CHAPTER 1

www.uthm.edu.my

INTRODUCTION TO
CONCRETE DESIGN
TO EUROCODE
By:
Masni A. Majid
[email protected]

With Wisdom We Explore

 Behavior of Reinforced Concrete
www.uthm.edu.my

 RC is one of the principal materials use in many civil

engineering application.

 Civil Eng. Application :

 Construction of building, retaining walls, foundations, water
retaining structures, highway and bridges.

 It is a composite material, consisting of steel reinforcing bars

embedded in a hardened concrete matrix.

 These two materials have complementary properties.

With Wisdom We Explore

 Behavior of Reinforced Concrete
www.uthm.edu.my

 Concrete :
 Highly in compressive strength but weak in tensile
strength.

 Reinforcement (steel) :
 Highly in tensile strength but weak in compressive
strength.

 By providing steel bars in the zones within a

concrete member which will subjected to tensile
stresses, an economical structural material can be
produced through its composite action.

With Wisdom We Explore

 Behavior of Reinforced Concrete
www.uthm.edu.my

 In addition, the concrete provides corrosion protection and

fire resistance to the embedded steel reinforcing bars.

With Wisdom We Explore

 Reinforced Concrete Element
www.uthm.edu.my

Slab

Beam

Column

Staircase

Foundation

With Wisdom We Explore

 Code of Practice
www.uthm.edu.my

 Document that gives recommendation for the design and

construction of structures.

 It contains detailed requirement regarding actions, stresses,

strengths, design principal and method of achieving the
required performance of completed structure.

 The design procedures, described in this course conform to

the following Eurocode (EC) published by European
Committee for Standardization.

With Wisdom We Explore

 Code of Practice
www.uthm.edu.my

 EN 1990 Eurocode 0: Basis of structural design

 EN 1991 Eurocode 1: Actions on structures
 EN 1992 Eurocode 2: Design of concrete structures

 Eurocode 2 (EC2) applies to the design of buildings and civil

engineering works in plain, reinforced and prestressed
concrete. EC2 comes in several parts as follows:
Eurocode 2 Title
EN 1992 Part 1-1 General rules and rules for buildings
EN 1992 Part 1-2 General rules –Structural fire design
EN 1992 Part 2 Concrete bridges –design and detailing rules
EN 1992 Part 3 Liquid retaining and containment structures

With Wisdom We Explore

 Limit State
www.uthm.edu.my

 The purpose of design is to achieve acceptable probabilities

that a structure will not become unfit for it intended use.
That is, that it will not reach a limit state.
 At any way in which a structure may cease to be fit for use
will constitute a limit state and the design aim is to avoid
any such condition being reached during the expected life of
the structure

 There are two principal types of limit state:

 Ultimate limit state
 Serviceability limit state

With Wisdom We Explore

 Limit State
www.uthm.edu.my

Design situations of limit state

Persistent Design situation during a period of the same

order as he design working life of the structure.
Represents normal use
Transient Design situation during a period much shorter
than the design working life of the structure.
e.g. during execution or repair
Accidental Design situation involving exceptional conditions
for structure. e.g. Fire, explosion, impact etc
Seismic Design situation involving exceptional conditions
for structure during seismic event.

With Wisdom We Explore

 Ultimate Limit State
www.uthm.edu.my

 The conditions that structure must be able to withstand,

with an adequate factor of safety of load for which it is
designed to ensure the safety of the building occupants and
structure itself against collapse, overturning or buckling.
 The ultimate limit state are divided into the following
categories;
 EQU Loss of equilibrium of the structure
 STR Internal failure or excessive deformation of the
structure or structural members
 GEO Failure due to excessive deformation of the ground
 FAT Fatigue failure of the structure or structural members

With Wisdom We Explore

 Ultimate Limit State
www.uthm.edu.my

 For persistent and transient design situation under the STR

limit state, the Eurocode defines three possible combination
as follows;

With Wisdom We Explore

 Serviceability Limit State
www.uthm.edu.my

 Condition in which the structure is damaged and unsuitable

for its intend purposes causing discomfort to the occupants.
 Generally the most important serviceability limit state are:
 Deflection The appearance of efficiency of any part of the
structure must not be adversely affected by
deflections.
 Cracking Local damage due to cracking and spalling must
not affect the appearance, efficiency or durability
of the structure.
 Other limit states which may be reached included
consideration of durability, vibration and fire resistance of
structures.

With Wisdom We Explore

 Characteristic Materials Strength
www.uthm.edu.my

 The strength of materials upon which design is based is such

strength below which results unlikely to fall.
 These are call characteristic strengths.
 It is assumed that for a given material, the variation of
strength will have a normal distribution as shown in figure
below.

With Wisdom We Explore

 Characteristic Materials Strength
www.uthm.edu.my

 The characteristic strength is taken as that value, below

which it is unlikely that more than 5 % of the results will
fails. Thus statistically,

Characteristic Strength = Mean strength – 1.64 (Standard

deviation)
fk = fm – 1.64s

With Wisdom We Explore

 Concrete (Clause 3.1, EC2)
www.uthm.edu.my

 The characteristic strength fck is the 28 days cylinder

strength.

 Table below shows the characteristic cylinder strength of

various classes of concrete recommended for use in
reinforced and prestressed concrete design.

 Class C20/25, for example, refer to cylinder/cube strength of

20 N/mm2 and 25 N/mm2 respectively.

With Wisdom We Explore

 Concrete (Clause 3.1, EC2)
www.uthm.edu.my

 Concrete strength classes and MOE

Source: Table 3.1: MS EN 1992-1-1

With Wisdom We Explore
 Reinforcing steel (Clause 3.2, EC2)
www.uthm.edu.my

 The characteristic strength of steel reinforcement is denotes

by fyk.
 Specified strength for high yield reinforcement given in EC2
is in the range of 400 – 600 N/mm2.
 The most commonly use in the UK is grade 500 and grade
250 plain bar is not now recognized and no longer available
for general used in UK.
 High yield (H) bars may be classified as:
 Class A : which is normally associated with small diameter (≤ 12 mm)
 Class B : which is most commonly used for reinforcing bars.
 Class C : high ductility which may be used in earthquake design.

With Wisdom We Explore

 Partial Safety Factor
www.uthm.edu.my

 Partial safety factor are importance value applied to the

strength of materials and to the actions as to take into
account the possible variation of constructional tolerance.
 The values adopted are based on experience and simplified
calculation and considering the probability of reaching each
limit state.
 Partial safety factor of materials (γm)
Design situation γm for concrete γm for reinforcing steel

Persistent & Transient 1.5 1.15

Accidental 1.2 1.0
Source: Table 2.1N: MS EN 1992-1-1

With Wisdom We Explore

 Partial Safety Factor
www.uthm.edu.my

 Partial safety factor of action, γf

Design Permanent actions (Gk) Variable actions (Qk)
situation Unfavourable Favourable Unfavourable Favourable
Ultimate limit state
Persistent & 1.35 1.0 1.50 0
Transient
Serviceability limit state
All 1.0 1.0
Source: Table A1.2 & A1.4: MS EN 1990

With Wisdom We Explore

 Stress-Strain Curve of Concrete
www.uthm.edu.my

 Concrete used mostly in compression, it compressive stress-

strain curve is of primary importance.
 Typical stress-strain curve of concrete is shown in figure
below:
 The curve is linear in very initial phase of
loading.
 The curve then begin to curve to
horizontal, reach the maximum stress at a
strain of approximately 0.0020 and finally
show a descending nature.

Source: Figure 3.2: MS EN 1992-1-1

With Wisdom We Explore

 Stress-Strain Curve of Concrete
www.uthm.edu.my

 For the design of cross-section, EC2 recommended the used

of idealized stress-strain curve as shown in figure below:

The curve is begin with a parabolic portion

up to a strain εc2, from which point of the
strain increase while the stress remain
constant

Source: Figure 3.3: MS EN 1992-1-1

With Wisdom We Explore

 Stress-Strain Curve of Concrete
www.uthm.edu.my

 The ultimate design compressive stress are given by;

 f ck 0.85 f ck
  0.567 f ck
 mc 1.5
 The coefficient 0.85 takes account of the difference between
bending strength and the cylinder crushing strength of the
concrete.
 The factor of 1.5 is the usual partial safety factor for the
strength of concrete.
 The ultimate strain εcu2 = 0.0035 is typical for classes of
concrete ≤ C50/60.

With Wisdom We Explore

 Stress-Strain Curve of Reinforcing Steel
www.uthm.edu.my

 Steel is high tensile strength material.

 The typical stress-strain curve for hot rolled steel are shown
in figure below:

Source: Figure 3.7(a): MS EN 1992-1-1

With Wisdom We Explore

 Stress-Strain Curve of Reinforcing Steel
www.uthm.edu.my

 For design purpose EC2 recommended the use of idealized

curve shown in figure below:

Source: Figure 3.8: MS EN 1992-1-1

With Wisdom We Explore

 Stress-Strain Curve of Reinforcing Steel
www.uthm.edu.my

 The behavior of the steel is identical in tension and

compression, being linear in the elastic range up to the
design yield stress.
 Design yield tensile stress can be given as;
f yk f yk
  0.87 f yk
 ms 1.15
Where;
fyk = Characteristic yield stress
γms = Partial safety factor of reinforcing steel

With Wisdom We Explore

 Actions
www.uthm.edu.my

 Action is the EC2 terminology for loads and imposed

deformations.
 The characteristic actions are the actual loads that the
structure is designed to carry.
 These are normally thought of as a maximum loads which
will not be exceeded during the life of structure.
 The characteristic actions used in design and defined in EC2
are as follows;
 Characteristic permanent action, Gk
 Characteristic variable action, Qk
 Characteristic wind action, Wk

With Wisdom We Explore

 Characteristic Permanent Action, Gk
www.uthm.edu.my

 Is the selfweight of the structure, weight of finishes, ceiling

and services. Examples of weight of materials as given in EC1
are shown in table below.
Materials Density (kN/m3)

Lightweight concrete 9.0 – 20.0

Normal weight concrete 24.0 – 25.0
Cement mortar 19.0 – 23.0
Wood 3.5 – 10.8
Plywood 4.5 – 7.0
Particle boards 7.0 – 12.0
Steel 77.0 – 78.5
Water 10.0

Source: Table A1-A5: MS EN 1991-1-1

With Wisdom We Explore

 Characteristic Variable Action, Qk
www.uthm.edu.my

 Cause by people, furniture, equipment etc. Which variation in

magnitude with time is considered.
 Example of variable action as given in EC1 are shown in table
below:

With Wisdom We Explore

 Characteristic Variable Action, Qk
www.uthm.edu.my

 For each variable actions there are four representative values:

 Characteristic value, (Qk) – an upper value with an intended probability
of not being exceeded or a lower value with an intended probability of
being achieved, during some specific reference period
 Combination value, (ΨoQk) – value intended to take account of a
reduced probability of the simultaneous occurrence of two or more
variable actions.
 Frequent value, (Ψ1Qk) – value such that it should be exceeded only for a
short period of time and is used primarily for the serviceability limit
states and also accidental limit state.
 Quasi-permanent value, (Ψ2Qk) – value may be exceeded for a
considerable period of time; alternatively it may be considered as an
average loading over time. I is used for a long term affects at the SLS and
also accidental and seismic ULS.

With Wisdom We Explore

 Characteristic Variable Action, Qk
www.uthm.edu.my

Recommended values for Ψ action for building

With Wisdom We Explore

 Design Action
www.uthm.edu.my

 In order to account for variation in Loads due to:

• Errors in the analysis and Design
• Constructional inaccuracies
• Possible load increases
 The characteristic loads Fk (Gk,Qk,Wk) are multiplied by the
appropriate partial safety factor for loads γf to give the
design action acting on the structure.

Fd  Fk   f

 Value of γf are given in EN 1990: Annex A1

With Wisdom We Explore

 Structural Design Process
www.uthm.edu.my

 The first function in design is the planning carried out by the

architect to determine the arrangement and layout of the
building to meet the client’s requirements.
 The structural engineer then determines the best structural
system or forms to bring the architect’s concept into being.
 Construction in different materials and with different
arrangements and systems may require investigation to
determine the most economical answer.
 Architect and engineer should work together at this
conceptual design stage.

With Wisdom We Explore

 Structural Design Process
www.uthm.edu.my

• Once the building form and structural arrangement have

been finalized the design problem consists of the following:
• idealization of the structure into loadbearing frames and
elements for analysis and design
• estimation of actions
• analysis to determine the maximum moments and shears
for design
• design of sections and reinforcement arrangements for
slabs, beams, columns and foundations using the results
from above
• production of arrangement and detail drawings and bar
schedules

With Wisdom We Explore

www.uthm.edu.my

With Wisdom We Explore