Lecture 1-Petroleum Oil Refinery Processes

PETROLEUM REFINERY
PROCESSES
PETROLEUM REFINERY
CHEE 2404: Industrial Chemistry 2

Distillation Unit in a Refinery

OUTLINE
1. Introduction
2. Physical Processes
3. Thermal Processes
4. Catalytic Processes
5. Conversion of Heavy Residues
6. Treatment of Refinery Gas Streams

INTRODUCTION
• Oil refining is a key activity in the CPI.
• Over 600 refineries worldwide have a total
annual capacity of more than 3500 x 106 tonnes.
• Goal of oil refining is twofold:
i. production of fuels for transportation, power
generation and heating; and
ii. production of raw materials for the CPI.
• Oil refineries are complex plants but are
relatively mature and highly integrated.

World-Crude Oil Demand and Supply
7
CHEE 2404: Industrial Chemistry
http://climateerinvest.blogspot.in/2016/01/oil-barring-global-depression-supply.html
Crude Oil
The majority of crude oil is alkanes, cycloalkanes (naphthenes), aromatics,
polycyclic aromatics, S-containing compounds, etc.
Gasoline: branched alkanes
Diesel: linear alkanes

Heavier crude contains more polycyclic aromatics
Lead to carboneceous deposits called “coke”

Some crudes contain a lot of sulfur, which leads to processing considerations.

Refining operations
Petroleum refining processes and operations can be separated into five basic
areas:
• Fractionation (distillation) Separation of crude into groups of HC
-Atmospheric distillation
- Vacuum distillation
• Conversion Processes change the size and/or structure of hydrocarbon

molecules. These processes include: :
Decomposition (dividing) by thermal and catalytic cracking;

Unification (combining) through alkylation and polymerization
Alteration (rearranging) with isomerization and catalytic reforming
• Treatment Processes to prepare hydrocarbon streams for additional

processing and to prepare finished products..

Refining operations
•Separation of aromatics and naphthenes
•Sweetening
•Solvent extraction
•Solvent dewaxing
[ Chemical or physical ]
• Formulating and Blending is the process of mixing and

combining hydrocarbon fractions, additives, and other
components to produce finished products with specific
performance properties.
• Other Refining Operations include: light-ends recovery;
sour-water stripping; solid waste, process-water and wastewater
treatment; cooling, storage and handling and product movement;
hydrogen production; acid and tail-gas treatment; and sulfur recovery.
Flow scheme of a modern refinery
Conversion Processes
Treatment Processes
Fractionation Formulating and Blending
Physical and chemical processes
Chemical
Physical
Thermal Catalytic
Distillation Visbreaking Hydrotreating
Solvent extraction Delayed coking Catalytic reforming
Propane deasphalting Flexicoking Catalytic cracking
Solvent dewaxing Hydrocracking
Blending Catalytic dewaxing
Alkylation
Polymerization
Isomerization

PHYSICAL PROCESSES
• Desalting/dehydration
• Crude distillation
• Propane deasphalting
• Solvent extraction and dewaxing
• Blending

Desalting/dehydration
• Crude oil often contains water, inorganic salts, suspended solids, and water-
soluble trace metals.
• Step 0 in the refining process is to remove these contaminants so as to reduce
corrosion, plugging, and fouling of equipment and to prevent poisoning
catalysts in processing units.
• The two most typical methods of crude-oil desalting are chemical and
electrostatic separation, and both use hot water as the extraction agent.
• In chemical desalting, water and chemical surfactant (demulsifiers) are added
to the crude, which is heated so that salts and other impurities dissolve or
attach to the water, then held in a tank to settle out.
• Electrical desalting is the application of high-voltage electrostatic charges to
concentrate suspended water globules in the bottom of the settling tank.
Surfactants are added only when the crude has a large amount of suspended
solids.
• A third (and rare) process filters hot crude using diatomaceous earth.
• The crude oil feedstock is heated to 65-180°C to reduce viscosity and
surface tension for easier mixing and separation of the water. The
temperature is limited by the vapor pressure of the crude-oil feedstock.
• In both methods other chemicals may be added. Ammonia is often
used to reduce corrosion. Caustic or acid may be added to adjust the
pH of the water wash.


Continuous distillation columns
Classified according to:
1. Nature of the feed that they are processing:
– binary column - feed contains only two components;
– multi-component column - feed contains more than two
components.
2. Number of product streams they have:
– multi-product column - column has more than two product
streams.
3. Where extra feed exits when used to help with the
separation:
– extractive distillation - where the extra feed appears in the
bottom product stream;
– azeotropic distillation - where the extra feed appears at the
top product stream.
4. Type of column internals:
– tray column - trays of various designs used to hold up the
liquid to provide better contact between vapour and liquid;
– packed column - packings are used to enhance vapour-
liquid contact.
Main Components of Distillation Columns
• A vertical shell where separation
of liquid components is done.
• Column internals e.g.trays/plates
and/or packings which are used to
enhance component separations.
• A reboiler to provide the
necessary vaporization for the
distillation process.
• A condenser to cool and condense
the vapour leaving the top of the
column.
• A reflux drum to hold the
condensed vapour from the top of
the column so that liquid (reflux)
can be recycled back to the
column.

Trays and plates
Bubble cap trays
A riser or chimney is
fitted over each hole, and
a cap covers the riser. The
cap is mounted with a
space to allow vapour to
rise through the chimney
and be directed downward
by the cap, finally
discharging through slots
in the cap, and bubbling
through the liquid on the
tray.

Trays and plates
Valve trays
Perforations are covered by caps
lifted by vapour, which creates a
flow area and directs the vapour
horizontally into the liquid.
Sieve trays
Sieve trays are simply metal
plates with holes in them. Vapour
passes straight upward through
the liquid on the plate. The
arrangement, number and size of
the holes are design parameters.

Liquid and vapour flows in a tray column

Liquid and vapour flows in a tray column
• Each tray has 2 conduits called
downcomers: one on each side.
Liquid falls by gravity through
the downcomers from one tray
to the tray below.
• A weir ensures there is always
some liquid (holdup) on the tray
and is designed such that the the
holdup is at a suitable height,
e.g. such that the bubble caps are
covered by liquid.
• Vapour flows up the column and
is forced to pass through the
liquid via the openings on each
tray. The area allowed for the
passage of vapour on each tray
is called the active tray area.
Packings
• Packings are passive devices designed to increase the interfacial area
for vapour-liquid contact.
• They do not cause excessive pressure-drop across a packed section,
which is important because a high pressure drop would mean that more
energy is required to drive the vapour up the distillation column.
• Packed columns are called continuous-contact columns while trayed
columns are called staged-contact columns because of the manner in
which vapour and liquid are contacted.

Basic operation
• The feed is introduced somewhere
near the middle of the column to a
tray known as the feed tray.
• The feed tray divides the column into
a top (enriching or rectification) and
a bottom (stripping) section.
• The feed flows down the column
where it is collected in the reboiler.
• Heat (usually as steam) is supplied to
the reboiler to generate vapour.
• The vapour from the reboiler is re-
introduced into the unit at the bottom
of the column.
• The liquid removed from the reboiler
is known as the bottoms product or
simply, bottoms.

Basic operation
• Vapour moves up the column, exits the top, and is cooled in a
condenser. The condensed liquid is stored in a holding vessel known
as the reflux drum. Some of this liquid is recycled back to the top of
the column and this is called the reflux. The condensed liquid that is
removed from the system is known as the distillate or top product.
• Thus, there are internal flows of vapour and liquid within the column
as well as external flows of feeds and product streams, into and out of
the column.

Crude distillation
• Step 1 in the refining process is the separation of crude oil into various
fractions by distillation in atmospheric and vacuum towers. The main
fractions or "cuts" obtained have specific boiling-point ranges and can
be classified in order of decreasing volatility into gases, light
distillates, middle distillates, gas oils, and residuum.
Atmospheric distillation
• The desalted crude feedstock is preheated using recovered process
heat. The feedstock then flows to a direct-fired crude charge heater
then into the vertical distillation column just above the bottom, at
pressures slightly above atmospheric and at temperatures ranging from
340-370°C (above these temperatures undesirable thermal cracking
may occur). All but the heaviest fractions flash into vapor.
• As the hot vapor rises in the tower, its temperature is reduced. Heavy
fuel oil or asphalt residue is taken from the bottom. At successively
higher points on the tower, the various major products including
lubricating oil, heating oil, kerosene, gasoline, and uncondensed gases
(which condense at lower temperatures) are drawn off.
Atmospheric distillation

Simple crude distillation

Vacuum distillation
• To further distill the residuum or topped crude from the atmospheric
tower without thermal cracking, reduced pressure is required.
• The process takes place in one or more vacuum distillation towers.
• The principles of vacuum distillation resemble those of fractional
distillation except that larger diameter columns are used to maintain
comparable vapor velocities at the reduced pressures. The internal
designs of some vacuum towers are different from atmospheric towers
in that random packing and demister pads are used instead of trays.
• A typical first-phase vacuum tower may produce gas oils, lubricating-
oil base stocks, and heavy residual for propane deasphalting.
• A second-phase tower operating at lower vacuum may distill surplus
residuum from the atmospheric tower, which is not used for lube-stock
processing, and surplus residuum from the first vacuum tower not used
for deasphalting.
• Vacuum towers are typically used to separate catalytic cracking
feedstock from surplus residuum.
Vacuum distillation

Modern crude distillation

Propane deasphalting
• Coke-forming tendencies of heavier distillation products
are reduced by removal of asphaltenic materials by solvent
extraction.
• Liquid propane is a good solvent (butane and pentane are
also commonly used).
• Deasphalting is based on solubility of hydrocarbons in
propane, i.e. the type of molecule rather than RMM as in
distillation.
• Vacuum residue is fed to a countercurrent deasphalting
tower. Alkanes dissolve in propane whereas asphaltenic
materials (aromatic compounds), ‘coke-precursors’ do not.
• Asphalt is sent for thermal processing.
Propane deasphalting

Solvent extraction and dewaxing
• Solvent treating is a widely used method of refining lubricating oils as
well as a host of other refinery stocks.
• Since distillation (fractionation) separates petroleum products into
groups only by their boiling-point ranges, impurities may remain.
These include organic compounds containing sulfur, nitrogen, and
oxygen; inorganic salts and dissolved metals; and soluble salts that
were present in the crude feedstock.
• In addition, kerosene and distillates may have trace amounts of
aromatics and naphthenes, and lubricating oil base-stocks may contain
wax.
• Solvent refining processes including solvent extraction and solvent
dewaxing usually remove these undesirables at intermediate refining
stages or just before sending the product to storage.

Solvent extraction
• The purpose of solvent extraction is to prevent corrosion, protect catalyst
in subsequent processes, and improve finished products by removing
unsaturated, aromatic hydrocarbons from lubricant and grease stocks.
• The solvent extraction process separates aromatics, naphthenes, and
impurities from the product stream by dissolving or precipitation. The
feedstock is first dried and then treated using a continuous countercurrent
solvent treatment operation.
• In one type of process, the feedstock is washed with a liquid in which the
substances to be removed are more soluble than in the desired resultant
product. In another process, selected solvents are added to cause
impurities to precipitate out of the product. In the adsorption process,
highly porous solid materials collect liquid molecules on their surfaces.
• The solvent is separated from the product stream by heating, evaporation,
or fractionation, and residual trace amounts are subsequently removed
from the raffinate by steam stripping or vacuum flashing.

Solvent extraction
• Electric precipitation may be used for separation of inorganic compounds.
• The solvent is regenerated for reused in the process.
• The most widely used extraction solvents are phenol, furfural, and cresylic
acid.
• Other solvents less frequently used are liquid sulfur dioxide, nitrobenzene,
and 2,2' dichloroethyl ether.
• The selection of specific processes and chemical agents depends on the
nature of the feedstock being treated, the contaminants present, and the
finished product requirements.

Aromatic solvent extraction unit

Solvent dewaxing
• Solvent dewaxing is used to remove wax from either distillate or residual
basestock at any stage in the refining process.
• There are several processes in use for solvent dewaxing, but all have the
same general steps, which are::
– mixing the feedstock with a solvent;
– precipitating the wax from the mixture by chilling; and
– recovering the solvent from the wax and dewaxed oil for recycling by
distillation and steam stripping.
• Usually two solvents are used: toluene, which dissolves the oil and
maintains fluidity at low temperatures, and methyl ethyl ketone (MEK),
which dissolves little wax at low temperatures and acts as a wax
precipitating agent.
• Other solvents sometimes used include benzene, methyl isobutyl ketone,
propane, petroleum naphtha, ethylene dichloride, methylene chloride, and
sulfur dioxide.
• In addition, there is a catalytic process used as an alternate to solvent
dewaxing.
Solvent dewaxing unit

Solvent dewaxing unit

Blending
• Blending is the physical mixture of a number of different liquid
hydrocarbons to produce a finished product with certain desired
characteristics.
• Products can be blended in-line through a manifold system, or batch
blended in tanks and vessels.
• In-line blending of gasoline, distillates, jet fuel, and kerosene is
accomplished by injecting proportionate amounts of each component
into the main stream where turbulence promotes thorough mixing.
• Additives including octane enhancers, anti-oxidants, anti-knock agents,
gum and rust inhibitors, detergents, etc. are added during and/or after
blending to provide specific properties not inherent in hydrocarbons.

THERMAL PROCESSES
When a hydrocarbon is heated to a sufficiently
high temperature thermal cracking occurs. This
is sometimes referred to as pyrolysis (especially
when coal is the feedstock). When steam is used
it is called steam cracking. We will examine
two thermal processes used in refineries.
• Visbreaking
• Delayed coking

Visbreaking
• Visbreaking is a mild form of thermal cracking that lowers the
viscosity of heavy crude-oil residues without affecting the
boiling point range.
• Residuum from the atmospheric distillation tower is heated
(425-510ºC) at atmospheric pressure and mildly cracked in a
heater.
• It is then quenched with cool gas oil to control over-cracking,
and flashed in a distillation tower.
• Visbreaking is used to reduce the pour point of waxy residues
and reduce the viscosity of residues used for blending with
lighter fuel oils. Middle distillates may also be produced,
depending on product demand.
• The thermally cracked residue tar, which accumulates in the
bottom of the fractionation tower, is vacuum-flashed in a
stripper and the distillate recycled.

Visbreaking

Visbreaking
• Alternatively, vacuum residue can be cracked. The severity of the

visbreaking depends upon temperature and reaction time (1-8 min).
• Usually < 10 wt% of gasoline and lighter products are produced.

Delayed Coking
• Coking is a severe method of thermal cracking used to upgrade heavy
residuals into lighter products or distillates.
• Coking produces straight-run gasoline (Coker naphtha) and various
middle-distillate fractions used as catalytic cracking feedstock.
• The process completely reduces hydrogen so that the residue is a form
of carbon called "coke."
• Three typical types of coke are obtained (sponge coke, honeycomb
coke, and needle coke) depending upon the reaction mechanism, time,
temperature, and the crude feedstock.
• In delayed coking the heated charge (typically residuum from
atmospheric distillation towers) is transferred to large coke drums
which provide the long residence time needed to allow the cracking
reactions to proceed to completion.

Sponge coke derived from a petroleum feedstock that shows abundant pore
structure. Note the flow texture in the coke cell walls.
http://mccoy.lib.siu.edu/projects/crelling2/atlas/PetroleumCoke/pettut.html

Typical needle coke derived from a petroleum feedstock. The parallel layers and
linear fractures are distinctive and provide slip planes to relieve stress in the coke .
http://mccoy.lib.siu.edu/projects/crelling2/atlas/PetroleumCoke/pettut.htm
l

Delayed Coking
PET COKE
54
Delayed Coking
• Heavy feedstock is fed to a fractionator.
• The bottoms of the fractionator are fed to coker drums via a furnace
where the hot material (440°-500°C ) is held approximately 24 hours
(delayed) at pressures of 2-5 bar, until it cracks into lighter products.
• Vapors from the drums are returned to a fractionator where gas,
naphtha, and gas oils are separated out. The heavier hydrocarbons
produced in the fractionator are recycled through the furnace.
• After the coke reaches a predetermined level in one drum, the flow is
diverted to another drum to maintain continuous operation.
• The full drum is steamed to strip out uncracked hydrocarbons, cooled
by water injection, and de-coked by mechanical or hydraulic methods.
• The coke is mechanically removed by an auger rising from the bottom
of the drum. Hydraulic decoking consists of fracturing the coke bed
with high-pressure water ejected from a rotating cutter.

Cracking
• Crude oil contains many large molecules. If these are to be used as
fuels or feedstock for the chemical industry then they have to be
cracked into smaller molecules.
• When hydrocarbons burn they are reacting with oxygen in the air. In
general, the smaller the molecule the better it will mix and then react
with the air.
Small molecules
Big molecules
Medium
molecules
Fuel gas Petrol

Naphtha Kerosine
Diesel Fuel Oil and bitumen
© Boardworks Ltd 2003
CRACKING
Cracking
Involves the breaking of C-C bonds in alkanes
Converts heavy fractions into higher value products
THERMAL proceeds via a free radical mechanism
CATALYTIC proceeds via a carbocation (carbonium ion) mechanism

Thermal Cracking
• High Pressure ... 7000 kPa

• High Temperature ... 400°C to 900°C
• Free Radical Mechanism
• Homolytic fission
• Produces mostly alkenes ... e.g. ethene for
making polymers and ethanol
• Produces Hydrogen ... used in the Haber
Process and in margarine manufacture
• Bonds can be broken anywhere in the molecule
by C-C bond fission or C-H bond fission

Catalytic Cracking
• Slight pressure
• High Temperature ... 450°C
• Zeolite catalyst
• Carbocation Mechanism
• Heterolytic fission
• Produces branched and cyclic alkanes, aromatic
hydrocarbons
• used for motor fuels
ZEOLITES are crystalline aluminosilicates; clay

like substances

Catalytic Cracking
• Large hydrocarbons are broken into smaller
molecules using heat and a catalyst.
• This process is known as catalytic cracking.
• The small molecules produced are then separated
by distillation.
Distillation
tower
pressure
Catalytic
Heat to cracker
Big Molecules
vaporise
Molecules
break up

Catalytic Cracking
• In the catalytic cracker long chain molecules are
‘cracked’. An example of such a reaction is:
H H H H H H H H Octane
H C C C C C C C C H
H H H H H H H H
Heat
hexane catalyst
pressure
H H H H H H H H ethene
H C C C C C C H + C C
H H
Ethene
Used as a H H H H H H is used
fuel to make
C8H18 C6H14 + C2H4 plastics

CATALYTIC PROCESSES
• Fluid Catalytic Cracking (FCC)

• Hydrotreating
• Hydrocracking
• Catalytic Reforming
• Alkylation

Catalytic Cracking
• Main incentive for catalytic cracking is the need to
increase gasoline production.
• Feedstocks are typically vacuum gas oil.
• Cracking is catalyzed by solid acids which promote the
rupture of C-C bonds. The crucial intermediates are
carbocations (+ve charged HC ions) formed by the action
of the acid sites on the catalyst.
• Besides C-C cleavage many other reactions occur:
- isomerization
- protonation and deprotonation
- alkylation
- polymerization
- cyclization and condensation

Catalytic Cracking
• Catalytic cracking comprises a complex network of
reactions, both intra-molecular and inter-molecular.
• The formation of coke is an essential feature of the
cracking process and this coke deactivates the catalyst.
• Catalytic cracking is one of the largest applications of
catalysts: worldwide cracking capacity exceeds 500
million t/a.
• Catalytic cracking was the first large-scale application of
fluidized beds which explains the name fluid catalytic
cracking (FCC).
• Nowadays entrained-flow reactors are used instead of
fluidized beds but the name FCC is still retained.
Fluid Catalytic Cracking Regenerator
Reactor
65
Fluid Catalytic Cracking


• Oil is cracked in the presence of a finely divided catalyst, which is
maintained in an aerated or fluidized state by the oil vapours.
• The fluid cracker consists of a catalyst section and a fractionating
section that operate together as an integrated processing unit.
• The catalyst section contains the reactor and regenerator, which, with
the standpipe and riser, form the catalyst circulation unit. The fluid
catalyst is continuously circulated between the reactor and the
regenerator using air, oil vapors, and steam as the conveying media.
• Preheated feed is mixed with hot, regenerated catalyst in the riser and
combined with a recycle stream, vapourized, and raised to reactor
temperature (485-540°C) by the hot catalyst.
• As the mixture travels up the riser, the charge is cracked at 0.7-2 bar.
• In modern FCC units, all cracking takes place in the riser and the
"reactor" merely serves as a holding vessel for the cyclones. Cracked
product is then charged to a fractionating column where it is separated
into fractions, and some of the heavy oil is recycled to the riser.
• Spent catalyst is regenerated to get rid of coke that collects on the
catalyst during the process.
• Spent catalyst flows through the catalyst stripper to the regenerator,
where most of the coke deposits burn off at the bottom where
preheated air and spent catalyst are mixed.
• Fresh catalyst is added and worn-out catalyst removed to optimize the
cracking process.

Hydrotreating
• Catalytic hydrotreating is a hydrogenation process used to remove
about 90% of contaminants such as nitrogen, sulfur, oxygen, and
metals from liquid petroleum fractions.
• If these contaminants are not removed from the petroleum fractions
they can have detrimental effects on equipment, catalysts, and the
quality of the finished product.
• Typically, hydrotreating is done prior to processes such as catalytic
reforming so that the catalyst is not contaminated by untreated
feedstock. Hydrotreating is also used prior to catalytic cracking to
reduce sulfur and improve product yields, and to upgrade middle-
distillate petroleum fractions into finished kerosene, diesel fuel, and
heating fuel oils.
• In addition, hydrotreating converts olefins and aromatics to saturated
compounds.

Catalytic Hydrodesulfurization Process
• Hydrotreating for sulfur removal is called hydrodesulfurization.
• In an industrial hydrodesulfurization unit, such as in a refinery, the
hydrodesulfurization reaction takes place in a fixed-bed reactor at
elevated temperatures ranging from 300 to 400 °C and
elevated pressures ranging from 30 to 130 atmospheres of absolute
pressure, typically in the presence of a catalyst consisting of
an alumina base impregnated
with cobalt and molybdenum (usually called a CoMo catalyst).
• Occasionally, a combination of nickel and molybdenum (called NiMo)
is used, in addition to the CoMo catalyst, for specific difficult-to-treat
feed stocks, such as those containing a high level of chemically bound
nitrogen.

• The liquid feed (at the bottom left in the diagram) is pumped up to the
required elevated pressure and is joined by a stream of hydrogen-rich
recycle gas. The resulting liquid-gas mixture is preheated by flowing
through a heat exchanger.
• The preheated feed then flows through a fired heater where the feed
mixture is totally vaporized and heated to the required elevated
temperature before entering the reactor and flowing through a fixed-
bed of catalyst where the hydrodesulfurization reaction takes place.
• The hot reaction products are partially cooled by flowing through the
heat exchanger where the reactor feed was preheated and then flows
through a water-cooled heat exchanger before it flows through the
pressure controller (PC) and undergoes a pressure reduction down to
about 3 to 5 atmospheres.
• The resulting mixture of liquid and gas enters the gas
separator vessel at about 35 °C and 3 to 5 atmospheres of absolute
pressure. CHEE 2404: Industrial Chemistry 72
• Most of the hydrogen-rich gas from the gas separator vessel is recycle
gas, which is routed through an amine contactor for removal of the
reaction product H2S that it contains.
• The H2S-free hydrogen-rich gas is then recycled back for reuse in the
reactor section. Any excess gas from the gas separator vessel joins
the sour gas from the stripping of the reaction product liquid.
• The liquid from the gas separator vessel is routed through
a reboiled stripper distillation tower. The bottoms product from the
stripper is the final desulfurized liquid product from
hydrodesulfurization unit.
• The overhead sour gas from the stripper contains
hydrogen, methane, ethane, hydrogen sulfide, propane, and, perhaps,
some butane and heavier components. That sour gas is sent to the
refinery's central gas processing plant for removal of the hydrogen
sulfide in the refinery's main amine gas treating unit and through a
series of distillation towers for recovery of propane, butane
and pentane or heavier CHEE
components. The
2404: Industrial residual hydrogen, methane,73
Chemistry
ethane, and some propane is used as refinery fuel gas.
Hydrotreating: flow scheme

Hydrotreating: trickle-bed reactor

Hydrotreating: trickle-bed reactor
Spent
CoMo catalyst

165 TPH Hydrodesulfurization (HDS) Unit
Other Hydrotreating Processes
• Hydrotreating also can be used to improve the quality of pyrolysis

gasoline (pygas), a by-product from the manufacture of ethylene.
• Traditionally, the outlet for pygas has been motor gasoline blending,
because of its high octane number. However, only small portions can
be blended untreated owing to the unacceptable odor, color, and gum-
forming tendencies of this material.
• The quality of pygas, which is high in diolefin content, can be
satisfactorily improved by hydrotreating, whereby conversion of
diolefins into mono-olefins provides an acceptable product for motor
gas blending.

Other Hydrotreating Processes
• Hydrotreating processes differ depending upon the feedstock available
and catalysts used.
• Hydrotreating can be used to improve the burning characteristics of
distillates such as kerosene. by converting aromatics into naphthenes,
which are cleaner-burning compounds.
• Lube-oil hydrotreating uses hydrogen to improve product quality. With
mild lube hydrotreating saturation of olefins and improvements in
color, odor, and acid nature of the oil are achieved. Operating
temperatures and pressures are usually below 315° C and 60 bar.
Severe lube hydrotreating (T ~ 315 - 400°C and hydrogen pressures up
to 205 bar) is capable of saturating aromatic rings, along with sulfur
and nitrogen removal, to impart specific properties not achieved at
mild conditions.

Hydrocracking
• Hydrocracking is a two-stage process combining catalytic cracking and
hydrogenation, wherein heavier feedstock is cracked in the presence of
hydrogen to produce more desirable products.
• The process employs high pressure, high temperature, a catalyst, and
hydrogen. Hydrocracking is used for feedstock that are difficult to
process by either catalytic cracking or reforming, since these feedstock
are characterized usually by a high polycyclic aromatic content and/or
high concentrations of the two principal catalyst poisons, sulfur and
nitrogen compounds.
• The process largely depends on the nature of the feedstock and the
relative rates of the two competing reactions, hydrogenation and
cracking. Heavy aromatic feedstock is converted into lighter products
under a wide range of very high pressures (70-140 bar) and fairly high
temperatures (400°-800°C), in the presence of hydrogen and special
catalysts.
Hydrocracking
• When the feedstock has a high paraffinic content, the primary function
of hydrogen is to prevent the formation of polycyclic aromatic
compounds.
• Another important role of hydrogen in the hydrocracking process is to
reduce tar formation and prevent buildup of coke on the catalyst.
• Hydrogenation also serves to convert sulfur and nitrogen compounds
present in the feedstock to hydrogen sulfide and ammonia.
• Hydrocracking produces relatively large amounts of isobutane for
alkylation feedstock and also performs isomerization for pour-point
control and smoke-point control, both of which are important in high-
quality jet fuel.

Hydrocracking
• Preheated feedstock is mixed with recycled hydrogen and sent to the

first-stage reactor, where catalysts convert sulfur and nitrogen
compounds to H2S and NH3. Limited hydrocracking also occurs.
• After the hydrocarbon leaves the first stage, it is cooled and liquefied
and run through a separator. The hydrogen is recycled to the feedstock.
• The liquid is charged to a fractionator.
• The fractionator bottoms are again mixed with a hydrogen stream and
charged to the second stage. Since this material has already been
subjected to some hydrogenation, cracking, and reforming in the first
stage, the operations of the second stage are more severe (higher
temperatures and pressures). Again, the second stage product is
separated from the hydrogen and charged to the fractionator.
Hydrocracking process configuration

Hydrocracking flow scheme

Catalytic Reforming
• Catalytic reforming is an important process used to convert low-octane
naphthas into high-octane gasoline blending components called
reformates (BTX).
• Reforming represents the total effect of numerous reactions such as
cracking, polymerization, dehydrogenation, and isomerization taking
place simultaneously.
• Depending on the properties of the naphtha feedstock (as measured by
the paraffin, olefin, naphthene, and aromatic content) and catalysts
used, reformates can be produced with very high concentrations of
benzene, toluene, xylene, (BTX) and other aromatics useful in gasoline
blending and petrochemical processing.
• Hydrogen, a significant by-product, is separated from the reformate for
recycling and use in other processes.

Catalytic Reforming
• A catalytic reformer comprises a reactor and product-recovery section.
• There is a feed preparation section comprising a combination of
hydrotreatment and distillation.
• Most processes use Pt as the active catalyst. Sometimes Pt is
combined with a second catalyst (bimetallic catalyst) such as rhenium
or another noble metal.
• There are many different commercial processes including platforming,
powerforming, ultraforming, and Thermofor catalytic reforming.
• Some reformers operate at low pressure (3-13 bar), others at high
pressures (up to 70 bar). Some systems continuously regenerate the
catalyst in other systems. One reactor at a time is taken off-stream for
catalyst regeneration, and some facilities regenerate all of the reactors
during turnarounds.

Catalytic Reforming
• In the platforming process, the first step is preparation of the naphtha
feed to remove impurities from the naphtha and reduce catalyst
degradation.
• The naphtha feedstock is then mixed with hydrogen, vaporized, and
passed through a series of alternating furnace and fixed-bed reactors
containing a platinum catalyst.
• The effluent from the last reactor is cooled and sent to a separator to
permit removal of the hydrogen-rich gas stream from the top of the
separator for recycling.
• The liquid product from the bottom of the separator is sent to a
fractionator called a stabilizer (butanizer). It makes a bottom product
called reformate; butanes and lighter go overhead and are sent to the
saturated gas plant.

Catalytic reforming scheme

Semi-regenerative catalytic reforming

Continuous regenerative reforming

Catalytic reforming reactors

Alkylation
• Alkylation combines low-molecular-weight olefins (primarily a
mixture of propylene and butylene) with isobutane in the presence of
a catalyst, either sulfuric acid or hydrofluoric acid.
• The product is called alkylate and is composed of a mixture of high-
octane, branched-chain paraffinic hydrocarbons.
• Alkylate is a premium blending stock because it has exceptional
antiknock properties and is clean burning. The octane number of the
alkylate depends mainly upon the kind of olefins used and upon
operating conditions.

Sulphuric acid alkylation process
• In cascade type sulfuric acid (H2SO4) alkylation units, the feedstock
(propylene, butylene, amylene, and fresh isobutane) enters the reactor
and contacts the concentrated sulfuric acid catalyst (in concentrations
of 85% to 95% for good operation and to minimize corrosion).
• The reactor is divided into zones, with olefins fed through distributors
to each zone, and the sulfuric acid and isobutanes flowing over baffles
from zone to zone.
• The reactor effluent is separated into hydrocarbon and acid phases
in a settler, and the acid is returned to the reactor. The hydrocarbon
phase is hot-water washed with caustic for pH control before being
successively depropanized, deisobutanized, and debutanized. The
alkylate obtained from the deisobutanizer can then go directly to
motor-fuel blending or be rerun to produce aviation-grade blending
stock. The isobutane is recycled to the feed.



Alkylation with H2SO4 in Stratco
contactor with autorefrigeration

CONVERSION OF HEAVY
RESIDUES
• Processing of light crude, even in a complex refinery with FCC,
hydrocracking etc. does not yield a satisfactory product distribution.
The amounts of fuel oil are too high.

CONVERSION OF HEAVY RESIDUES
• For heavy oil the situation is even worse with ~ 50% fuel oil being
produced even in a complex refinery.
• Fuel oil is worth < original crude. The value of the products
decreases in the order: gasoline> kerosene/gas oil > crude oil > fuel
oil.

There are several reasons for an increased incentive to convert

fuel oil into lighter products:
1. The demand for light products such as gasoline and automotive
diesel fuels continues to increase while market for heavy fuel oil
is declining.
2. Environmental restrictions become more important. Fuel oil
contains high amounts of S, N, and metals, so measures must be
taken to lower emissions.
3. With the exception of Western Europe, the quality of crude oil
shows a worsening trend. It becomes heavier with higher
amounts of hetero-atoms, so more extensive processing is
required to obtain the same amount and quality of products.

In principle there are two solutions for upgrading residual oils

and for obtaining a better product distribution. These are carbon
out and hydrogen in processes.
1. Examples of carbon rejection processes are the Flexicoking
process (Exxon) and the FCC process discussed earlier.
2. Examples of hydrogen addition processes are the LC-fining
process (Lummus) and the HYCON process (Shell).

Fluid Coking and Flexicoking
• Both FLUID COKINGTM and FLEXICOKINGTM use fluid bed
technology to thermally convert heavy oils such as vacuum
residue, atmospheric residue, tar sands bitumen, heavy whole
crudes, deasphalter bottoms or cat plant bottoms.
• FLEXICOKING goes one step further than FLUID COKING: in
addition to generating clean liquids, FLEXICOKING also
produces a low-BTU gas in one integrated processing step that
can virtually eliminate petroleum coke production.
• The advantages are: flexibility to handle a variety of feed types;
high reliability with the average service factor between 90 -95%;
large single train capacity provides an economy of scale that
lowers investment cost; able to process 65 kB/SD of 20 wt%
Conradson Carbon resid in a single reactor; time between
turnarounds routinely approaches two years; able to process very
heavy feed stocks such as deasphalter bottoms at high feed rates.
• Additional FLEXICOKING benefit: Integrated gasification of up
to 97% of gross coke production
The Fluid Coking Process
• The fluid coking residuum conversion process uses non-catalytic,
thermal chemistry to achieve high conversion levels with even
the heaviest refinery feedstocks.
• Since most of the sulfur, nitrogen, metals, and Conradson Carbon
Residue feed contaminants are rejected with the coke, the full-
range of lighter products can be feed for an FCC unit.
• Use as a single train reduces manpower requirements and avoids
process load swings and frequent thermal cycles that are typical
of batch processes such as delayed coking.
• The configurations available with fluid coking are: extinction
recycle, once-through, and once-through with hydroclones.

The Flexicoking Process
• Flexicoking is a thermal technology for converting heavy
feedstocks to higher margin liquids and producing, a low BTU
(i.e. a low energy content) gas, instead of coke.
• The conversion of coke to clean fuel gas maximizes refinery
yield of hydrocarbons.
• The carbon rejection process results in lower hydrogen
consumption than alternative hydrogen-addition systems.
• The low BTU gas is typically fed to a CO boiler for heat
recovery but can also be used in modified furnaces/boilers;
atmospheric or vacuum pipestill furnaces; reboilers; waste heat
boilers; power plants and steel mills; or as hydrogen plant fuel,
which can significantly reduce or eliminate purchases of
expensive natural gas.
• The small residual coke produced can be sold as boiler fuel for
generating electricity and steam or as burner fuel for cement
plants.

The Flexicoking Process

Catalytic hydrogenation of residues
• This is a “hydrogen-in” route.
• It serves two purposes: removal of Sulphur, Nitrogen and metal
compounds, and the production of light products.
• Reactions are similar to those occurring in hydrotreating and
hydrocracking of gas oils, but there are two important
differences.
• (1) Residues contain much higher amounts of sulphur, nitrogen
and polycyclic aromatic compounds; and
• (2) removal of metals, which are concentrated in the residual
fraction of the crude, means that operating conditions are more
severe and hydrogen consumption greater than for
hydroprocessing of gas oils.

Catalyst deactivation
• Deposition of metals causes catalyst deactivation.
• Basically all metals in the periodic table are present in crude oil
with the major ones being Ni and V.
• At the reaction conditions H2S is present, hence metal sulphides
are formed.
• The reaction scheme is complex but may be represented simply
as:
Ni-porphyrin + H2  NiS + hydrocarbons and
V-porphyrin + H2  V2S3 + hydrocarbons
• The catalyst is poisoned by this process because most of the
deposition occurs on the outer shell of the catalyst particles,
initially poisoning the active sites then causing pore plugging.

Reactors used for catalytic hydrogenation
• Three types of reactor are used: (1) fixed-bed reactors; (2) fluidized-
bed reactors (also called ebulliated-bed reactors); and (3) slurry
reactors.

The LC-fining process
• Developed by Lummus.
• Uses fluidized-bed reactors.

Processes with fixed-bed reactors
• Replacement of deactivated catalyst in a conventional fixed-bed reactor is not
possible during operation.
• Depending on the metal content of the feedstock various combinations can be
applied.

HYCON process

Catalyst rejuvenation
• Catalyst rejuvenation is achieved by removal of metal sulphides and
carbonaceous deposits (essentially by oxidation), and by extraction of the
metals.

Processes with slurry reactors
• Slurry processes for residue processing are normally designed
with the objective of maximizing residue conversion.
• Downstream reactors are then used to treat the liquid products
for S and N removal.
• Examples of the slurry process are the Veba Combi-Cracking
and CANMET process.
• Conversion of residual feed takes place in the liquid phase in a
slurry reactor.
• After separation the residue from the products they are further
hydro-treated in a fixed-bed reactor containing an HDS catalyst.
• A cheap, once-through catalyst is used which ends up in the
residue.

Veba Combi-Cracking process

TREATMENT OF REFINERY
GASES
• Removal of H2S from gases is usually performed by absorption in the
liquid phase.
• The concentrated H2S is frequently converted to elemental sulphur by
the “Claus” process (partial oxidation of H2S)
• In the Claus process 95-97% of the H2S is converted.
• H2S is often removed with solvents that can be regenerated, usually
alkanolamines: e.g. CH2(OH)CH2NH2 MEA (mono-ethanolamine).
• These amines are highly water soluble with low volatility and their
interaction with H2S is much faster than with CO2 so that the amount
of absorbed CO2 can be limited by selecting appropriate conditions.

Flow scheme for H2S removal by amine
absorption

Flow scheme of a typical Claus process

REFERENCES
Some great websites are:

• http://lorien.ncl.ac.uk/ming/distil/distil0.htm
• http://science.howstuffworks.com/oil-
refining.htm

Lecture 1-Petroleum Oil Refinery Processes

Uploaded by

Copyright:

Available Formats

Lecture 1-Petroleum Oil Refinery Processes

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Lecture 1-Petroleum Oil Refinery Processes

Uploaded by

Copyright:

Available Formats

PETROLEUM REFINERY

CHEE 2404: Industrial Chemistry 2

CHEE 2404: Industrial Chemistry 3

CHEE 2404: Industrial Chemistry 4

CHEE 2404: Industrial Chemistry 5

CHEE 2404: Industrial Chemistry 8

CHEE 2404: Industrial Chemistry 9

CHEE 2404: Industrial Chemistry 10

• Conversion Processes change the size and/or structure of hydrocarbon

Decomposition (dividing) by thermal and catalytic cracking;

• Treatment Processes to prepare hydrocarbon streams for additional

CHEE 2404: Industrial Chemistry 11

• Formulating and Blending is the process of mixing and

CHEE 2404: Industrial Chemistry 14

CHEE 2404: Industrial Chemistry 15

CHEE 2404: Industrial Chemistry 17

CHEE 2404: Industrial Chemistry 18

CHEE 2404: Industrial Chemistry 20

CHEE 2404: Industrial Chemistry 24

CHEE 2404: Industrial Chemistry 25

CHEE 2404: Industrial Chemistry 26

CHEE 2404: Industrial Chemistry 28

CHEE 2404: Industrial Chemistry 29

CHEE 2404: Industrial Chemistry 30

CHEE 2404: Industrial Chemistry 32

CHEE 2404: Industrial Chemistry 33

CHEE 2404: Industrial Chemistry 35

CHEE 2404: Industrial Chemistry 36

CHEE 2404: Industrial Chemistry 38

CHEE 2404: Industrial Chemistry 39

CHEE 2404: Industrial Chemistry 40

CHEE 2404: Industrial Chemistry 41

CHEE 2404: Industrial Chemistry 42

CHEE 2404: Industrial Chemistry 44

CHEE 2404: Industrial Chemistry 45

CHEE 2404: Industrial Chemistry 46

CHEE 2404: Industrial Chemistry 47

CHEE 2404: Industrial Chemistry 48

CHEE 2404: Industrial Chemistry 49

• Alternatively, vacuum residue can be cracked. The severity of the

CHEE 2404: Industrial Chemistry 50

CHEE 2404: Industrial Chemistry 51

CHEE 2404: Industrial Chemistry 52

CHEE 2404: Industrial Chemistry 53

CHEE 2404: Industrial Chemistry 55

Fuel gas Petrol

Involves the breaking of C-C bonds in alkanes

Converts heavy fractions into higher value products

THERMAL proceeds via a free radical mechanism

CATALYTIC proceeds via a carbocation (carbonium ion) mechanism

© Boardworks Ltd 2003

• High Pressure ... 7000 kPa

© Boardworks Ltd 2003

ZEOLITES are crystalline aluminosilicates; clay

© Boardworks Ltd 2003

© Boardworks Ltd 2003

© Boardworks Ltd 2003

• Fluid Catalytic Cracking (FCC)

CHEE 2404: Industrial Chemistry 62

CHEE 2404: Industrial Chemistry 63