Scribd
Upload
36 views27 pages

The Ptrms-4.0 (Deneb) : Remote Monitoring System

The document describes the PTRMS-4.0 remote monitoring system (also called Deneb), which acts as the master device to collect data from various slave devices connected via RS485 and send it to a server via GPRS. It collects data, critical alarms, status reports, and logical alarms from devices like digital I/O boards, RFID readers, energy meters, access control systems, battery monitors, and fuel sensors. The master can remotely configure slaves and settings via SMS. New devices just require adding a configuration file.

Uploaded by

simply_mail
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
36 views27 pages

The Ptrms-4.0 (Deneb) : Remote Monitoring System

The document describes the PTRMS-4.0 remote monitoring system (also called Deneb), which acts as the master device to collect data from various slave devices connected via RS485 and send it to a server via GPRS. It collects data, critical alarms, status reports, and logical alarms from devices like digital I/O boards, RFID readers, energy meters, access control systems, battery monitors, and fuel sensors. The master can remotely configure slaves and settings via SMS. New devices just require adding a configuration file.

Uploaded by

simply_mail
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 27

THE PTRMS-4.

0
(Deneb)

Remote Monitoring System


About The Product

• This version of the RMS is basically dedicated for


the collection of the data from every slaves
connected to it, i.e. it is now master device of the
whole setup.

• Its main function is to collect data from all of the


devices and send it on our server by the mean of
GPRS link.
About The Product
• It send us the messages so that we can have
information about some critical alarms even
when GPRS link is down.

• It also send us the report packets and the


packet which contents the status of logical
alarms like PP-Battery low, High Temperature,
Low Fuel, Top up, Drain Out.
About The Product
• It communicates with all of the devices on
RS485.
• It gives a command on the 485 bus which is
connected with every devices. The command
consists of a device ID on its initial byte and
according to that ID the respective device will
give its response.
Main Features :
• It provides SMS feature to us so that even in the
link is down we will have the current status of
the site.
• It gives us the feature of Local storage so that
every data is stored and safe in any case.
• We can configure all of the slaves connected with
DENEB remotely.
• We can configure some settings of DENEB with
the help of SMS also.
Main Features :
• To add or to Remove any device from the 485 bus is
now very simple. The only thing which is required is
that the new device must supports the MODBUS
protocol.
• Just by adding its configuration file which contents its
settings we can plug a new device.
• It sends the data of every device after a regular
interval. If due to any change in the status of any
device packet a new event packet is generated and
instantly transmitted on server.
Slaves Connected with The Master:
• Digital Input Output Board (DIO).
• RF-ID (ASM).
• AC Energy Meter.
• Access Control System (ibutton-ACS).
• DC Energy Meter.
• Battery Monitoring System (BMS).
• Fuel Sensor.
Connection Sequence of the slaves
1. DIO
7. FUEL
SENSOR

2. AMS

MASTER (DENEB) 3. AC ENERGY


6. BMS METER

4. ACCESS
5. DC ENERGY CONTROL
METER SYSTEM
Master’s (Deneb)Description :

RF Antenna Slot for SIM


connector
For MMC
Ethernet Card
Slot
USB Slot

THE DENEB FRONT VIEW


Master’s (Deneb) Description (Front):
• Connect Antenna cable properly at RF antenna
Connector.
• Insert SIM in SIM socket.
• The Ethernet slot is used to connect the Deneb
with our PC/Lap top.
• With USB slot we can attach the CDMA modem
or ant USB device which is supported by Deneb.
• In MMC slot Micro SD card is inserted.
Master’s (Deneb) Description :

RS-485 12 V
RS-232 Supply
Connector
Connector

BACK SIDE VIEW


Master’s Description (Back side) :
• There is phone jack a connector for 12V
power supply.
• There is a Red colored LED which indicates the
power ON state of the Deneb.
• The RS-485 connector is basically used as the
communication connector. All of the
communication wire finally terminates on this
DB-9 Male connector.
Slave’s Description 1. DIO
Power Connector

Connector of
Temperature sensor

16-
Digital
Inputs

4-Relay
Output

Connector for
Communication
DIO
• DB-9 Female connector is used to communicate the
DIO with Deneb. This output is given to a 232-485
converter which finally this o/p is connected to main
485-Bus .
• Its device ID is 52.
• This device gives the 24-digital alarms i/p and 8 digital
o/p. Also it senses the temperature and gives the
current room temperature reading.
• There is a bit of change in the hardware of the DIO.
Here we have to verify that the o/p of the Relay no. 1
must be N & NC instead of N & O.
2. AMS (RF-ID)
For communication

Tags Of
RF-ID
RF-ID (AMS)

• This device is basically consist of active tags


which transmits their data after every
configured time interval Its device ID is 55.

• With the help of this module we can assure


the presence of any device in which the tag is
attached.
3. AC Energy Meter :
AC Energy Meter :
• This device is used to measure mainly R Y B
voltages and EB Energy and DG Energy.
• Its device ID is 17.
4. Access Control System :

I-Button And its Reader


Access Control System :
• This device controls the access of a person in
the shelter. Until the i-Button is applied the
door does not opens.

• Its device ID is 51.


5. DC Energy Meter :
DC Energy Meter :

• This device is basically used to measure DC


voltage, DC Current and DC energy.

• Its device ID is 01.


6. Battery Monitoring System :
Battery Monitoring System :
• Its main function is to monitor the status of
the battery of the site.
• It gives us the Charging and discharging
current needed by battery.
• Its device ID is 65.
7. Fuel Sensor :
Fuel Sensor :
• It senses the level of fuel.

• It also communicates on RS485.

• Its Device ID is 49.


8. Logical Packet
• This packet consists of the data like Fuel Top-
up and Drain-out, Low PP Battery alarm, High
temperature alarm, Low fuel alarm.
• Whenever the parameters of this packet
changes this packet is transmitted on the
server.

You might also like