General Design Considerations: "Storage Tanks"

General Design
Considerations
“Storage tanks”
Storage facilities are required for:
 Raw materials  Intermediate products  Final products
 Recycle materials  Off-grade materials  Fuels
 A storage tank is a container, usually for holding liquids, sometimes for compressed
gases (gas tank).
 The word "tank" originally meant "artificial lake" and came from India.
 Storage tanks are available in many shapes: vertical and horizontal cylindrical; open top
and closed top; flat bottom, cone bottom.
 Large tanks tend to be vertical cylindrical, or to have rounded corners (transition from
vertical side wall to bottom profile, to easier withstand hydraulic hydrostatically induced
pressure of contained liquid.
horizontal cylindrical tank
vertical cylindrical tank with flat bottom
vertical cylindrical tank with conical bottom
Spherical tanks
 Choice of storage tanks
 Tanks for a particular fluid are chosen according to the flash-point of that substance.
What is a flash point?
 Generally in refineries and especially for liquid fuels, there are:
A) fixed roof tanks, and
B) floating roof tanks.

A) Fixed roof tank
 Used for liquids with very high flash points, (e.g. fuel oil, water, bitumen etc.)
 Cone roofs, dome roofs and umbrella roofs are usual
fixed roof tank

FIXED ROOF TANK
Dome roof tank
Cone roof tank
Umbrella roof tank
Advantages of fixed roof tank:
 Easy to construct and cheap to build.
Disadvantages:
 Material losses due to the escape of vapour.
BREATHING LOSSES OF A FIXED-ROOF TANK

B) Floating roof tanks
The floating roof tanks are developed to store volatile liquids to minimize the loss of
valuable vapors, as well as, to minimize the hazard of dangerous vapor formation
underneath a fixed roof.
Floating roof tanks are broadly divided into:
1) external floating roof tanks (usually called as floating roof tanks: FR Tanks) and
2) internal floating roof types (IFR Tanks).
external floating roof type

external floating roof types
FR tanks do not have a fixed roof (it is open in the top) and has a floating roof only.
Applications of FR tanks:
Medium flash point liquids such as naphtha, kerosene, diesel, crude oil etc. are stored in
these tanks.
2) IFR tanks are used for liquids with low flash-points (eg. gasoline, ethanol). These tanks are
nothing but cone roof tanks with a floating roof (steel disc) inside which travels up and down
along with the liquid level.
 This floating roof traps the vapor from low flash-point fuels.
 Floating roofs are supported with legs on which they rest.
IFR tanks
HARD TOP PAN FLOATING ROOF TANK
Advantages of floating roof tanks:
 Reduce material losses and air pollution.
 Reduce fire and explosion risk due to very small vapour space.
Disadvantages:
 High cost.
Components of IFR tank

 Materials of construction for storage tanks
While steel remains one of the most popular choices for tanks, there are other materials
increasing in popularity such as:
 GRP
 Thermoplastic
 Polyethylene
 Fiberglass
They offer lower build costs and greater chemical resistance, especially for storage of
specialty chemicals.
 Tank Wall Thickness
The tank wall must withstand:
 Hydrostatic pressure of the liquid
 Wind loading
The minimum wall thickness required to resist the hydrostatic pressure can be calculated from
the equation:
where
Tt: tank thickness required at depth HL, mm;
HL: liquid depth, m;
ρL: liquid density, kg/m3;
E: joint efficiency (if applicable);
g: gravitational acceleration, 9.81 m/s2;
St: maximum allowable stress for tank material, N/mm2;
Dt: tank diameter, m.

Important note:
 Since most liquids can spill, evaporate, or seep through even the smallest opening, special
consideration must be made for their safe and secure handling.
 This usually involves building a bunding, or containment dike, around the tank, so that any
leakage may be safely contained. In some cases these area is called the tank farm.
Storage Tanks Farm

Tank failures
There have been numerous catastrophic failures of storage tanks. These failures may
be attributed to:
1. Poor design and construction, with a wall too thin to bear repeated loads from the
contents.
2. The tank had not been tested before use by filling with water, and was also poorly
riveted.
3. Corrosion problem, so storage tanks must be protected against corrosion (e.g cathodic
protection)
4. Faulty welding or by sub-standard steel.

However, storage tanks also present another problem, surprisingly, when empty. If they
have been used to hold oil or oil products such as gasoline, the atmosphere in the tanks may be
highly explosive as the space fills with hydrocarbons. If new welding operations are started,
then sparks can easily ignite the contents, with disastrous results for the welders.
Using an inert gas blanket to prevent explosive atmospheres building up from residues
may solve this problem.
Gas waste handling

General Design Considerations: "Storage Tanks"

Uploaded by

Copyright:

Available Formats

General Design Considerations: "Storage Tanks"

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

General Design Considerations: "Storage Tanks"

Uploaded by

Copyright:

Available Formats

What are the different types of storage tank roofs mentioned?

What are the different types of storage tank roofs mentioned?

What are the advantages and disadvantages of fixed roof tanks?

What are the advantages and disadvantages of fixed roof tanks?

General Design

 Raw materials  Intermediate products  Final products

 Recycle materials  Off-grade materials  Fuels

What is a flash point?

 Generally in refineries and especially for liquid fuels, there are:

A) fixed roof tanks, and

B) floating roof tanks.

fixed roof tank

 Easy to construct and cheap to build.

 Material losses due to the escape of vapour.

BREATHING LOSSES OF A FIXED-ROOF TANK

Floating roof tanks are broadly divided into:

2) internal floating roof types (IFR Tanks).

external floating roof type

 Floating roofs are supported with legs on which they rest.

 Reduce material losses and air pollution.

Components of IFR tank

Tt: tank thickness required at depth HL, mm;

HL: liquid depth, m;

ρL: liquid density, kg/m3;

E: joint efficiency (if applicable);

g: gravitational acceleration, 9.81 m/s2;

St: maximum allowable stress for tank material, N/mm2;

Dt: tank diameter, m.

Storage Tanks Farm

4. Faulty welding or by sub-standard steel.

You might also like