PCB Design Presentation: Jakia Afruz

PCB Design Presentation
Jakia Afruz
 Printed Circuit Board
 Electronic Board that connects circuit
components
 PCB populated with electronic components
is a printed circuit assembly (PCA)
 PCBs are rugged, inexpensive, and can be
highly reliable
 Mass manufacturing
 Professional
 Conducting layers are typically made of
thin copper foil.
 The board is typically coated with a solder
mask that is green in color. Other colors
that are normally available are blue and
red.
 Unwanted copper is removed from the
substrate after etching leaving only the
desired copper traces or pathways
 Components
 Pads
 Traces
 Vias
 Top Metal Layer
 Bottom Metal Layer
 Components are the actual devices
used in the circuit.
 This includes input/output connections.
 I/O ports, including power supply
connections, are also important in the
PCB design.
 Location that components connect to.
 You will solder components to the pads
on the PCB.
 Pads will connect to traces.
 Pads have an inner diameter and outer
diameter.
 Traces connect pads together.
 Traces are essentially the wiring of the
PCB.
 Equivalent to wire for conducting signals
 Traces sometimes connect to vias.
 High current traces should be wide.
 Signal traces usually narrower than
power or ground traces
 Pad with a plated hole connecting
traces from one layer of board to other
layers.
 Attempt to minimize via use in your
PCBs.
 Some component leads can be used as
vias.
 Most of the components
reside on the top layer
 Fewer traces on the top
layer
 Components are soldered
to the pads on the top
layer of PCB
 Higher circuit densities
 Few components on this layer.
 Many traces on this layer.
 Most soldering done on this layer.
 Often, many signal wires need to exist in
too small of a space and must overlap.
 Running traces on different PCB layers is
an option.
 Multilayer PCBs are often expensive.
 Solution: use jumpers
 Protect copper traces on outer layers from
corrosion
 Areas that shouldn't be soldered may be
covered with polymer resist solder mask
coating
 Designed to keep solder only in certain
areas
 Prevents solder form binding between
conductors and thereby creating short
circuits
 Printing on the solder mask to designate
component locations
 Readable information about component
part numbers and placement.
 Helpful in assembling, testing and
servicing the circuit board.
 More then a top and bottom layer.
 Typically there will be a power plane,
ground plane, top layer, and bottom
layer.
 Sometimes signal layers are added as
needed.
 Sometimes RF planes made of more
expensive materials are added.
 Component Size
 Heat Dissipation
 Input and Output
 Mounting Points
 Make sure components will actually fit.
 This especially applies for circuits that
require high component densities.
 Some components come in multiple
sizes. SMT vs Through Hole
 Sometimes you can get tall and narrow
caps or short and wide capacitors.
 Heat sink dissipates heat off the
component
 Doesn’t remove the heat just moves it
 Some components may get hot. Make
sure you get a large enough heat sink.
 Data sheets specify the size of the heat
sink
 A short circuit may result when two
devices share the same heat sink
 The PCB needs to be mechanically
secured to something.
 Could be the chassis-consist of metal
frame on which the circuit boards and
other electronic components are
mounted.
 Could be another PCB/socket on PCB.
 Could be attachments to a heatsink.
 High frequency circuits
 Series Inductance
 Shunt Capacitance
 Inductive Coupling
 Capacitive Coupling
 Not an issue for low frequency circuits(<10
Mhz)
 The inductance of a trace may be
signifigant.
 For power connections, a shunt capacitor
is added to counter the series inductance
of a long trace.
 A capacitor has a low AC impedance
source
 A 100nF capacitor is often used along with
a larger capacitor. 100 nF ceramics have
very low impedance at higher frequencies.
 Result of wide wires over a ground plane.
 Limits speed of circuits, including digital
circuits
 Typically insignificant for low
performance circuits.
 To minimize place a capacitor from
voltage to ground
 Transfer of energy from one circuit
component to another through shared
magnetic field
 Change in current flow through one
device induces current flow in other
device
 Current flow in one trace induces current
in another trace
 Minimize the long parallel runs of traces
 Run traces perpendicular to each other
 Transfer of energy in electrical n/w due
to capacitance between circuit nodes
 Minimizing long traces on adjacent
layers will reduce capacitive coupling
 Ground planes are run between the
signals that might affect each other.
 Thoroughly simulate your circuit-make sure
the circuit worked in simulations
 Thoroughly test the prototype-make sure
the circuit worked on the bread board
 Have all the data sheets handy for every
components
 Play around with the placement of the
components
 Important to simulate the circuits before
building them
 Allow margin for component tolerances
 Avoid using precise components. e.g a
PWM controller that requires exact 10 V
DC to work and will fail if there is 10.01V
 High performance circuits or SMT devices
require PCBs and should be simulated
extensively first.
1. Film Generation 2. Shear Raw Material
Industry standard
3. Drill Holes 0.059" thick, copper
clad, two sides
4. Electrolus copper 5. Apply Image
Apply copper in hole barrels Apply Photosensitive Material to

develop selected areas from
panel
6. Strip and Etch 7. Solder Mask
•Remove dryfilm, then Apply solder mask area to

etch exposed copper entire board with the exception
•Tin protects the copper of solder pads
circuitry from being
etched
8. Solder Coat 9. Silkscreen
Apply solder to pads Apply white letter marking

using screen printing
process
http://www.youtube.com/watch?v=Q6WJqjVleG
0&feature=related
http://www.advancedcircuits.com/
 PCB Design slides by Chris Stahl
 www.wikipedia.org
 www.pcbexpress.com
 A Practical Guide to high-speed printed
circuit board layout
 http://www.advancedcircuits.com
 How to download the software (EAGLE Layout
editor)
1. Go to http://www.cadsoftusa.com
2. Click ‘Freeware’
3. Click ‘Download’
4. Find the correct version (Windows/Linux,English)
5. Also download Manual and Tutorial
 http://www.pcbexpress.com
 http://www.freepcb.com
 http://www.4pcb.com
 http://www.pentalogix.com

PCB Design Presentation: Jakia Afruz

Uploaded by

Copyright:

Available Formats

PCB Design Presentation: Jakia Afruz

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

PCB Design Presentation: Jakia Afruz

Uploaded by

Copyright:

Available Formats

PCB Design Presentation

Apply copper in hole barrels Apply Photosensitive Material to

•Remove dryfilm, then Apply solder mask area to

Apply solder to pads Apply white letter marking

You might also like