Scribd Logo
Upload

Welcome to Scribd!

  • 282 views

    NR 8000

    Uploaded by

    JohannSookdeo
    This document provides steps to configure a ZTE NR8000 MW radio unit for a Digicel project in Trinidad and Tobago. The key steps are: 1. Connect a laptop to the IDU to configure it 2. Set the IP address and login to the web interface 3. Configure system details like the shelf, site ID, frequency and power settings 4. Enable ports as requested and run prepared MPLS and QoS configuration scripts Proper configuration of frequency, power and interfaces is needed to enable antenna alignment and achieve the required link performance.

    Copyright:

    © All Rights Reserved
    Download as PPTX, PDF, TXT or read online from Scribd

    NR 8000

    Uploaded by

    JohannSookdeo
    282 views17 pages
    This document provides steps to configure a ZTE NR8000 MW radio unit for a Digicel project in Trinidad and Tobago. The key steps are: 1. Connect a laptop to the IDU to configure it 2. Set the IP address and login to the web interface 3. Configure system details like the shelf, site ID, frequency and power settings 4. Enable ports as requested and run prepared MPLS and QoS configuration scripts Proper configuration of frequency, power and interfaces is needed to enable antenna alignment and achieve the required link performance.

    Original Description:

    NR8000 Operation Guidev2

    Original Title

    nr8000

    Copyright

    © © All Rights Reserved

    Available Formats

    PPTX, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides steps to configure a ZTE NR8000 MW radio unit for a Digicel project in Trinidad and Tobago. The key steps are: 1. Connect a laptop to the IDU to configure it 2. Set the IP address and login to the web interface 3. Configure system details like the shelf, site ID, frequency and power settings 4. Enable ports as requested and run prepared MPLS and QoS configuration scripts Proper configuration of frequency, power and interfaces is needed to enable antenna alignment and achieve the required link performance.

    Copyright:

    © All Rights Reserved
    Download as PPTX, PDF, TXT or read online from Scribd
    Download as pptx, pdf, or txt
    282 views17 pages

    NR 8000

    Uploaded by

    JohannSookdeo
    This document provides steps to configure a ZTE NR8000 MW radio unit for a Digicel project in Trinidad and Tobago. The key steps are: 1. Connect a laptop to the IDU to configure it 2. Set the IP address and login to the web interface 3. Configure system details like the shelf, site ID, frequency and power settings 4. Enable ports as requested and run prepared MPLS and QoS configuration scripts Proper configuration of frequency, power and interfaces is needed to enable antenna alignment and achieve the required link performance.

    Copyright:

    © All Rights Reserved
    Download as PPTX, PDF, TXT or read online from Scribd
    Download as pptx, pdf, or txt
    of 17

    NR8000 MW Operation Guide for

    Digicel MAKO Project in TnT


    Laptop connect to IDU’s LMT port using LAN cable

    E-mail: [email protected]
    Step 1：Setting IP address as 192.168.1.15 in you laptop

    Step 2：Open the IE browser (Chrome is recommended), input


    the IP: 192.168.1.1, and press Enter, as shown in the figure
    below.

    Step 3：
    User Name : admin Password : admin or User123#
    Click LOGIN
    Introduce : IDU System Detail Menu
    Introduce : NR8250 IDU
    System Detail Menu

    Introduce : NR8120D IDU


    System Detail Menu
    Step 4 (Only for NR8250 IDU)： Setting Shelf (Path: Basic Config -> Shelf)
    Step 5： Click : Basic Config -> System, the page of NE information will display
    Step 6： Setting Site ID, NE Name, Device IP Address follow Design information
    Step 7： Click : Basic Config -> RadioChannel, the page of Channel will display
    Step 8： Setting Tx Frequency, Rx Frequency, Tx Power, Channel Name, Bandwidth, Modulation follow
    Design information

    Antenna alignment can start after this step setting on both sites of
    one link ; RSL must achieve Design Value.
    Step 9 (Only for 2+0 XPIC Link)： Setting PLA (Path: Basic Config -> RadioChannel -> PLA)

    Attention: All the interfaces have been defined in MPLS Script, include Eth Ports, Gbe Ports, RMUF
    interfaces, PLA interfaces . So Please confirm which PLA No. used for which Link from LLD before setting.
    Step 10 (Only for 2+0 XPIC Link)： Setting XPIC (Path: Basic Config -> RadioChannel -> XPIC)

    2+0 XPIC Setting Finished (only step 8 & step 9)!!


    Step 11： Click : Basic Config -> Port, the page of Port will display
    Step 12： Enable the ports that are requested by design
    Introduce : Two scripts will prepare for every IDU, <Site ID>_IDU1.cli script for MPLS setting and <Site ID>_IDU1_MOS.cli
    scipt for QoS setting.
    Step 13：MPLS Setting : Open cmd.exe, enter below red character and Paste MPLS Script

    Remark: You could copy all script and


    paste them in one time!

    Paste MPLS Script on here


    Step 14：QoS Setting : Open cmd.exe, enter below red character and Paste QoS Script

    Remark: You could copy all


    script and paste them in
    one time!

    Here is , not .

    You might also like