A34620374 - 22805 - 15 - 2018 - Line Coding

Digital Transmission
4-1 DIGITAL-TO-DIGITAL CONVERSION
In this section, we see how we can represent digital

data by using digital signals. The conversion involves
three techniques: line coding, block coding, and
scrambling. Line coding is always needed; block
coding and scrambling may or may not be needed.
Topics discussed in this section:

 Line Coding
 Line Coding Schemes
 Block Coding
 Scrambling
Line Coding
 Converting a string of 1’s and 0’s

(digital data) into a sequence of signals
that denote the 1’s and 0’s.
 For example a high voltage level (+V)
could represent a “1” and a low voltage
level (0 or -V) could represent a “0”.
Figure 4.1 Line coding and decoding
Mapping Data symbols onto
Signal levels
 A data symbol (or element) can consist of a
number of data bits:
 1 , 0 or
 11, 10, 01, ……
 A data symbol can be coded into a single
signal element or multiple signal elements
 1 -> +V, 0 -> -V
 1 -> +V and -V, 0 -> -V and +V
 The ratio ‘r’ is the number of data elements
carried by a signal element.
Relationship between data
rate and signal rate
 The data rate defines the number of bits sent
per sec - bps. It is often referred to the bit
rate.
 The signal rate is the number of signal
elements sent in a second and is measured in
bauds. It is also referred to as the modulation
rate.
 Goal is to increase the data rate whilst
reducing the baud rate.
Figure 4.2 Signal element versus data element
Data rate and Baud rate
 The baud or signal rate can be

expressed as:
S = c x N x 1/r bauds
where N is data rate
c is the case factor (worst, best & avg.)
r is the ratio between data element &
signal element
Example 4.1
A signal is carrying data in which one data element is

encoded as one signal element ( r = 1). If the bit rate is
100 kbps, what is the average value of the baud rate if c is
between 0 and 1?
Solution
We assume that the average value of c is 1/2 . The baud
rate is then
Considerations for choosing a good
signal element referred to as line
encoding
Line encoding C/Cs
 DC components - when the voltage

level remains constant for long periods
of time, there is an increase in the low
frequencies of the signal. Most channels
are bandpass and may not support the
low frequencies.
 This will require the removal of the dc
component of a transmitted signal.
Line encoding C/Cs
 Self synchronization - the clocks at the

sender and the receiver must have the
same bit interval.
 If the receiver clock is faster or slower it
will misinterpret the incoming bit
stream.
Figure 4.3 Effect of lack of synchronization
Example 4.3
In a digital transmission, the receiver clock is 0.1 percent

faster than the sender clock. How many extra bits per
second does the receiver receive if the data rate is
1 kbps? How many if the data rate is 1 Mbps?
Solution
At 1 kbps, the receiver receives 1001 bps instead of 1000
bps.
At 1 Mbps, the receiver receives 1,001,000 bps instead of

1,000,000 bps.
Line encoding C/Cs
 Error detection - errors occur during

transmission due to line impairments.
 Some codes are constructed such that
when an error occurs it can be
detected. For example: a particular
signal transition is not part of the code.
When it occurs, the receiver will know
that a symbol error has occurred.
Line encoding C/Cs
 Noise and interference - there are line

encoding techniques that make the
transmitted signal “immune” to noise
and interference.
 This means that the signal cannot be
corrupted, it is stronger than error
detection.
Line encoding C/Cs
 Complexity - the more robust and

resilient the code, the more complex it
is to implement and the price is often
more than simple one.
Figure 4.4 Line coding schemes
Unipolar
 All signal levels are on one side of the time

axis - either above or below
 NRZ - Non Return to Zero scheme is an
example of this code. The signal level does
not return to zero during a symbol
transmission.
 Scheme is prone to DC components. It has no
synchronization or any error detection. It is
simple but costly in power consumption.
Figure 4.5 Unipolar NRZ scheme
Polar - NRZ
 The voltages are on both sides of the time

axis.
 Polar NRZ scheme can be implemented with
two voltages. E.g. +V for 1 and -V for 0.
 There are two versions:
 NZR - Level (NRZ-L) - positive voltage for one
symbol and negative for the other
 NRZ - Inversion (NRZ-I) - the change or lack of
change in polarity determines the value of a
symbol. E.g. a “1” symbol inverts the polarity a “0”
does not.
Figure 4.6 Polar NRZ-L and NRZ-I schemes
Note
In NRZ-L the level of the voltage

determines the value of the bit.
In NRZ-I the inversion
or the lack of inversion
determines the value of the bit.
Note
NRZ-L and NRZ-I both have an average

signal rate of N/2 Bd.
Note
NRZ-L and NRZ-I both have a DC

component problem, it is worse for NRZ-
L. Both have no self synchronization
&no error detection. Both are relatively
simple to implement.
Polar - RZ
 The Return to Zero (RZ) scheme uses three
voltage values. +, 0, -.
 Each symbol has a transition in the middle.
Either from high to zero or from low to zero.
 This scheme has more signal transitions (two
per symbol) and therefore requires a wider
bandwidth.
 No DC components or baseline wandering.
 Self synchronization - transition indicates
symbol value.
 More complex as it uses three voltage level.
It has no error detection capability.
Figure 4.7 Polar RZ scheme
Polar - Biphase: Manchester and
Differential Manchester
 Manchester coding consists of combining the
NRZ-L and RZ schemes.
 Every symbol has a level transition in the middle:
from high to low or low to high. Uses only two
voltage levels.
 Differential Manchester coding consists of
combining the NRZ-I and RZ schemes.
 Every symbol has a level transition in the middle.
But the level at the beginning of the symbol is
determined by the symbol value. One symbol
causes a level change the other does not.
Figure 4.8 Polar biphase: Manchester and differential Manchester schemes
Note
In Manchester and differential

Manchester encoding, the transition
at the middle of the bit is used for
synchronization.
Note
The minimum bandwidth of Manchester

and differential Manchester is 2 times
that of NRZ. The is no DC component.
None of these codes has error detection.

A34620374 - 22805 - 15 - 2018 - Line Coding

Uploaded by

Copyright:

Available Formats

A34620374 - 22805 - 15 - 2018 - Line Coding

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

A34620374 - 22805 - 15 - 2018 - Line Coding

Uploaded by

Copyright:

Available Formats

Digital Transmission

4-1 DIGITAL-TO-DIGITAL CONVERSION

In this section, we see how we can represent digital

Topics discussed in this section:

 Converting a string of 1’s and 0’s

 The baud or signal rate can be

A signal is carrying data in which one data element is

 DC components - when the voltage

 Self synchronization - the clocks at the

In a digital transmission, the receiver clock is 0.1 percent

At 1 Mbps, the receiver receives 1,001,000 bps instead of

 Error detection - errors occur during

 Noise and interference - there are line

 Complexity - the more robust and

 All signal levels are on one side of the time

 The voltages are on both sides of the time

In NRZ-L the level of the voltage

NRZ-L and NRZ-I both have an average

NRZ-L and NRZ-I both have a DC

In Manchester and differential

The minimum bandwidth of Manchester

You might also like