Galaxy S5 H/W Repair Guide: March, 2014

Galaxy S5 H/W Repair Guide
March, 2014
This material is a property of Samsung Electronics Co., Ltd. Any unauthorized use of this material can be punished
under applicable International and/or domestic law.
- This document cannot be used without Samsung’s Authorization -
Notice
All functionality, features, specifications and other product information provided in this
document including, but not limited to, the benefits, design, pricing, components,
performance, availability, and capabilities of the product are subject to change without
notice or obligation.
Samsung reserves the right to make changes to this document and the product described
herein, at anytime, without obligation on Samsung to provide notification of such change.

Contents
1. Introduction of GALAXY S5
2. Repair Guide
• Disassembly & Assembly
• Electronic Components
• Trouble Shooting
3. Service Guide
• RF calibration
• Binary Download
• Boot Recovery
4. Q&A

Introduction of GALAXY S5
Charcoal Black
Shimmery White
Copper Gold
Electric Blue

Introduction of GALAXY S5
Specification
Item spec.
- Dimensions : 142 x 72.5 x 8.1mm, 145g
BODY - IP67 certified (dust and water resistant)
- Water resistant up to 1 meter and 30 minutes
AP Chipset - Quad-core 2.5GHz Krait 400 CPU, Adreno 330 GPU
- 4G : LTE 800/850/900/1800/1900/2100/2600 (Cat4 : 50 Mbps UL, 150 Mbps DL)

Network - 3G : HSDPA 850/900/1900/2100 (HSDPA 42.2Mbps, HSUPA 5.76Mbps)
- 2G : GSM 850/900/1800/1900
OS Android OS V4.4.2(KitKat)
Memory 16GB/32GB FLASH + LPDDR3 2GB RAM
Display 5.1” FHD sAMOLED (1920x1080), 432ppi
Camera 16MP phase detection AF (1080p@60fs) + 2MP (1080p@30fps)
Accelerometer, Magnetic, Gyro, Barometer, RGB Light, Proximity, Gesture

Sensor
Fingerprint Scanner, Heart Rate Sensor
Connectivity BT4.0, WLAN a/b/g/n/ac, NFC, MHL, USB3.0, Remote Controller
GPS A-GPS support and GLONASS
Battery 2,800mAh
Micro SD Yes (Up to 128GB)
SIM Micro-SIM
Disassembly & Assembly Instruction
Disassembly
& Assembly
Instruction

Guide of disassembly

Pre-requisite
Screw driver Disassembly knife Glass Absorber Anti-static mat
Tweezers Anti-static gloves Ethyl Alcohol Mobile Dryer

Disassemble Home key Cover & Connector
1 2
Do NOT use sharp tweezers

Put the device into the Dryer
Temperature: 80℃
Time: 10minutes

Disassemble OCTA unit from the Rear case

2 4
Home key
Connector
Use 2 absorbers Detach Cu tape from Cu sheet

not to separate LCD from TSP
1 5
Detach tape with knife
Do NOT push too deeply
Do NOT pull too strong

LCD Connector

Remove Tapes from the OCTA & Bracket
Do NOT use tweezers or any sharp tools

Remove Tapes from the Rear outside

Use Ethyl Alcohol with cotton swab

Disassemble Bracket from the Rear case

②
① ①
Total 13 points
Be careful not to bend bracket,
especially Battery plate
③

Disassemble PBA from the Bracket

1
Disassemble
connector
Disassemble Sub PBA from the Bracket

1 Work via disassembly hole
Detach with tweezers

via disassembly hole

Disassemble Home key from the OCTA
Remove all remained substance

Detach Cu sheet from the OCTA
Detach and replace Cu sheet

if severe damage on it
Watch out LCD damage

Disassemble Ear jack & Speaker from the Rear
Remove all remained substance

Disassemble Motor from the Bracket

Guide of assembly

Guide of assembly
Pre-requisite
Screw driver Tape attach JIG Glass Absorber Anti-static mat
Tweezers Anti-static gloves Window Press JIG Window Press Pad

Guide of assembly
Attach Cu sheet on the OCTA

Guide of assembly
Assemble Home key on the OCTA

3
1
4
Press FPCB
to attach tape
Remove vinyl
Press Home key
to attach tape
Remove vinyl Fold up FPCB

Guide of assembly
Assemble Ear jack & Speaker on the Rear
Join on the 1 guide point
Press Speaker enough

Guide of assembly
Assemble Motor on the Bracket

Guide of assembly
Assemble Sub PBA on the Bracket

1
Remove vinyl
2 3
5
Join on 3 guide points
6 Remove paper
4
7
Fold up FPCB

Guide of assembly
Assemble PBA on the Bracket

1
Assemble
connector

Guide of assembly
Assemble Bracket on the Rear case

③
② ②
Total 13 points
Do NOT push Battery plate

Guide of assembly
Attach Foam tape on the OCTA unit

2 4
Top: RCV
Press outside enough
Bot: Home
1 3 5

Guide of assembly
Attach Cu tape on the Bracket

Guide of assembly
Assemble OCTA unit on the Rear case

5
1
3
RCV hole
4
Remove vinyl Use Absorber to avoid
finger interference
Home key
Connector
LCD Connector
Press OCTA outside

Guide of assembly
Connect Home key and Assemble Cover

Guide of assembly
Press OCTA Window (with JIG)

Press the Window
Camera Home key
By rotating wheel
Force: 1N
Time: 1minute

Guide of assembly
Press OCTA Window (manually)
Camera Home key

2 3 4
1,5 1,5
2 3 4
Approx. 40kg
Press each for 15 sec

Electronic Components
Electronic
Components

Electronic Components (1/5)
SUB ANT
(DRX B7 + GPS) SUB ANT
(DRX B1/2/3/5/8/20 +
BT/WIFI)
SIM + microSD
FLASH LED + SOCKET
HRM SENSOR 16M CAM
BATTERY
ACCESSARY (2,800mAh)
CONTACT PINS
SPEAKER
MAIN ANT

2ND MIC HOLE
ANT CONTACT
ANT CONTACT
POWER KEY
VOLUME KEY
GRAPHITE
EAR-JACK
RECEIVER SHEET
IR LED
WINDOW SPEAKER
ANT CONTACT
MAIN MIC HOLE

FRONT CAM
MOTOR
16M CAM
VOLUME
MAIN PBA KEY FPCB
OCTA
BRACKET
COAXIABLE
CABLE1,2 Fingerprint
HOME KEY
FPCB
SUB PBA


RGB / PROXIMITY /
GESTURE SENSOR
HRM
NFC
CAMERA
BT / WIFI
SENSOR
MHL AUDIO CHARGING /
HUB
SUB PMIC /
DISPLAY POWER
AP POWER AP / MEMORY
BLOCK
RF BLOCK

SMD parts (TOP side)
ANT400 MIC801
Ant. Contact (for GPS) SUB MIC
ANT815/816 ANT1101/1102
RCV Contact Ant. Contact (for Sub Ant.1)
U407 ANT401/402
Magnetic Sensor Ant. Contact (for BT/WIFI)
U410 F1107
NFC CRX MLB LNA
(BAND1/2/3/5/8/20)
ANT1100/1103
Ant. Contact (for Sub Ant.2) ANT401/402
Ant. Contact (for BT/WIFI)
U804
Audio Codec SIM600
SIM/SD CARD SOCKET
ANT806/807
Power key Contact U400
HRM SENSOR
U7002
GPIO Expander LED7000
Flash LED
U406 ANT403/404/7000/7001/7005
6 Axis Sensor (GYRO,ACCEL) COVER Contact ANT808/811/812/813/814
Earjack Contact
U403
U7003
SENSOR Hub BTC7000
PMIC
Battery Connector
U1001
U302
MHL 2.0 U105
Transceiver
SUB MLB SW
U7004
(BAND1/2/3/5/8/20)
FPGA
F102
U803
BAND1 PRX
2-MIC CHIP
F101
U103
MAIN FEMID
MAIN SWITCH
(BAND1TX/2/3/5/8/20)
(BAND7/38/40/B1 PRX)
HDC400
U901
BTP IF Conn
OVP IC

SMD parts (Bottom side)
LED1000 U1000
SVC LED Gesture Sensor
IRDA1000 U404
IRDA Barometer Sensor
U1104 HDC900
RF Switch (BAND1/2/3) VT Camera Connector
U1109 HDC901
RF Switch (BAND5/8/20) 16M Camera Connector
ANT803/804/805 U903
Volume key Contact DC/DC DDI_Core 1.5V
U405 HDC902
BT/WIFI OCTA Connector
ANT800/801 U900
Vibration Motor Contact OCTA DC-DC
U904 UCP500(upper part)
Companion IC POP MEMORY
U7005 UCP500(lower part)
Ext.Buck for 16M Camera Application
& Communication
U7000
Proccesor
IF PMIC
UME6000
U7006
eMMC MEMORY
SUB PMIC
PA201
U301 (in Shieldcan)
BAND7 PAD (PA+DPX)
PA PMIC
PA200
U907
BAND1/2/3/5/8/20, GSM
Load Switch
QUAD MMMB PA
U805
HDC903
MAIN MIC Bias LDO
SUB FPCB IF Connector

Trouble Shooting
Trouble Shooting

Test Mode
Check the symptom

-> *#0*#

Power problem
Step Check point Result value Defect point

1 Confirm the defect symptom - -
Solved Battery
2 Check the power with a new battery
Not solved Go to the next step
Check the PBA current with a power supply High current (over 1A) Circuit short
3
(power supply voltage : 3.8 ~ 4.0V) No current (almost 0mA) Go to the next step
C7030 = 3.8V
Go to the next step
4 Check the voltage of U7000(C7030) (same as power supply voltage)
If not the correct value IF PMIC (U7000)
C7023 = 1.8V Go to the next step
5 Check the voltage of PMIC output.
If not the correct value MAIN PMIC (U7003)
19.2MHz Main chip (UCP500)
6 Check the frequency of OSC7000
If not the correct value X-TAL (OSC7000)

Power problem
Step4 Step5
U7000
C7030 U7003
C7023
OSC7000
Step6
UCP500

RF (GSM,WCDMA, LTE)
Confirm the defect symptom

1
(Make a call, check the debug screen *#0011# )
- -
Abnormal Settings
Check the settings
2
(airplane mode, Mobile networks)
Normal Go to the next step
Broken, dust, corrosion Coaxial cable

Check the status coaxial cable & main ANT & No insert Main ant, diversity ant
3
diversity ant.
Power on with a power supply

4 - -
(power supply voltage : 3.8V)
Check the status(crack, missing, Corrosion..etc) Abnormal status

of RF components. RF components.
(compared with a good PBA)
U302 Transceiver
5
F101 Main FEMID CP(Call Processor)
PA200 PAM(Power Amplitude Module) Normal status
(UCP500)
F1107 Sub FEM (compared with a good PBA)
CP PMIC(U7003)
U301 PA DCDC

RF (GSM,WCDMA,LTE)
Step2 Step3
Coaxial cable
(connect Main Ant.
with PBA)
CHECK SETTINGS
Main
DEBUG SCREEN ANTENNA contact
STATUS
Same value compared
CHECK SIM card &
SOCKET STATUS
with normal device. Step5 ANT. Contact (for main RF)
U301 PA DCDC
Step3
F1107 Sub Fem
Diversity U302 Transceiver

ANTENNA contact
F101 Main FEMID
PA200 PAM(Power
Amplitude Module)

BT/WIFI
Confirm the defect symptom Turned on Go to the next step

1
(Check the turned on BT/WIFI & connected device) Turned off Turn on
Ant & ANT401,
Check the BT/WIFI Ant. & Ant contact. Broken, dust, corrosion
2 ANT402
(Rear cover Ant. & ANT401, ANT402)
3 - -
Check the voltage of C427 C427 = ~1.8V Go to the next step
4
Notice. It should be measured when the BT/WIFI
path is activated on If not the correct value PMIC (U7003)
Check the voltage of C428 C428 = ~1.5V BT/WIFI IC (U405)

5
Notice. It should be measured when the BT/WIFI L410
path is activated on If not the correct value
or BT/WIFI IC (U405)

BT/WIFI
Step1 Step2
BT/ WIFI ANTENNA
CONTACT ANT402
BT/ WIFI ANTENNA

(LDS TYPE)
WIFI 2nd ANTENNA

(LDS TYPE) WIFI 2nd ANTENNA ANT401
CONTACT
Step4 & 5
BT/ WIFI IC
L410
C427
C428
U7003 (PMIC)

NFC

1
(Check the turned on NFC function) Turned off Turn on
Broken, dust, corrosion,
Check the status of BATTERY BATTERY
2 wrong
(NFC Antenna is in BATTERY)
3 - -
Check the voltage of R419 R419=1.8V Go to the next step
4
Notice. It should be measured when the NFC path is
activated on If not the correct value PMIC (U7003)
R7004 = 19.2Mhz
Check the clock of R7004 MAIN CHIP(UCP500)
(Same signal compared with
or NFC Chip(U410)
5 a good PBA)
Notice. It should be measured when the NFC path is
activated on PMIC (U7003)
If not the correct value
or OSC7000

NFC
Step1,2
CHECK SETTING
Check the status of battery

(NFC Antenna is in battery)
Step 4,5 Check NFC power line
R419
U401
UCP500
R7004

GPS/GLONASS

1
(Check the turned on GPS function) Turned off Turn on
ANT400
Broken, dust, corrosion
2 Check the status ANT400, GPS ANT & Contact GPS ant
3 - -
Check the voltage of C406 C406 = 2.8V Go to the next step
4
Notice. It should be measured when the GPS path is
activated on If not the correct value PMIC(U7003)
Check the voltage of C405 C405= 1.8V Go to the next step

5
activated on If not the correct value Main Chip(UCP500)
C308 = 19.2Mhz
Check the clock of C308 GPS IC(U302)
(Same signal compared with
GPS LNA(U402)
6 a good PBA)
activated on PMIC (U7003)
If not the correct value
or OSC7000

GPS / GLONASS
Step1 Step2
ANT400
GPS ANTENNA
GPS ANTENNA
(LDS Type)
Contact
Step4,5,6
U402 UCP500
C406
C308 C405

Main Camera problem
Broken, dust, corrosion Main cam connector
2 Check the Main Camera connector (HDC901) Insert status (HDC901)
Solved Main Camera
3 Replace the Main Camera Module
Connect a Main camera , and Camera on with a
4 power supply - -
Check the voltage of C907 = 1.2V, C910 = 2.8V If not the correct value PMIC(U7003)
5 Notice. It should be measured when the Camera is
activated on C907 = 1.2V, C910 = 2.8V Go to the next step
Check the voltage of C908 = 1.8V, C909 = 2.95V, If not the correct value SUB PMIC(U7006)
C950 = 1.0V, C917V = 1.8V
6 C908 = 1.8V, C909 = 2.95V
Notice. It should be measured when the Camera is Go to the next step
activated on C950 = 1.0V, C917V = 1.8V
Check the voltage of following chips If not the correct value U7005 or L7015
(C902 = 0.875~1.0V)
7
Notice. It should be measured when the Camera C902 = 0.875~1.0V Go to the next step
is activated on
Check the voltage of following chips If not the correct value Replace the PBA
(R916 = 24MHz)
8
Notice. It should be measured when the Camera R916 = 24MHz MAIN CHIP
is activated on

Main Camera problem
Step2 Step5, 6
Main CAM CONN
HDC901
C910
C909
C907 C908
Step6, 7 Step8
C950
C902
R916
C917

Display problem

Broken, dust, corrosion AMOLED connector
2 Check the AMOLED connector (HDC902) Insert status (HDC902)
Solved AMOLED
3 Replace the AMOLED
Connect a AMOLED, and display on with a
4 power supply - -
Check the voltage of C906 = 3.0V If not the correct value PMIC(U7003)
5 Notice. It should be measured when the display is
activated on C906=3.0V Go to the next step
Check the voltage of C921 = 1.5V If not the correct value U903
6 Notice. It should be measured when the display is
activated on C921=1.5V Go to the next step
Check the voltage of following chips If not the correct value U900
(C903,C919,C920) C903 = 7.0V
7
Notice. It should be measured when the display C919 = -1.4 ~ -4.4V MAIN CHIP
is activated on C920 = 4.6V

Display problem
Step2 Step5, 6
LCD CONNECTOR
HDC902
C906
U900 C921
Step7
C903
C919 C920

Touch problem

AMOLED connector
Broken, dust, corrosion
2 Check the AMOLED connector (HDC902) (HDC902)
Solved TSP
3 Replace the OCTA
Connect a LCD and display on with a power
4 - -
supply (power supply voltage : 4.0V)
Check the voltage of following chips If not the correct value PMIC(U7003)
(C911,C922)
5
Notice. It should be measured when the C911 = 1.8V
Go to the next step
display is activated on C922 = 3.3V
Check the Signal of following chips If not the correct value R506,R508
(R506,R508)
6
Notice. It should be measured when the Same signal compared with a
display is activated on MAIN CHIP or PBA
good PBA

Touch problem
LCD(include TSP)
CONNECTOR
C911
C922
U7003
R508
R506

Speaker problem
Step. Check point Result value Defect point
1 Confirm the defect symptom. - -
Make a factory reset (Setting→Backup and Solved Setting error

2
reset→Factory data reset). Not solved Go to the next step
Replace the speaker(3001-002733), and also Solved speaker
3 replace the Assy case-rear(GH98-32015A) to
use a new speaker tape. Not solved Go to the next step
Connect a LCD, and power on with a power

4 supply. - -
Activate the speaker path.
5 - -
(*#0*# → Speaker)
Same signal compared with a
Check the signal at two of speaker contacts. Go to step 7
good PBA
6 Notice. It should be measured when the
speaker path is activated on No signal Go to step 8
Check if the SPK is contacted to SUB PBA Solved Assembly error

7 (GH96-07020A) well, and assemble the phone
again. Not solved Go to step 3
Solved SUB PBA

Check if the connector HDC903 is connected
8
well, and If yes, replace the SUB PBA.
Not solved Audio Codec (U804)

Speaker problem
Step3 Step6
Assy SUB PBA

(GH96-07020A)
Assy case-rear Speaker contacts
(GH98-32015A)
Speaker (3001-002733)
Step8
Reverse
U804
HDC903
Audio Codec
Connector

Receiver problem

1 Confirm the defect symptom. - -
Make a factory reset (Setting→Backup and Solved Setting error

2
reset→Factory data reset). Not solved Go to the next step
Broken, dust, corrosion connector
3 Check the receiver connector (ANT815, ANT 816)
Solved Receiver
4 Replace the Assy case-rear(GH98-32015A).
Connect a LCD, and power on with a power
5 supply. - -
Activate the Receiver path.
6 - -
(*#0*# → Receiver)
Check the signal at ANT815, ANT 816. Same signal compared with a
Go to the next step
good PBA
7
Notice. It should be measured when the Audio codec
Receiver path is activated on No signal
(U804)
Make a call of speaker mode, and check if the Okay 2-MIC Chip (U803)
8
speaker sound is okay. Not okay Modem (UCP500)

Receiver problem
Step3 Step4
Receiver
Assy case-rear
(GH98-32015A)
Receiver connector
(ANT815, ANT 816)
Step7, Step8
U803
2-MIC Chip
U804
Audio Codec

Microphone problem

- -
1 Confirm the defect symptom.
- -
Dust Clean the hole
2 Check the microphone hole.
Wrong insert Re-insert
3 Check the microphone rubber.
Activate the MIC path. (Choose one of the option below)
4 - Open Camera App. → Start Camcording - -
- *#0283# → Loopback Test Start
Check the voltage of MIC bias 1.8V Go to the next step
- Main MIC : on C825
- SUB MIC : on C830 - Main MIC :
5
MIC LDO(U805)
Notice. It should be measured when the microphone If not the correct value
- SUB MIC :
path is activated on Audio codec(U804)
Check the signal of MIC CLK / Data
No CLK Signal Audio codec(U804)
- Main MIC : on C951 / C952
- SUB MIC : on ZD800 / ZD801
6
CLK signal exist, but no
Notice. It should be measured when the microphone MIC
data signal
path is activated on

Microphone problem
Step2,3
Microphone Microphone
Rubber Holder
Step5, 6 Microphone signal path
C951 / MIC CLK
U805
MIC LDO
C952 / MIC DATA
C825 / MIC BIAS

Sensor problem

Confirm the defect symptom
1 - -
(*#0*# -> Sensor)
Solved Oscillator(OSC400)
2 Check the oscillator(Frequency = 32.768kHz)
Solved Sensor Hub(U403)
3 Check the I2C lines(R504, R505, R507, R509)
Not solved Sensor
Caution: Temperature/Humidity sensor should not be directly exposed to the heat-gun when you replace
USB connector, because excessive heat can cause abnormal operation of the sensor. The temperature th
at Temperature/Humidity sensor sees should not exceed 260°C. Use proper heat-shielding material to pro
tect Temperature/Humidity sensor

Sensor problem
Step1 Step2,3
I2C Pull up
Resistor
I2C Pull up
Resistor
*#0*#
Sensor Sensor hub
Oscillator
Sensors
Accelerometer & Gyro Gesture & Proximity & RGB Magnetic HRM
Barometer

RF Calibration & S/W Download
RF Calibration
S/W Download

CMW500 RF CAL SETUP (SM-G900F, LTE)
Power Divider RF CABLE

50ohm Termination
(1 for PRX, 1 for DRX)
RF calibration(1/5) (except barometer cal.)
★ For Galaxy S5(SM-G900F), new IF cable should be used for IMEI writing and
Calibration. (It is same with GT-I9505’s cable. (Galaxy S4)
1. Download Factory Binary for calibration
2. Run Calibration program.

Category Filename Remark
Launcher DASEUL_Launcher_v3.0.22.exe
Folder Name : SM-G900F
Runtime file DASEUL_CAL_ALL_Runtime_3.1.108.0_r00093.CAB
(under Launcher folder)
SM-G900F_OPEN_CALIBRATION_Ver_3.1.104.6.CAB Folder Name : SM-G900F
Model File
or later version (under Launcher folder)

1) Run Daseul Launcher Program

2) Select Sequence Files and click Start.
3) Check ‘Calibration’

4) Click ‘Hardware Config’ option and Select Port number like capture.
5) Click Save and OK to enter Calibration program.

6) Click ‘START’ button and check if “Running” message appears.

USER Binary Download
1. Run the “Odin3 v3.09.exe

2. Open SW files (PIT, BL, AP, CP, CSC)
3. Enter into Download mode.
- press volume-down + Home + Power key simultaneously.
- press volume-up key when the warning screen comes up.
4. Connect the phone to PC using USB cable.
5. Click Start button when the phone is attached to PC.
Boot Recovery (1/5) – SM-G900F
- Brief Process of Boot Recovery

1) Make T-Flash card for boot recovery.
2) Turn on the defective phone with T-Flash card inserted.
3) Download full S/W when the defective phone enters download mode automatically.
- Preparations
1) One normal SM-G900F phone
2) One micro-SD CARD (4GB↑)
3) Odin3 v3.09.exe
4) MSM8974PRO_boot_recovery.pit
5) Bootloader.tar.md5

※ Download bootloader file into T-Flash card using normal phone.

※ Screen of downloading with T-Flash card

※ Turn on the defective device with the T-Flash Card inserted.
It will automatically make the device go into the download mode.

※ Download full S/W.

Q&A
Question

Galaxy S5 H/W Repair Guide: March, 2014

Uploaded by

Copyright:

Available Formats

Galaxy S5 H/W Repair Guide: March, 2014

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Galaxy S5 H/W Repair Guide: March, 2014

Uploaded by

Copyright:

Available Formats

Galaxy S5 H/W Repair Guide

herein, at anytime, without obligation on Samsung to provide notification of such change.

- This document cannot be used without Samsung’s Authorization -

- This document cannot be used without Samsung’s Authorization -

- This document cannot be used without Samsung’s Authorization -

AP Chipset - Quad-core 2.5GHz Krait 400 CPU, Adreno 330 GPU

- 4G : LTE 800/850/900/1800/1900/2100/2600 (Cat4 : 50 Mbps UL, 150 Mbps DL)

Memory 16GB/32GB FLASH + LPDDR3 2GB RAM

Display 5.1” FHD sAMOLED (1920x1080), 432ppi

Camera 16MP phase detection AF (1080p@60fs) + 2MP (1080p@30fps)

Accelerometer, Magnetic, Gyro, Barometer, RGB Light, Proximity, Gesture

- This document cannot be used without Samsung’s Authorization -

- This document cannot be used without Samsung’s Authorization -

Tweezers Anti-static gloves Ethyl Alcohol Mobile Dryer

- This document cannot be used without Samsung’s Authorization -

Disassemble Home key Cover & Connector

Do NOT use sharp tweezers

- This document cannot be used without Samsung’s Authorization -

Put the device into the Dryer

- This document cannot be used without Samsung’s Authorization -

Disassemble OCTA unit from the Rear case

Use 2 absorbers Detach Cu tape from Cu sheet

Do NOT pull too strong

- This document cannot be used without Samsung’s Authorization -

Remove Tapes from the OCTA & Bracket

Do NOT use tweezers or any sharp tools

- This document cannot be used without Samsung’s Authorization -

Remove Tapes from the Rear outside

- This document cannot be used without Samsung’s Authorization -

Disassemble Bracket from the Rear case

- This document cannot be used without Samsung’s Authorization -

Disassemble PBA from the Bracket

Disassemble Sub PBA from the Bracket

Detach with tweezers

- This document cannot be used without Samsung’s Authorization -

Disassemble Home key from the OCTA

Remove all remained substance

Detach Cu sheet from the OCTA

Detach and replace Cu sheet

Watch out LCD damage

- This document cannot be used without Samsung’s Authorization -

Disassemble Ear jack & Speaker from the Rear

Remove all remained substance

- This document cannot be used without Samsung’s Authorization -

Disassemble Motor from the Bracket

- This document cannot be used without Samsung’s Authorization -

- This document cannot be used without Samsung’s Authorization -

Tweezers Anti-static gloves Window Press JIG Window Press Pad

- This document cannot be used without Samsung’s Authorization -

Attach Cu sheet on the OCTA

- This document cannot be used without Samsung’s Authorization -

Assemble Home key on the OCTA

Remove vinyl Fold up FPCB

- This document cannot be used without Samsung’s Authorization -

Assemble Ear jack & Speaker on the Rear

Join on the 1 guide point

Press Speaker enough

- This document cannot be used without Samsung’s Authorization -

Assemble Motor on the Bracket