"Speed Control and Protection of Induction Motor Using Internet of Thing

Project Introductive Seminar
on
“Speed Control and Protection of
Induction Motor Using Internet of
Thing.
Presented by
Pratik Suryawanshi Darshan Randive
Gaurav Meshram Hashal Dhawle
Prakash Bhagat
Under the guidance of
Dr. Rakesh G. Shriwastava
Associate Professor
Department of Electrical Engineering
JAIDEV EDUCATION SOCIETY’S

J D COLLEGE OF ENGINEERING AND MANAGEMENT, NAGPUR
Department of Electrical Engineering
“Igniting minds to illuminate the world”
2018-19
CONTENTS
 Objective
 Introduction
 Literature Review
 Block Diagram
 Simulation architecture
 Simulation Result Analysis
 Hardware Implementation
 Hardware Result Analysis
 Estimation Of Components
 Advantages
 Conclusion
 Future Scope
 References
OBJECTIVE
 Controlling speed of single phase induction motor by using

microcontroller AT89S52.
 Get information about running status of motor on PC by
using IOT technology.
 To protect motor from overloading.
INTRODUCTION
 Our project comes under the category of IOT, which is
configurable using Cloud platform to control ESP8266 Wifi
Module. We wanted to be able to control our projects WiFi
network, We can control the speed of the Induction motor
using Cloud base web page.
 We have made the speed control button on cloud. Using this button
we can sent a data to define ESP8266 Module, After receiving
data is send to the Microcontroller and suitable action is take like
turn on the motor in defined speed etc . We have control the speed
of induction motor using the charge control circuit.
 Signal from Microcontroller drive relays and relays are connected
to electrical load & real time data is displayed to LCD interfaced.
 Microcontroller is not able to drive the relay so that we have used the
relay driver IC ULN2003.
 We have also used the LCD to display the status of the Device.
LITERATURE REVIEW
[1] In 2003, a paper on , “IOT Based Speed Control of Single Phase
Induction Motor”.
The main objective of this paper is to control the speed of
single phase introduction motor using IOT technology. Internet is the
most widely used high speed and easily accessible communication
medium in the modern day world.
[2] In 2017, a paper on , “Speed Monitoring And Controlling of
Motor Using Internet of Things (IOT) Enhanced With WI-FI”.
The rapid growth of industry and advancement of
technology has resulted in reduction of human effort, the main
reason for which being machines are playing an important role in
our life. In this project, we use internet to establish communication
between the user and monitoring unit. In this proposed system, we
are monitoring and controlling the speed of DC motor as well as
direction of the motor. This system consist of microcontroller.
[3] In 2017, a paper on , “IOT Based Wireless Induction Motor
Monitoring”.
In this study, a factory induction motor was monitored
with wireless TCP/IP protocol in order to detect and predict
deviation from normal operating parameters before the occurrence of
motor failure. In this way, the production process is not impeded and
the required maintenance or replacement can be performed with the
least possible disruption.
[4] In 2017, a paper on , “Induction Motor Fault Detection,
Protection and Speed Control Using Arduino”
The most extensively used motor in the industry is the
induction motor. The fault in the induction motor may lead to
breakdown of the induction motor and an increase in expense to the
industry. So in this paper we have discussed a system which is cheap
as compared to the other system and also cost effective. This system
monitors parameter such as speed, temperature, current and voltage
using an Arduino microcontroller.
BLOCK DIAGRAM
TRANSMITTING SECTION
POWER LCD DISPLAY

SUPPLY
MICRO-
CONTROLLER
ESP8266 ULN2003
WIFI
MODULE
(IoT)
Relay1 Relay2 Relay2

CLOUD OVER THE
NETWORK
CC
CONTROLLING SECTION CC3 CC
1
2
COMPUTER
CONTROLLING
PARAMETER FROM WEG
PAGE USING CLOUD Fig a. Block diagram of Home
Appliences by IOT
1. POWER SUPPLY
 The 230V AC supply is first stepped down to 12V AC using a step down
transformer.
 This is then converted to DC using bridge rectifier.
 The AC ripples is filtered out by using a capacitor and given to the input
pin of voltage regulator 7805.
 At output pin of this regulator we get a constant 5V DC which is used for
MC and other ICs in this project.
2. MICROCONTROLLER
 We have used the Microcontroller of 80C51 family i,e AT89S52
manufactured by ATMEL.
 It is a smaller Computer.
 Has on-chip RAM, ROM, TIMER, COUNTER, I/O ports...
CPU RAM ROM

A single chip
Serial
I/O Timer COM Microcontroller
Port Port
BLOCK DIAGRAM OF MC
External interrupts
On-chip Timer/Counter
ROM for
Interrup program On-chip Timer 1 Counter
t Control code RAM Inputs
Timer 0
CPU
Bus Serial
4 I/O Ports Port
OSC Control
P0 P1 P2 P3 TxD RxD
Address/Data
FEATURES OF MC
 8K Bytes of In-System Programmable (ISP) Flash
Memory
 4.0V to 5.5V Operating Range
 Fully Static Operation: 0 Hz to 33 MHz
 256 x 8-bit Internal RAM
 32 Programmable I/O Lines
 Three 16-bit Timer/Counters
 Eight Interrupt Sources
 Full Duplex UART Serial Channel
PIN DESCRIPTION
POWER ON RESET CIRCUIT
+5V
+
10 uF
31
EA/VPP
X1
30 pF 19
11.0592 MHz
8.2 K
X2
18
30 pF
9 RST
3. NODE MCU ESP 8266 (WIFI MODULE)
NODEMCU ESP8266 is very highly integrated System on Chip (SoC)

that includes an Xtensa LX106 core processor, RAM, and RF front-
end allowing a Wi-Fi TCP/IP stack to be implemented on board with
just a few components.
NODE MCU ESP 8266 (WIFI MODULE)
Features of ESP 8266
 It provides capabilities for 2.4 GHz Wi-Fi (802.11 b/g/n,
supporting WPA/WPA2), general-purpose input/output (16 GPIO),
 Inter-Integrated Circuit (I²C).
 analog-to-digital conversion (10-bit ADC).
 Serial Peripheral Interface (SPI),
 UART (on dedicated pins, plus a transmit-only UART can be

enabled on GPIO2)
 pulse-width modulation (PWM).

4. RELAY
 A relay is an electrically operated switch.
 Current flowing through the coil of the relay creates a magnetic field which
attracts a lever and changes the switch contacts.
 The coil current can be on or off so relays have two switch positions and
have double throw (changeover) switch contacts as shown in the diagram.
CONTD..
 Relays allow one circuit to switch a second circuit which can be completely
separate from the first.
 For example a 12 voltage battery circuit can use a relay to switch a 230V
AC mains circuit.
 There is no electrical connection inside the relay between the two circuits,
the link is magnetic and mechanical.
 To drive relay we used ULN2003 relay driver IC.

RELAY DRIVER IC ULN2003
 ULN is Relay driver application

 The ULN2003 is a monolithic high voltage and high
current Darlington transistor arrays.
 It consists of seven NPN Darlington pairs that features
high-voltage outputs with common-cathode clamp diode for
switching inductive loads.
 The collector-current rating of a single Darlington pair is
500mA.
 The Darlington pairs may be paralleled for higher current
capability.
CONTD..
 The ULN functions as an

inverter.
 If the logic at input 1B is high
then the output at its
corresponding pin 1C will be
low.
5. LIQUID CRYSTAL DISPLAY (LCD)
 Most common LCDs connected to the microcontrollers are 16x2 and

20x2 displays.
 This means 16 characters per line by 2 lines and 20 characters per
line by 2 lines, respectively.
 The standard is referred to as HD44780U, which refers to the
controller chip which receives data from an external source (and
communicates directly with the LCD.
CONTD..
 If an 8-bit data bus is used the LCD will require 11 data lines(3 control
lines plus the 8 lines for the data bus)
 The three control lines are referred to as EN, RS, and RW
 EN=Enable (used to tell the LCD that you are sending it data)
 RS=Register Select. When RS=0; data is treated as a command & When
RS=1; data being sent is text data.
 R/W=Read/Write . When RW=0; the data written to the LCD & When
RW=0; the data reading to the LCD.
SIMULATION ARCHITECTURE
HARDWARE IMPLIMENTATION
 PCB Designing- Printing, ironing, etching, drilling & soldering
 Component mounting on PCB
 Complete hardware
SOFTWARE REQUIREMENTS
o Keil an ARM Company makes C compilers, macro assemblers,

real-time kernels, debuggers, simulators, integrated
environments, evaluation boards.
o Arduino 8.1 Programer .

REFERENCE
o “The 8051 Microcontroller and Embedded systems” by
Muhammad Ali Mazidi and Janice Gillispie Mazidi , Pearson
Education.
o https://dashboard.arest.io/
o https://openhomeautomation.net/control-relay-anywhere-
esp8266/
o International journal of research in advent technology
(E- 2331-9637)
o www.arduino.com
o www.wikipedia.org
PCB AFTER ETCHING , DRILLING &
SOLDERING
SIMULATION RESULT ANALYSIS

"Speed Control and Protection of Induction Motor Using Internet of Thing

Uploaded by

Copyright:

Available Formats

"Speed Control and Protection of Induction Motor Using Internet of Thing

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

"Speed Control and Protection of Induction Motor Using Internet of Thing

Uploaded by

Copyright:

Available Formats

Project Introductive Seminar

JAIDEV EDUCATION SOCIETY’S

 Controlling speed of single phase induction motor by using

POWER LCD DISPLAY

Relay1 Relay2 Relay2

CPU RAM ROM

NODEMCU ESP8266 is very highly integrated System on Chip (SoC)

 analog-to-digital conversion (10-bit ADC).

 Serial Peripheral Interface (SPI),

 UART (on dedicated pins, plus a transmit-only UART can be

 pulse-width modulation (PWM).

 To drive relay we used ULN2003 relay driver IC.

 ULN is Relay driver application

 The ULN functions as an

 Most common LCDs connected to the microcontrollers are 16x2 and

 PCB Designing- Printing, ironing, etching, drilling & soldering

 Component mounting on PCB

o Keil an ARM Company makes C compilers, macro assemblers,

o Arduino 8.1 Programer .

o International journal of research in advent technology

You might also like