Topic 4: Physical Layer: Business Data Communications, 4e

Topic 4: Physical Layer
- Chapter 7: Transmission Media
Business Data Communications,

4e
Classes of Transmission Media
Conducted or guided media
 use a conductor such as a wire or a fiber
optic cable to move the signal from sender
to receiver
Wireless or unguided media
 use radio waves of different frequencies
and do not need a wire or cable conductor
to transmit signals
Design Factors
for Transmission Media
Bandwidth: All other factors remaining constant, the
greater the band-width of a signal, the higher the
data rate that can be achieved.
Transmission impairments. Limit the distance a signal
can travel.
Interference: Competing signals in overlapping
frequency bands can distort or wipe out a signal.
Number of receivers: Each attachment introduces
some attenuation and distortion, limiting distance
and/or data rate.
Electromagnetic Spectrum for
Transmission Media
Guided Transmission Media
Transmission capacity depends on the

distance and on whether the medium is
point-to-point or multipoint
Examples
 twisted pair wires
 coaxial cables
 optical fiber
Twisted Pair Wires
Consists of two insulated copper wires
arranged in a regular spiral pattern to
minimize the electromagnetic
interference between adjacent pairs
Often used at customer facilities and
also over distances to carry voice as
well as data communications
Low frequency transmission medium
Types of Twisted Pair
STP (shielded twisted pair)
 the pair is wrapped with metallic foil or
braid to insulate the pair from
electromagnetic interference
UTP (unshielded twisted pair)
 each wire is insulated with plastic wrap,
but the pair is encased in an outer covering
Ratings of Twisted Pair
Category 3 UTP
 data rates of up to 16mbps are achievable
Category 5 UTP
 data rates of up to 100mbps are achievable
 more tightly twisted than Category 3 cables
 more expensive, but better performance
STP
 More expensive, harder to work with
Twisted Pair Advantages
Inexpensive and readily available
Flexible and light weight
Easy to work with and install
Twisted Pair Disadvantages
Susceptibility to interference and noise
Attenuation problem
 For analog, repeaters needed every 5-6km
 For digital, repeaters needed every 2-3km
Relatively low bandwidth (3000Hz)
Coaxial Cable (or Coax)
Used for cable television, LANs,
telephony
Has an inner conductor surrounded by a
braided mesh
Both conductors share a common
center axial, hence the term “co-axial”
Coax Layers
outer jacket
(polyethylene)
shield
(braided wire)
insulating material
copper or aluminum
conductor
Coax Advantages
Higher bandwidth
 400 to 600Mhz
 up to 10,800 voice conversations
Can be tapped easily (pros and cons)
Much less susceptible to interference
than twisted pair
Coax Disadvantages
High attenuation rate makes it
expensive over long distance
Bulky
Fiber Optic Cable
Relatively new transmission medium used by
telephone companies in place of long-
distance trunk lines
Also used by private companies in
implementing local data communications
networks
Require a light source with injection laser
diode (ILD) or light-emitting diodes (LED)
Fiber Optic Layers
consists of three concentric sections
plastic jacket glass or plastic fiber core

cladding
Fiber Optic Types
multimode step-index fiber
 the reflective walls of the fiber move the light
pulses to the receiver
multimode graded-index fiber
 acts to refract the light toward the center of the
fiber by variations in the density
single mode fiber
 the light is guided down the center of an
extremely narrow core
Fiber Optic Signals
fiber optic multimode

step-index
fiber optic multimode

graded-index
fiber optic single mode

Fiber Optic Advantages
greater capacity (bandwidth of up to 2

Gbps)
smaller size and lighter weight
lower attenuation
immunity to environmental interference
highly secure due to tap difficulty and
lack of signal radiation
Fiber Optic Disadvantages
expensive over short distance
requires highly skilled installers
adding additional nodes is difficult
Wireless (Unguided Media)
Transmission
transmission and reception are achieved by
means of an antenna
directional
 transmitting antenna puts out focused beam
 transmitter and receiver must be aligned
omnidirectional
 signal spreads out in all directions
 can be received by many antennas
Wireless Examples
terrestrial microwave
satellite microwave
broadcast radio
infrared
Terrestrial Microwave
used for long-distance telephone service
uses radio frequency spectrum, from 2 to 40
Ghz
parabolic dish transmitter, mounted high
used by common carriers as well as private
networks
requires unobstructed line of sight between
source and receiver
curvature of the earth requires stations
(repeaters) ~30 miles apart
Satellite Microwave
Applications
Television distribution
Long-distance telephone transmission
Private business networks
Microwave Transmission
Disadvantages
line of sight requirement
expensive towers and repeaters
subject to interference such as passing
airplanes and rain
Satellite
Microwave Transmission
a microwave relay station in space
can relay signals over long distances
geostationary satellites
 remain above the equator at a height of
22,300 miles (geosynchronous orbit)
 travel around the earth in exactly the time
the earth takes to rotate
Satellite Transmission Links
earth stations communicate by sending
signals to the satellite on an uplink
the satellite then repeats those signals
on a downlink
the broadcast nature of the downlink
makes it attractive for services such as
the distribution of television
programming
Satellite Transmission Process
satellite
transponder
dish dish
22,300 miles
uplink station downlink station

Satellite Transmission
Applications
television distribution
 a network provides programming from a
central location
 direct broadcast satellite (DBS)
long-distance telephone transmission
 high-usage international trunks
private business networks
Principal Satellite Transmission
Bands
C band: 4(downlink) - 6(uplink) GHz
 the first to be designated
Ku band: 12(downlink) -14(uplink) GHz
 rain interference is the major problem
Ka band: 19(downlink) - 29(uplink) GHz
 equipment needed to use the band is still
very expensive
Fiber vs Satellite
Radio
radio is omnidirectional and microwave
is directional
Radio is a general term often used to
encompass frequencies in the range 3
kHz to 300 GHz.
Mobile telephony occupies several
frequency bands just under 1 GHz.
Infrared
Uses transmitters/receivers
(transceivers) that modulate
noncoherent infrared light.
Transceivers must be within line of sight
of each other (directly or via reflection
).
Unlike microwaves, infrared does not
penetrate walls.

Topic 4: Physical Layer: Business Data Communications, 4e

Uploaded by

Copyright:

Available Formats

Topic 4: Physical Layer: Business Data Communications, 4e

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Topic 4: Physical Layer: Business Data Communications, 4e

Uploaded by

Copyright:

Available Formats

Topic 4: Physical Layer

- Chapter 7: Transmission Media

Business Data Communications,

Transmission capacity depends on the

plastic jacket glass or plastic fiber core

fiber optic multimode

fiber optic multimode

fiber optic single mode

greater capacity (bandwidth of up to 2

uplink station downlink station

You might also like