Scribd
Upload
82 views24 pages

Electronic Filters

This document describes an electronics lab experiment on electrical filters. The objectives are to learn about different filter types, their frequency response graphs, and create filters using circuit elements. Students will assemble simple low-pass, high-pass, and band-pass filters and measure their voltage output at various frequencies to generate graphs of gain vs. frequency. They will analyze the graphs to determine the filter type and cutoff frequencies. A final individual report is required that includes the graphs, filter determinations, and signed lab notes.

Uploaded by

prasad243243
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
82 views24 pages

Electronic Filters

This document describes an electronics lab experiment on electrical filters. The objectives are to learn about different filter types, their frequency response graphs, and create filters using circuit elements. Students will assemble simple low-pass, high-pass, and band-pass filters and measure their voltage output at various frequencies to generate graphs of gain vs. frequency. They will analyze the graphs to determine the filter type and cutoff frequencies. A final individual report is required that includes the graphs, filter determinations, and signed lab notes.

Uploaded by

prasad243243
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPT, PDF, TXT or read online on Scribd
You are on page 1/ 24

Laboratory 10:

Electronic Filters
Overview

Objectives
Background
Materials
Procedure
Report / Presentation
Closing
Objectives
Learn about electrical filters
Different types
Uses
What is the -3dB point?
Create filters and a crystal set radio using
multiple circuit elements
Identify filters based on generated graphs
Frequency Response Graph
 Gain (in dB)
 Ratio of output against input
 20*log (Vout/Vin)
 Always negative value
 -3dB Point
 3dB drop of signal power from highest point on gain
 Signal power is half of original value
 Cutoff Frequency (in Hz)
 Frequency at -3dB Point
Frequency Response Graph
 Plot of Gain versus Frequency of electrical signal
 Semi-logarithmic scale
 Linear Y-axis, logarithmic X-axis
Max Gain (dB)
Gain (dB)
(linear scale) Gain is 3 dB
lower than
the max
3 dB

Bandwidth
f (kHz)
Cutoff Frequency (log scale)

Gain vs. Frequency


What are Filters?
Eliminate unwanted frequencies
High-pass or low-pass
Favor desired frequencies
Band-pass
Bandwidth: frequency range filter allows to pass

Example
Radio tunes in to particular station
Basic Filter Types
•Low-Pass
• Low-Pass Filter
•High-Pass – Low frequencies pass

•Band-Pass

3dB Point:
-3dB
Cutoff Frequency:
1590 Hz
Bandwidth:
0 - 1590 Hz
Basic Filter Types
•Low-Pass
• High-Pass Filter
•High-Pass – High frequencies pass

•Band-Pass

3dB Point:
-3dB
Cutoff Frequency:
160 Hz
Bandwidth:
160 - ∞ Hz
Basic Filter Types
•Low-Pass
• Band-Pass Filter
•High-Pass – Limited frequency range passes

•Band-Pass

3dB Point: -3dB


Cutoff Frequencies:
400 and 600 Hz
Bandwidth:
400 - 600 Hz
Resonant Frequency
(High Response Point):
500 Hz
Electrical Terminology
•Terms

•Elements Voltage (V) [unit = V for Volts]


Potential difference in electrical energy
•Wiring

Current (I) [unit = A for Amperes]


Charge flow rate
Can be positive or negative
Electrical Terminology
Symbol
•Terms Resistor (R)
•Elements [unit = Ω for Ohms]
Resists flow of electrical current
•Wiring Dissipates electrical energy as heat
Often used to alter voltages in circuits
Characterized by Ohm’s Law: V = I*R
Not sensitive to frequency
Uses a poor conductor
Example: Carbon
Electrical Terminology
Symbol
•Terms
Capacitor (C)
•Elements [unit = F for Farads]
Stores potential energy (V)
•Wiring
Affected by voltage and frequency
A pair metal plates separated by
non-conductive material
Example: Air
Electrical charge accumulates on
plates
Electrical Terminology
•Terms
Inductor (L) Symbol

•Elements [unit = H for Henries]


Stores and delivers energy in a
•Wiring magnetic field
Magnetic fields affect the current of
a circuit
Effected by current and frequency
Is a coil of wire
Electrical Terminology
•Terms  Series
 Same current through
•Elements
all elements
•Wiring  Vin = VA + VB + VC

 Parallel
 Same voltage across
all branches
 Vin = VD = VE = VF + VG
Materials for Lab
Resistors
Brown, black, yellow = 100KΩ
Brown, black, green = 1MΩ
Capacitors
102 = 0.001 µF
10J = 10pF
Inductors
1mH
Materials for Lab (Cont’d)

Function generator
Coax cable
Plunger clips
Breadboard
PC
SignalExpress Oscilloscope VI
DAC Board
Procedure -Calibrate Function
Generator
Insert coaxial end of connecting cable into
50Ω output on function generator
Connect alligator clips
Red to pin 33 wire of DAC board
Black to pin 66 wire of DAC board
Set function generator range to 1 kHz
Set mode to Sine Wave (~)
Tune output frequency to 1kHz
Display must read 1.000 kHz
Procedure - Circuit 1
Connect the 100kΩ resistor and .001 µF
capacitor in series
Procedure - Circuit 2

Connect 0.001 µF capacitor to 1 MΩ


resistor in series
Procedure - Circuit 3
Assemble the circuit below
Procedure - Testing
1. Connect function generator to circuit
(function generator is VIN in schematics)
2. Connect DAC board to circuit as VOUT
3. Set function generator to 10 Hz
4. Record Vp-p reading on data view chart
• Appears below wave
5. Repeat steps 1-3 for frequencies of 20, 50,
100, 200, 500, 1000, 2000, 5000, 10000 Hz
Procedure – Data Analysis
For first two circuits, generate a graph
Plot of 20*log(Vout/Vin) vs. Frequency
Semi-log scale
Y-axis must be linear
X-axis must be log scale
Properly label each graph and all axes

TA must sign lab notes to verify data


Assignment: Report
 Individual Report (one report per student)
 Title page
 Discussion topics in the manual
 For first two circuits
 Include Excel tables and Gain vs. Frequency graphs
 Determine filter type
 Label each graph with determined filter type
 Have TA scan in signed lab notes
 OPTIONAL- Include photos of circuits and setup
Closing
TA will assign which circuit you start with
Have all original data signed by your TA
All team members must actively
participate in experiment
Submit all work electronically
Return all materials to your TA

You might also like