• Goals of a Fire Prevention Program

• Fire Prevention Strategy

• Housekeeping Issues
• Flammable and Combustible Liquids
• Electrical Fire Hazards
• Compartmentalization
• Life Safety
– The primary goal of fire safety efforts is to protect
building occupants from injury and to prevent loss of
life.
• Property Protection
– The secondary goal of fire safety is to prevent property
damage.
• Protection of Operations
– By preventing fires and limiting damage we can assure
that work operations will continue.
The Strategy of Preventing a Fire
• A fire must have three things to ignite and maintain
combustion:
– Fuel
– Heat
– Oxygen
• The basic strategy of fire prevention is to control or isolate
sources of fuel and heat in order to prevent combustion.
If all three are not present in sufficient quantities a
fire will not ignite or a fire will not be able to
sustain combustion
• Good housekeeping habits are an important part of a safe
workplace.
• Why is good housekeeping important?
– To reduce amounts of flammable and combustible materials.
– To reduce ignition hazards.
– To ensure safe emergency evacuation of occupants.
– To allow for quick emergency response.
 General Housekeeping
Guidelines
• Work areas, aisles, walkways, stairways, and equipment
should be kept clear of loose materials, trash, scraps, etc.
• Never block aisles, fire exits, emergency equipment, or
alarm pull stations with equipment or materials.
• Avoid build up of combustible trash and waste such as
paper, wood, cardboard, etc.
• Keep use and storage of flammables and combustibles to a
minimum.
• Clean up all spills such as grease, oil, or water
immediately. A delay could result in accidents.
 Storage Guidelines
• No storage is allowed in NOTICE
corridors and stairwells. A
Storage
cluttered guidelines
hallway could slow are applicable to all
down emergency evacuation.
locations within ISU buildings and are not
• limited
Storage toexceed
must not storage
a planerooms. This includes
of 18 inches below sprinkler
stored materials in offices, labs, etc.
heads or smoke detectors.
Storage that breaks this plane
may prevent sprinkler heads
from fully covering room A simulated example of how
during a fire. storage can protrude into 18 inch
plane below sprinkler heads.
 Storage Guidelines
• Maintain at least a 3ft clearance
• All storage must be from heating surfaces, air ducts,
at least 3 ft from heaters, and lighting fixtures.
electrical panels. In • Storage of combustible
some emergency materials in mechanical rooms
is prohibited. Improper Mechanical
situations it will be Room Storage
necessary to access Improper Storage in front
these panels of Electrical Panel
quickly.
• Flammable and combustible liquids are potential
fuel sources for fires and are present in almost
every workplace.
• It is actually the vapor created by flammable and
combustible liquids that ignites and burns.
• It is important to understand what materials in
your work area are flammable and combustible so
that you may properly store and isolate them from
ignition sources.
 How do I tell what’s flammable?
• NFPA classification system
– The NFPA diamond is an easy way to determine the safety risks
associated with hazardous materials. To determine a materials
For example, An NFPA
flammability refer todiamond on a of the diamond. A number in
the red section
can ofthis
gasoline
section would have athe3 flammability
will indicate in the rating of the material.
red section indicating that gasoline
•could
Theignite
following
at normal numbering
working system is used to
temperatures.
indicate flammability
0- will not burn
1- must be preheated to burn
2-ignites when moderately heated
3-ignites at normal temperature
4-extremely flammable
NFPA Diamond
 NFPA Classification System
Continued...
• Where can I find NFPA diamonds?
The flashpoint
– Product labels of a liquid is the
lowest temperature at which the
– Material Safety Data Sheets (ask your supervisor for
liquid gives off enough vapor to be
them)
• Howignited. The lower
do I determine thethe flashpoint,of
flammability thechemicals
greater the risk for ignition.
that don’t use the NFPA classification system?
– The flashpoint of a chemical may be used to determine
its flammability. Flashpoint information may be found
on product labels or MSDS sheets.
What’s a
Flashpoint?
 Flammable and Combustible
Liquids Continued...
• Flammable liquids are considered flammable
because their flashpoints are < 100ºF. This means
that flammable liquids burn easily at normal
working temperatures.
• Combustible liquids have a flashpoint at or above
100ºF. These liquids are less hazardous than
flammable liquids but still pose a risk.
• The volatility of flammable and combustible
liquids requires special storage and handling
requirements.
 Storing Flammable and
Combustible Liquids
• Flammable liquids must be stored away from ignition
sources in cool, well ventilated areas away from
incompatible materials
• Limit the amount of flammable and combustible liquids to
the minimum amount necessary.
• As a general rule, No more than 10 gallons of flammable
materials should be outside of approved flammable liquid
storage cabinets or approved storage rooms.
• Room storage limits of flammable and combustible
materials depend on various factors such as sprinklers, and
storage cabinets. Refer to the table on the following slide
for storage guidelines.
 I.S.U. Flammable Liquid Storage
Limits
Table 1. Room Storage Limits for Flammable and Combustible Liquids
Class of Flash Boiling Non Non Sprinkled Sprinkled
Liquid point point Sprinkled Sprinkled Bldg. & Building Bldg./Flammable
(°F) (°F) Building Flammable Liquid Liquid Storage
It may be possible to exceed these Storage Cabinet Cabinet
Class 1A, <73 °F <100 °F 10 gal. 20 gal. 10 gal 40 gal.
Flammables
Class 1B
limits with
<73 °F >100 °F 10 gal.
approval
40 gal.
of 10 gal 80 gal.
Flammables
Class 1C
Environmental
> 73 & NA 10 gal.
Health and10 galSafety. 120 gal.
60 gal.
Flammable <100 °F
Class II >100 To
& NAcontact
30 gal. EH&S
60 gal. by phone
60 gal. dial 90 gal.
Combustibles <140 °F
Class III-A
Combustibles
>140&294-5359.
<200°F
NA 50 gal. 100 gal. 100 gal. 150 gal.

Note: Containers other than safety cans shall not be greater capacity than one (1) gallon. The number of
two (2) gallon safety cans shall not exceed five (5). The number of one (1) gallon safety cans in use
outside storage cabinets shall not exceed ten (10).
 Fire Safety-Electrical Issues
• Electrical hazards are the cause of numerous workplace
fires each year. Faulty electrical equipment or misuse of
equipment produces heat and sparks that serve as ignition
sources in the presence of flammable and combustible
materials.
• Examples of common ignition hazards:
– overloading circuits
– use of unapproved electrical devices
– damaged or worn wiring
 Electrical Fire Safety

• Extension cords
– Extension cords are only approved for temporary use.
They may only be used for a period of three days or
less. Instead of using extension cords contact FP&M to
install permanent wiring.
– When using extension cords check for defaults such as
frays, brittleness, or broken wires.
– Never place extension cords in high traffic areas where
they can be damaged by being stepped on or run over
by equipment.
 Electrical Fire Safety
• Multi-plug strips
– Should only be used for office equipment such as
computers, printers, and fax machines.
– Other common items such as microwaves, refrigerators,
and copy machines must be plugged directly into wall
outlets. This is a requirement of the State Fire Marshal.
– Multi-plug strips should have a fuse or circuit breaker
and be UL approved.
 Electrical Fire Safety
• Avoid the following – Never daisy chain or piggy
improper and hazardous back multi-plug strips and
electrical cords (plugging
practices: strips and cords into each
– Never use three prong other).
adapters that allow a three
pronged plug to plug into a
two prong outlet.
– Never use any item with a
damaged or frayed
electrical cord.
– Space Heaters are not Piggy-backed
allowed in campus multi-plug
buildings. strips
 Compartmentalization
• Buildings are designed to prevent fire, heat, and smoke
from spreading beyond locations of origination. Building
elements such as fire walls, fire dampers, and fire doors,
are designed to seal off one location from the next. This
system is called compartmentalization.
• Compartmentalization increases the safety of evacuating
building occupants because smoke and fire are not able to
escape into exit passageways.
• Containment of fire and smoke reduces property damage
and prevents small fires from growing into large fires.
• In order for compartmentalization efforts to be effective
fire barriers must be maintained.
 What’s A Fire Door?
• Fire doors are designed to
withstand fire, heat and smoke for a
period of 20-minutes to 3 hours.
• Did you know that corridor office
doors are fire doors and should
have a 20 minute rating?
• Corridor laboratory doors should
have a 60 minute rating.
• Fire Doors are required to:
– Be Self Closing: fire doors should
have a door closure that pulls
doors completely shut after the
door has been opened
– Have Positive latching: a positive
latch locks a door in place so can
open swing open freely.
 4 Reasons Not to Wedge Open
Fire Doors
1 For the safety of your buildings 3 To reduce or prevent damage to
occupants. property, research, personal
– If a fire occurs in a location belongings, etc.
where the fire door has been - Keeping your door shut will
wedged, smoke and heat will keep out smoke or fire
travel freely into exit corridors originating in other locations.
hindering or preventing
occupant evacuation.
4 To hold open your door you may
2 It’s State Law have an electro-magnetic device
– Periodically Iowa’s State Fire installed.
Marshal inspects our campus
- This device releases a fire door
and issues numerous citations
upon activation of the fire alarm
for wedging or blocking open
allowing it to close and latch.
doors.
 Maintaining Fire Barriers
• Fire doors need occasional maintenance and repairs to function
properly and should be periodically checked. To test a fire door:
– Open the door fully and allow it to swing shut.
– The door should close and latch completely by itself. Give the door a
push after it closes to ensure that the latch has engaged.
– If the door is not operating properly contact FP&M for repairs.
• Ceiling, Floor, Wall Penetrations
– All areas should be properly sealed to prevent the escape of fire, heat and
smoke.
– Common penetrations include holes in walls, around ducts, pipes, etc.
These types of penetrations should be sealed with appropriate fire-
stopping material.
 Points To Remember
• Housekeeping Issues
– Keep your worksite clean and free of trash and debris.
– Follow For
propermore information or to
storage guidelines.
report
• Flammable hazardous
and Combustible conditions
Liquids
– Use andcontact EH&S
store the minimum at 294-5359
amounts necessary. or
– Follow correct storage guidelines.
visit our website at
• Electrical Fire Hazards
www.ehs.iastate.edu.
– Don’t use unapproved electrical devices.
– Avoid improper uses of multi-plugs.
•
Thanks!
Compartmentalization
– Maintain compartmentalization systems.
– Don’t wedge or block open doors.