Electronic Devices and Circuits: Faculty: Mr. M Srinivas Reddy

ELECTRONIC DEVICES
AND CIRCUITS
Faculty:
Mr. M SRINIVAS REDDY
UNIT-I
• ELECTRON DYNAMICS AND CRO:

Motion of charged particles in electric and
magnetic fields. Simple problems involving
electric and magnetic fields only.
Electrostatic and magnetic focusing.
Principles of CRT, deflection sensitivity
(Electrostatic and magnetic deflection),
parallel and perpendicular electric and
magnetic fields
Deflection of Electrons in a
Uniform Electric Field
• Consider an electron beam directed between

two oppositely charged parallel plates as
shown below.
• With a constant potential difference between
the two deflecting plates, the trace is curved
+
towards the positive plate.
-
Deflection of Electrons in a Uniform
Electric Field
• The force acting on each electron in the
field is given by
eVP
F  eE 
d
where E = electric field strength,

Vp = p.d. between plates,
d = plate spacing.
Deflection of Electrons in a Uniform
Electric Field
• The vertical displacement y is given by
1 2 1 eV p 2
y  at  ( )t
2 2 md
1 eV p x 2
 ( ) 2
2 md v
This is the equation for a parabola.

Uniform Magnetic Field
• The force F acting on an electron in a
uniform magnetic field is given by
F  Bev
Since the magnetic force F is at right angles to

the velocity direction, the electron moves round
a circular path.
Uniform Magnetic Field
• The centripetal acceleration of the
electrons is
Bev
a
m
v 2 Bev
Hence a   which gives
r m
mv
r
eB
Cathode Ray Oscilloscope
(CRO)
• The structure of the cathode ray tube
Cathode Ray Oscilloscope
Controls
• Y-Gain
• Time Base
Y-Gain
• amplifies the Y-deflection
• small input voltages are amplified by

built-in amplifiers before applying to the
Y-plates.
• Y- Gain = 0.5 V/div

– 0.5 volt will cause a vertical deflection of 1
division
Time Base
• is a saw-tooth voltage applied internally
across the X-plates.
volts
time
Time Base
• controls the speed at which the spot
sweeps across the screen horizontally
from left to right.
volts Fly back
spot on right side
of screen
spot at centre
of screen 0 time
spot on left side

of screen
Time taken
for spot to
move across
the screen and
back
volts
spot on right side Fly back
of screen
spot at centre
of screen 0 time
spot on left side

of screen
Screen
Time Base
• it helps to display the actual waveform
of any a.c. applied across the Y-plates
• normally calibrated in
– s/cm
– ms/cm
– s/cm
• gives the time required for the spot to sweep 1
cm horizontally across the screen.
Time Base: How It Works
volts Fly back
spot on right side
of screen
B
spot at centre
of screen 0 time
spot on left side

A
of screen C
Time taken for spot to move
across the screen and back
Uses of c.r.o.
• Measure potential difference
– d.c.
– a.c.
• Display waveforms of alternating p.d.
• Measure short intervals of time, and
• Compare frequencies
Measuring d.c. Potential
Difference
• switch off the time-base
• a spot will be seen on the c.r.o. screen
• d.c. to be measured is applied to the Y-
plates
• spot will either deflected upwards or
downwards
• deflection of the spot is proportional to
the d.c. voltage applied
Measuring d.c. Potential
Difference
If the Y-gain control is set
y at 2 volts/division
And the vertical
deflection, y, is 1.5
Then d.c. voltage
= 1.5 x 2
= 3.0 V
Y-input
Measuring a.c. voltage
• switch off the time-base
• a spot will be seen on the c.r.o. screen
• a.c. to be measured is applied to the Y-plates
• spot will move up and down along the vertical
axis at the same frequency as the alternating
voltage
– spot moves to the top when the voltage increases to
its maximum (positive)
– spot moves to the bottom when the voltage
decreases to its lowest (negative)
• When the frequency is high
– the spot will move so fast that a vertical line is
seen on the screen
• Length of the vertical line gives the peak-
to-peak voltage (Vpp) applied to the Y-plate
• The peak voltage (Vp) is
= Vpp/2
Vpp
Y-input
Vp
Vp = Vpp/2
Vpp
C.R.O. as a Voltmeter
• it has nearly infinite resistance (between
the X- and Y-plates), therefore draws very
little current;
• it can be used to measure both d.c. and
a.c. voltages; and
• it has an immediate response.
Displaying Waveforms
• Set the time-base to a suitable frequency,
• Apply the input to the Y-plate
– a steady waveform of the input will be
displayed on the c.r.o.
Y-input
• When input voltage frequency is the same
as the time-base frequency
Input Voltage
c.r.o. screen
• When input voltage frequency is the twice
the time-base frequency
Input Voltage
c.r.o. screen
Measuring Short Time Intervals
• Set time-base to its lowest frequency
range
• Connect microphone to the Y-input
• Blow two short whistles into the
microphone
– two short pulses, at short interval apart will be
displayed on the c.r.o. screen
If the time-base is 10 ms/division

t divisions
and
if the separation between pulses
is t divisions
then
time interval is 10t ms
c.r.o. screen
Y-input
Lissajous’ Figures
• Lissajous’ figure can be displayed by
applying two a.c. signals simultaneously to
the X-plates and Y-plates of an
oscilloscope.
• As the frequency, amplitude and phase
difference are altered, different patterns
are seen on the screen of the CRO.
Lissajous’ Figures
Same amplitude but different frequencies

Electronic Devices and Circuits: Faculty: Mr. M Srinivas Reddy

Uploaded by

Copyright:

Available Formats

Electronic Devices and Circuits: Faculty: Mr. M Srinivas Reddy

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Electronic Devices and Circuits: Faculty: Mr. M Srinivas Reddy

Uploaded by

Copyright:

Available Formats

ELECTRONIC DEVICES

• ELECTRON DYNAMICS AND CRO:

• Consider an electron beam directed between

where E = electric field strength,

This is the equation for a parabola.

Since the magnetic force F is at right angles to

• amplifies the Y-deflection

• small input voltages are amplified by

• Y- Gain = 0.5 V/div

spot on left side

spot on left side

spot on left side

If the time-base is 10 ms/division

Same amplitude but different frequencies

You might also like