(S5) Qa340

QA340 (S5)
Hopper & Feeder
Feeder and
Hopper
Sandvik Mining and Construction

Feed Hopper
 Heavy duty hydraulically

operated Hopper
 Enables quick set-up time
 Hopper Capacity 6.95m³
 Vibrating 2 deck grid
*optional*

Feed Hopper
 Free swinging fingers

 Build in three identical section
 The aperture between the fingers
is 160mm Standard
 Aperture options
110,130,140,170,180,240,280mm
 The grid area is 7m² (2.2 x 3.2m)
 With the side doors raised the
total area is 9.24m² (2.2 x 4.2m)

Tipping Grid
 Radio control for raising
and lowering the tipping
grid
 A timer is also available for
raising and lowering the grid
 Tip angle of 96° on a
standard grid
 Tip Angle of 34° on a
vibrating grid

Feed Hopper
 Recessed hopper design

 This prevents large
material damaging the
side of the hopper when
falling to the ground
 Large access door for
maintenance of the feed
conveyor

Hopper Jacking Legs
 The hopper sits on 4

hydraulically operated
jacking legs
 These jacking legs have a
large surface area on each
foot, this helps with
 Loading with
dense/heavy material
 Setting up on soft
ground
 Made from 10mm thick
steel plate

Feeder Cassette
 Driven from flange

mounted hydraulic motor &
gear box assembly
 Heavy duty bed rollers
Which prolongs the life of
the belt
 1200mm belt width
 large hopper discharge
plates, which prevents
spillage when running high
capacities

Main Conveyor
 Rubber curtain to stop

material bouncing back
down the belt
 High rise walls stop
spillage when running
high capacity's
 Wing rollers along the
length for tracking the
belt

Main Conveyor
 The main conveyor

raises up away from
the screen box for
maintenance
 This enables quick &
easy screen mesh
change

Screen

Screen Box
 2 bearing screen box

 Double deck screen box
 Made from 11mm plate bolted
together
 Deck size on the first screen 2439 x
1524mm
 Deck size on the second screen
2439 x 1524mm
 Heavy duty screen box with
uniquely high throw and speed
 1200rpm shaft speed,
 7mm throw

Double Screen Design
First screen box is used as
a fines extractor
Second Box operates as

a grader.
Clean Gradings at very

34° 25° high output are
produced as material is
The majority of the undersize is exposed to a very
removed during initial impact large screening area
Screen Mesh
Piano wire/Harp
Square Mesh Elongated
Polyurethane
S-Harp/Diamond Punch Plate
Rubber
Drive
 The screens is driven

directly by heavy duty
flange mounted
hydraulic motors
 With spiral wrap
protected hoses

Screen Supports
 The Screen box is

mounted independently
from the chassis
 On a set of springs
 These absorb the
screens vibrations and
stops any strain
travelling thought the
main chassis.

Mesh Tensioning System
 The top and bottom

screen decks have a
quick tensioning
ratchet system.
 For quick screen mesh
tension and removal

Maintenance Platforms
 Hydraulically folding
maintenance platform
either side of the
screen box
 None slip perforated
walkway

Chute
 Over size discharge chute

 This has a rubber drape
hanging over it, this is
attached to the screen so as
the screen vibrates so does
the drape
 This prevents any material
build up on sticky applications
 Rubber protection on the
hopper sides

Plant Conveyors
Fines
Conveyors Conveyor

Fines Conveyor
 Heavy duty belt

 1200mm wide
 Discharge height of
4565mm
 Hydraulically folding for
transport

Other Grading Size Conveyors
 Heavy duty chevron belt

 700mm wide
 Discharge height of 4620mm
 Hydraulically folding for
transport
 Each side conveyor had a
variable speed control from
0-120m/min

Side Conveyor
 The whole length of the side

conveyors we use steel
hydraulic pipes
 These acts as a heat
dissipater
 None flexing
 High anti spillage boards,
which are excellent on large
stone applications

Power Pack/Controls

Manual Control levers
 Simple user friendly manual

control levers for setup and
operation
 Each function is clearly
marked for ease of use
 The manual levers shown,
start and stop all the
conveyors and screen box
 Easy access to all
consumables in one location
 Fault finding hydraulic test
point all in one location

System Display
 Engine fault monitoring

of
 Coolant
Temperature
 Coolant level
 Engine Run
 Battery Voltage
 Oil Pressure
 Emergency Stop
 Radio Stop
 Water and Fuel
Sensor

Engine
 The QA340 (S5) is powered by a Duetz

2012 engine developing 100HP (75
KW) @ 2200 rpm.
 The engine compiles with all current
emission laws
 Average fuel consumption
approximately 10-14L/H
 Easy access for maintenance via three
canopy doors

Hydraulic Tank
 370 litre hydraulic tank

 Multi stage filtration system
to ensure all debris is
removed on every cycle
 Filters located at the top of
the unit for easy of
maintenance
 Level gauge with in build
temperature gauge

Hydraulic Components
 Simple On/Off type hydraulic

control blocks
 Easy access for maintenance
 Direct driven high power

and torque hydraulic
pumps
 Powering the Screen &
Track Drives

Maintenance
 Easy engine maintenance access

doors
 Access to
 Hydraulic filter
 Hydraulic tank top up
 Coolant level
 Engine oil

Fuel Tank
 290 litre Diesel Tank

 Optical diesel level gauge
 Heavy duty industrial size lockable
filler cap

Chassis
 Heavy duty “I” beam designed chassis

 With finite element analysis design

Tracks
Tracks

Tracks
 Hydraulically driven crawler track mounted for full site mobility.
 The full power of the engine is available for driving the tracks when needed.
 Length of 3310mm.
 Track Shoe Width 500mm.
 Motor drive 63cc
 Gear box ratio 122:1

Tracking
 Tracking is possible by either

 Wireless Radio Umbilical Controller
Controller
 Wired Umbilical
 Each track can be operated
independently for full site
flexibility .
Radio Controller

Daily Checks
 Check engine oil level,

 Refill as required
 Check coolant level

Weekly Checks

250 Hour Service
Machine Maintenance - Every 250 Hrs

Every 250 hours, the following maintenance must be carried out to ensure the best
performance and least possible breakdowns from your machine.
 1. Follow maintenance instructions laid out in engine manufacturers handbook.
 2. Inspect condition of conveyor belt and tracking.
 3. Inspect and adjust belt scrapers.
 4. Inspect and adjust wear rubbers.
 5. Inspect condition and tension of screen mesh.
 6. Inspect condition of all belt drums.
 7. Check for hydraulic leaks on pipes.

500 Hour Service
Every 500 hours, the following maintenance must be carried out:
 1. Follow maintenance instructions laid out in engine manufacturers
handbook.
 2. Carry out 250 hour maintenance schedule.
 3. Replace hydraulic air tank breather. (HF4003)
 4. Replace hydraulic return filter. (HF1004)
 5. Check hopper conveyor gearbox oil VG150 .
3 4 5

1000 Hour Service
 Machine Maintenance - Every 1000 Hrs

 Every 1000 hours, the following maintenance must be carried out:
 1. Follow maintenance instructions laid out in engine manufacturers
handbook.
 2. Carry out 250 hour maintenance schedule.
 3. Replace twist on hydraulic air tank breather. (HF4003)
 4. Change oil in the tracks.

2000 Hours
 Replace the hydraulic oil

 Replace the suction filters

Transport Dimensions
15,860 [52 ]
1/3”]
2,840 [9
3750 [12
1/3”]
Standard machine Total
weight 27,000Kg
Working Dimensions

Working Dimensions

Sound levels
80 dB 88 dB 86 dB 7M
81 dB 92 dB 88 dB 1M
85 dB
85 dB
82 dB
82 dB
82 dB 92 dB 87 dB
80 dB 87dB 88 dB

Options

Water Pump
 Hydraulically powered
water pump for use with
the dust suppression
systems
 No need for extra
hydraulic pumps as it uses
the existing hydraulic
circuit
 Takes water direct from a
water tank.
 Saves the need for a
pressurised water supply

Diesel Tank Pump
 Electrical re-fuelling
pump
 24 volt motor
 Powered from the
existing electrical
system
 Push button controlled

Bogie Unit Option

Magnet
 The magnet is designed to

separate the steel from the
feed material and then
discharge it away from the
machine.
 Variable Speed Belt.
 The Magnet can be lowered
or raised to suit the
application.

Hydraulic Shredder
 Optional Hydraulic
Shredder option
 Hydraulically raised &
lowered
 Double Shaft
 Fixed blade
 Shaft speed 650rpm

Summary
 Available Options
 Double Deck Vibrating grid
 Standard features
 Side Conveyor Feed boot Hardox lined
 Main conveyor  Hardox spreader plate
 Double deck screen box  Hopper Lined Hardox Plates
 Screen Tensioning system  Dust suppression including Canvas covers
 Hydraulic folding walkways  Working lights
 Top deck rubber screening mat
 Deutz Engine
 Remote diesel pump
 Remote Tracks
 Overband magnet & frame
 Water pump
 Double shaft shredder unit
 Arctic package -20°C
 Arctic package -30°C
 Tropical Package
 Central Lube system

Hydraulic System
Tail Conveyor
Mid-Size Conveyor
Fines Conveyors
Screen
Feed Conveyor
Power Pack R/H
Power Pack L/H
Tracks

Hydraulic System
CETOP
6 Station Manifold
D6 Valves
Main Drive Pump
PTO Pumps
6 Lever Spool Valve

Hydraulic System
Pump Location
1. The first pump
sends oil flow to the
D6 valve on to the
6 station manifold
and then supplies
the main conveyor
2. The second pump
1
Sends oil to the D6
valve onto the 6
station manifold
and then supplies
oil to the tail
conveyor and the
stockpiling
2
conveyors
3. Both pumps also Tandum Pump
supply the tracks Machine Displacement RPM Flow
QA450
via the D6 valves 32.3cc/32.3cc 69.5 L/M
QA440
QA340 2150
QA240 28.5cc/28.5cc 61.3 L/M
QA140

Hydraulic
PTO Pump Location

1. There are two sets
of pumps, one set
on the top PTO
Pump
2. The PTO is being 2
driven at a 1 : 1.189
Ratio
3. Pump 1 is
supplying oil to the
Vibrating Grid
option if fitted
4. Pump 2 is
supplying oil to all
of the set up levers Pump
around the machine 1
and to the over size
conveyor of on the
QA450 Pump 1 Pump 2
Pump Speed 2556 RPM Pump Speed 2556 RPM
Displacment 18cc Displacment 16.8cc
Max Flow 46 L/M Max Flow 43 L/M

Hydraulic
PTO Pump Location

1. PTO 2 is being
driven at a 1 : 1.023
Ratio
2. Pump1 is supplying
oil to the screen
box motors
3. Pump 2 is
supplying oil to the Pump
feed hopper
1 Pump
2
Tandum Pump
Machine Displacement RPM Flow
QA450 28.5cc/23.5cc 62.7L/M / 51.7L/M
QA440 23.5cc/23.5cc 51.7L/M / 51.7L/M
QA340 2200
QA240 25.4cc/17cc 55.9 L/M / 37.4 L/M
QA140

Hydraulic Drain Link to Pilot Pressure
other D-6 Valve from “C-Top”
D6 Valves
1. There are two D6
valves located in
the power pack
receiving oil from Flow from
the main drive Pump
pumps Flow to
function
2. The oil normally
travels through the
valve and on to the
Main Conveyor and
Tail Conveyor drive
3. When operated via Track Ports
the Ce-Top the oil is
diverted to the R/H
& L/H tracks
250 Bar
Tank
Return
Hydraulic
Pressure in and
Tracks Brake out ports
1. The tracks receive Release
oil from the D6-
Valve which is
piloted from the Ce-
top valve
Case Drain
Motion control
Tandum Pump Valves
Machine Displacement RPM Ratio
QA450
90cc 359 rpm 111. : 1
QA440
QA340 122. : 1
QA240 63cc 452 rpm
83.9 : 1
QA140
X-line
Hydraulic Checks
Tracks
1. We send pressure
down the brake line
to release the
tracks
2. The flow used to
drive the tracks
sends a pilot signal
down the X-line
check to allow the
return oil to flow
back to tank.
Brake release Pressure = Pressure

reducing @ 35 bar (508PSI)
= Return Flow
= Case Drain
= Brake Pressure
Hydraulic
Feed Hopper
1. The oil for the Feed
conveyor is being
supplied via the 6
Station manifold
which houses a
speed control for
varying the speed
from 0 – 16 m /min
Feeder Motor
Displacement 160cc
Gear Ratio 20:1
Max Speed 10-16 M/Min

Hydraulic
Control
6 Station Manifold valve
1. When the pressure
in the fines collector Test
circuit reaches Point
170bar (2465Psi) it
causes the pilot
pressure valve to Speed control
shuttle across and valve
causes the feed
conveyor to stop
Pilot pressure
2. When the pressure Relief valve
drops down to Valve
160bar (2320Psi) in
the fines circuit it
will allow the feeder
to start the feed
conveyor

Hydraulic
Screen Motor
1. The web-tec speed
control is locked to
give the screen box
a speed of a 1000
rpm
2. Note: do not
increase this speed
Screen Box
Displacement 82.6cc (5.04C/In)
RPM 1000 (Restricted)
Running Pressure Empty 60-70 Bar (870-1015 Psi)
Throw 9mm
Hydraulic System
Screen Box
1. These manual
control levers are
used to set the
machine up, for
maintenance and
for fine tuning your
application
Select lever
to view
function

Hydraulic
Screen
1. “SCREEN BOX
UP/DOWN” this is
used for fine tuning
your application
2. “MESH CHANGE
UP/DOWN” this is
used to lift and
raise the screen
box in place for
maintenance Screen Box
Mesh Change
Up/Down
Up/Down

Hydraulic System
Screen
1. “TAIL CONVEYOR
UP/DOWN” this Tail Conveyor
lever is used to Up/Down
change the height
and discharge
angle of the Tail
Conveyor
2. “TAIL CONVEYOR
FOLD
OPEN/CLOSE” this
lever is used to fold
the Tail Conveyor
away for transport
Tail Conveyor Fold

Open/Close

Hydraulic System Pilot Oil to the
D-6 Valves
2 Station Ce-top
1. The Ce-top is
receiving oil from
the 6 lever manual
control levers when
you select track
mode ON,
2. The oil is then
piloted to the D-6
valves when the
electrical solenoids
are activated.
Pilot Pressure
Relief set at
25Bar

Hydraulic System
Fines Collector
Conveyor
1. The full flow is
allowed to the fines
collector belt but
can be fully
controlled via the
speed control valve
2. The flow control
valve allows full
control over the
Fines conveyor belt
HM8806 Motor Fines Collector

Displacement 630cc (38.44C/In)
Information Rpm 140rpm
Running Pressure Empty 50-80Bar (725 - 1160Psi)
Max Speed 115 M/Min (377.3 ft/Min)
Hydraulic System
Fine Stock Pile

Conveyor
1. The full flow is
allowed to the fines
stockpile conveyor
belt but can be fully
controlled via the
speed control valve
2. The web tech
control allows full
control over the
Fines conveyor belt
Fines Stockpiler
Displacement 395cc (24.1 C/In)
Rpm 220rpm
Running Pressure Empty 50-80Bar (725 - 1160Psi)
Max Speed 160 M/Min (525 ft/Min)

Hydraulic System
Tail Conveyor
1. The full flow is
allowed to the Tail
conveyor belt but
can be fully
controlled via the
speed control valve
2. The flow control
valve allows full
control over the belt
Tail Conveyor
Displacement 490cc X 2 (29.9C/In)
Rpm 90rpm
HM1016 Motor Running Pressure Empty 40 - 60Bar (580 - 870Psi)
Information Max Speed 80 M/Min (262 ft/Min)

Hydraulic System
Mid-Size Conveyor
1. The full flow is
allowed to the Mid-
Size stockpile
conveyor belt but
can be fully
controlled via the
speed control valve
located on the 6
station manifold
Mid Conveyor Motor

Displacement 395ccn (24.1C/In)
RPM 130rpm
Running Pressure Empty 30-40 Bar (435-580 Psi)
Max Speed 95 M/Min (312 Ft/Min)
HM1006 Motor
Information

Hydraulic System
L/H control levers

1. This 6 lever spool
valve is used for
setting the machine
up
Select lever
to view
Sandvik Mining and Construction function
Hydraulic System
Rear Feeder Flair

Down/Up
1. For transportation
the optional hopper
flairs are lowered,
the ram is used to
raise this into the
operational position
The ram
location

Hydraulic System
Maintenance Platform
1. The maintenance
platform is raised
into position with a
hydraulic ram
located in the
centre of the
platform

Hydraulic System
R/H Side Conv Fold

Open/Close
1. This ram will fold
the conveyor out
from the transport
position to the
working position
Fold Ram for the

Mid-Size
Conveyor

Hydraulic System
L/H Side Conv

Down/Up
1. These two rams
fold the conveyor
against the chassis
and are also used
for setting the
conveyor into
different working
positions.

Hydraulic System
Track On/Off
1. When this lever is
selected it diverts
the oil into the Ce-
Top controller and
this in turn supplies
pilot oil to the D-6
Valves

Hydraulic System
R/H control levers

1. This 6 lever spool
valve is used for
setting the machine
up
Select lever
to view
function
Hydraulic System
Feeder Out/In
1. The feeder is
lowered for
transportation to
reduce the
transport height.
2. The rams for
moving the feeder
forwards and
backwards are
enclosed in the box
section frame

Hydraulic System Anti burst
valve
Jacking Legs
1. The jacking legs
are lowered to the
ground for
supporting the
hopper when being
loaded with
material
2. There is a 32 bar
(464Psi) pressure
relief in this circuit
to prevent the
machine being
lifted off the ground
as the jacking legs
are only for extra
stability
32 bar (464Psi)
pressure relief
Hydraulic System
Maintenance Platform
1. The maintenance
platform is raised
into position with a
hydraulic ram
located in the
centre of the
platform

Hydraulic System
R/H Side Conv Fold

Open/Close
1. This ram will fold
the conveyor out
from the transport
position to the
working position
Fold Ram for the

Fines Conveyor

Hydraulic System
R/H Side Conv

The two rams for the conveyor fold
Down/Up
are enclosed in the steel box section
1. These two rams
fold the conveyor
against the chassis
and are also used
for setting the
conveyor into
different working
positions.

Hydraulic System
Rear Feeder Flair

Down/Up
1. For transportation
the optional hopper
flairs are lowered,
the ram is used to
The ram
raise this into the
operational position location

(S5) Qa340

Uploaded by

Copyright:

Available Formats

(S5) Qa340

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

(S5) Qa340

Uploaded by

Copyright:

Available Formats

QA340 (S5)

Hopper & Feeder

Sandvik Mining and Construction

 Heavy duty hydraulically

Sandvik Mining and Construction

 Free swinging fingers

Sandvik Mining and Construction

Sandvik Mining and Construction

 Recessed hopper design

Sandvik Mining and Construction

 The hopper sits on 4

Sandvik Mining and Construction

 Driven from flange

Sandvik Mining and Construction

 Rubber curtain to stop

Sandvik Mining and Construction

 The main conveyor

Sandvik Mining and Construction

Sandvik Mining and Construction

 2 bearing screen box

Sandvik Mining and Construction

Second Box operates as

Clean Gradings at very

Square Mesh Elongated

S-Harp/Diamond Punch Plate

 The screens is driven

Sandvik Mining and Construction

 The Screen box is

Sandvik Mining and Construction

 The top and bottom

Sandvik Mining and Construction

Sandvik Mining and Construction

 Over size discharge chute

Sandvik Mining and Construction

Sandvik Mining and Construction

 Heavy duty belt

Sandvik Mining and Construction

 Heavy duty chevron belt

Sandvik Mining and Construction

 The whole length of the side

Sandvik Mining and Construction

Sandvik Mining and Construction

 Simple user friendly manual

Sandvik Mining and Construction

 Engine fault monitoring

Sandvik Mining and Construction

 The QA340 (S5) is powered by a Duetz

Sandvik Mining and Construction

 370 litre hydraulic tank

Sandvik Mining and Construction

 Simple On/Off type hydraulic

 Direct driven high power

Sandvik Mining and Construction

 Easy engine maintenance access

Sandvik Mining and Construction

 290 litre Diesel Tank

Sandvik Mining and Construction

 Heavy duty “I” beam designed chassis