
of applicable runways for the route charted.
These charts represent preferred arrival
routes approaching the airport.
With the arrival name, a number of other
important data may be listed:
• Computer code
• Arrival type
• Arrival direction
• Runway designation
 Computer Code
For airports that have computerized their route
identification for flight planning/filing purposes,
the computer code for a particular arrival
procedure is displayed in parentheses following
the route name. This is omitted when there are
no computerized routes for an airport.
 Arrival Type
The type of arrival is enclosed in parenthesis
following the name of the arrival. Arrival types
could be: PILOT NAV, RNAV, VECTOR, DME,
GPS, or LOST COMMS. For more information
about the different types of arrivals, see the
Flying an Arrival lesson later in this course.
 Arrival Direction
Many large airports have an arrival covering each
of primary directions that an aircraft might
approach an airport, such as “FROM EAST”
 Runway Designation
If an arrival applies to specific runways, these
will be listed just below the title. Otherwise ,
they are specified in the plan view of the chart.
§5.2.2.2 Orientation

North arrow

Not To Scale
Arrival charts may include any of the
following types of boundaries:
• Region borders between countries or
states
• Transition level boundaries
• Special use airspace boundaries
Region Borders
Transition level boundaries
 Special Use Airspace
Boundaries
When special use areas (SUAs) are referenced in
the arrival procedure, they are charted on the
plan view. In addition to the outlined depiction for
the area, the following information may be
included:
• Identifier: The Identifier includes three items of
information: the country code (on U.S. charts the
country designation is omitted), the type of
SUA — (P)rohibited, (D)anger, or (R)estricted —
and a sequential number.
• Lower and upper limits
• Time of operation

When times of operation and limits are

omitted, refer to the corresponding enroute
chart for additional information.
 §5.2.2.3 Airports
Most arrival charts are designed for one
airport , referred to as the primary
airport. The primary airport is displayed
in the plan view by as a shaded circular
area, centered on an outlined sketch of
all active or temporarily closed runways.
When the procedure also serves other
airports, a notation is included in the plan
view lists the additional airports served.
Also, the elevations and runway information
are listed nearby the airports.
 §5.2.2.4 Navaids and Fixes
Arrival routes are defined by various navigation
facilities in the area. Typically, the arrival chart
shows all the navaids that define the route
within the plan view section of the chart.
Also, along the route, there may be designated
locations that provides a means for checking
the progress of your flight .Again ,these fixes
may be defined by their relative position to
various navaids, as well as latitude and
longitude positioning.
 Navaid

On the STAR chart, the navaid has not

the symbol of the magnetic north!
Occasionally, a chart references a navaid that
is not located on the chart . In lieu of the
navaid symbol , the plan view provides the
navaid identifier, frequency, and Morse code.
 §5.2.2.5 Flight Tracks
• Arrival Tracks
• Transition Routes
• Radar Vectors
• Holding Patterns
• Visual Flight Tracks
 Arrivals Tracks
An arrival track is depicted as bold, solid line with
a prominent arrowhead at the end of the route
segment. These tracks are typically annotated
with the following information:
• The magnetic course given as bearing from, or
to, a specific navaid. On some routes, you fly a
heading rather than receive positive course. In
this case, the letter “hdg” are printed with the
magnetic bearing.
• The distance in nautical miles. Occasionally,
the distance will also be given in DME. In
such cases, the number is preceded by the
letter D.
• The expected altitude at which you will fly
the segment. Altitudes are established above
mean sea level in feet, or , when the altitude
is preceded by the letters FL, as flight level.
Altitudes may be given as either MEAs,
MOCAs, or MAAs.
 MEA
The MEA is the minimum enroute altitude that
guarantees navigation radio reception for the
stations that define the route and least 1,000
feet obstacle clearance in non-mountainous
terrain areas. For areas with mountainous
terrain, the MEA guarantees 2,000 feet
obstacle clearance. The MEA is the most
common altitude shown on arrival charts. For
example, the MEA between the JASON and
GILBY intersections on Washington’s Jasen
Three arrival is 5,000 feet.
 MOCA
The MOCA is the Minimum Obstruction
Clearance Altitude. When this altitude is
maintained, you are guaranteed
obstacle clearance, but navigation radio
reception is only assured within 22
nautical miles of the station. MOCA
altitudes are shown in the same manner
as MEA altitudes, except that the letter
“T” follows the altitude limit.
 MAA
A maximum authorized altitude (MAA) is a
ublished altitude representing the
maximum usable altitude or flight level for
an airspace structure or route segment.
It is the highest altitude on a Federal
airway, jet route, RNAV low or high route,
or other direct route for which an MEA is
designated at which adequate reception
of navigation signals is assured.
Holding Patterns

Outbound Bearing

Holding Fix

Inbound Bearing

Hold altitude:
• MHA: minimum
holding altitude
• MAX: maximum
holding altitude
Leg limit :When DME
figures are associated
with a holding course
symbol, the first denotes
the location of the
holding fix. The second
figure is the outbound
limit.
 Time limit

Holding speed
limit
 §5.2.2.6 Navigation Planning
• Routing information
• Descent planning
• Lost communications procedures
• Speed limit procedures
 Routing Information
Textual descriptions, when provided, give written
details of each arrival route and transition. The
text is separated and labeled in a manner that
helps you clearly distinguish each flight track
in the procedure.
Descent Planning
 Lost Communications
Procedures
When communication with ATC are lost
while on an IFR flight, you are expected
to follow standard lost communications
procedures unless you have been
advised to expected a specific
clearance, or when other instructions
are published in a lost communications
procedures.
For many arrivals, lost communications
procedures are published in the plan view
section of arrival chart, within a cross-
hatched or “LOST COMMS” border.
In some airport, lost communications
procedures are published in the plan
view section of arrival chart, within
“ ” border.
If there is a individual published lost
communication procedure for a specific
airport, the STAR is displayed
individually . Meanwhile, “LOST
COMMUNICATION” is labeled nearby
the type of arrival procedures.
 Altitude & Speed Limits
Arrival charts often include speed limit
restrictions or procedures for all or parts
of the arrival procedure. when the
speed limits apply to the entire
procedure, the limit is typically part of
procedure title, as shown here. In this
case, no matter where on the procedure
you are, if you are below 10,000feet,you
have a max IAS of 250 knots.
FRANKFURT/MAIN Airport
In other cases, speed limits may simply
be annotated to the portion of procedure
to which they apply.
Finally, some speed limits are included as
a boxed procedure.
 §5.3 Example
• Flight Planning for Arrivals
• Flying a Standard Arrival
• Flying an RNAV Arrival
• Flying with Lost Communications
• Flying a Visual Arrival
When flying a visual arrival, you want to
note the minimum safe altitude (MSA).