Communication Networks

Chapter 3
Types of Communication
Networks
 Traditional
 Traditional local area network (LAN)
 Traditional wide area network (WAN)
 Higher-speed
 High-speed local area network (LAN)
 Metropolitan area network (MAN)
 High-speed wide area network (WAN)
Speed and Distance of
Communications Networks
Characteristics of WANs
 Covers large geographical areas
 Circuits provided by a common carrier
 Consists of interconnected switching nodes
 Traditional WANs provide modest capacity
 64000 bps common
 Business subscribers using T-1 service – 1.544 Mbps common
 Higher-speed WANs use optical fiber and transmission
technique known as asynchronous transfer mode (ATM)
 10s and 100s of Mbps common
Characteristics of LANs
 Like WAN, LAN interconnects a variety of
devices and provides a means for
information exchange among them
 Traditional LANs
 Provide data rates of 1 to 20 Mbps
 High-speed LANS
 Provide data rates of 100 Mbps to 1 Gbps
Differences between LANs and
WANs
 Scope of a LAN is smaller
 LAN interconnects devices within a single
building or cluster of buildings
 LAN usually owned by organization that
owns the attached devices
 For WANs, most of network assets are not
owned by same organization
 Internal data rate of LAN is much greater
The Need for MANs
 Traditional point-to-point and switched network
techniques used in WANs are inadequate for
growing needs of organizations
 Need for high capacity and low costs over large
area
 MAN provides:
 Service to customers in metropolitan areas
 Required capacity
 Lower cost and greater efficiency than equivalent
service from telephone company
Switching Terms
 Switching Nodes:
 Intermediate switching device that moves data
 Not concerned with content of data
 Stations:
 End devices that wish to communicate
 Each station is connected to a switching node
 Communications Network:
 A collection of switching nodes
Switched Network
Observations of Figure 3.3
 Some nodes connect only to other nodes (e.g., 5
and 7)
 Some nodes connect to one or more stations
 Node-station links usually dedicated point-to-
point links
 Node-node links usually multiplexed links
 Frequency-division multiplexing (FDM)
 Time-division multiplexing (TDM)
 Not a direct link between every node pair
Techniques Used in Switched
Networks
 Circuit switching
 Dedicated communications path between two
stations
 E.g., public telephone network
 Packet switching
 Message is broken into a series of packets
 Each node determines next leg of transmission
for each packet
Phases of Circuit Switching
 Circuit establishment
 An end to end circuit is established through switching
nodes
 Information Transfer
 Information transmitted through the network
 Data may be analog voice, digitized voice, or binary
data
 Circuit disconnect
 Circuit is terminated
 Each node deallocates dedicated resources
Characteristics of Circuit
Switching
 Can be inefficient
 Channel capacity dedicated for duration of connection
 Utilization not 100%
 Delay prior to signal transfer for establishment
 Once established, network is transparent to users
 Information transmitted at fixed data rate with
only propagation delay
Components of Public
Telecommunications Network
 Subscribers - devices that attach to the network;
mostly telephones
 Subscriber line - link between subscriber and
network
 Also called subscriber loop or local loop
 Exchanges - switching centers in the network
 A switching centers that support subscribers is an end
office
 Trunks - branches between exchanges
How Packet Switching Works
 Data is transmitted in blocks, called packets
 Before sending, the message is broken into
a series of packets
 Typical packet length is 1000 octets (bytes)
 Packets consists of a portion of data plus a
packet header that includes control information
 At each node en route, packet is received,
stored briefly and passed to the next node
Packet Switching
Packet Switching
Packet Switching Advantages
 Line efficiency is greater
 Many packets over time can dynamically share the same node
to node link
 Packet-switching networks can carry out data-rate
conversion
 Two stations with different data rates can exchange
information
 Unlike circuit-switching networks that block calls when
traffic is heavy, packet-switching still accepts packets,
but with increased delivery delay
 Priorities can be used
Disadvantages of Packet
Switching
 Each packet switching node introduces a delay
 Overall packet delay can vary substantially
 This is referred to as jitter
 Caused by differing packet sizes, routes taken and
varying delay in the switches
 Each packet requires overhead information
 Includes destination and sequencing information
 Reduces communication capacity
 More processing required at each node
Packet Switching Networks -
Datagram
 Each packet treated independently, without
reference to previous packets
 Each node chooses next node on packet’s path
 Packets don’t necessarily follow same route and
may arrive out of sequence
 Exit node restores packets to original order
 Responsibility of exit node or destination to detect
loss of packet and how to recover
Packet Switching Networks –
Datagram
 Advantages:
 Call setup phase is avoided
 Because it’s more primitive, it’s more flexible
 Datagram delivery is more reliable
Packet Switching Networks –
Virtual Circuit
 Preplanned route established before packets sent
 All packets between source and destination follow
this route
 Routing decision not required by nodes for each
packet
 Emulates a circuit in a circuit switching network
but is not a dedicated path
 Packets still buffered at each node and queued for
output over a line
Packet Switching Networks –
Virtual Circuit
 Advantages:
 Packets arrive in original order
 Packets arrive correctly
 Packets transmitted more rapidly without
routing decisions made at each node
Effect of Packet Size on
Transmission
Effect of Packet Size on
Transmission
 Breaking up packets decreases transmission time
because transmission is allowed to overlap
 Figure 3.9a
 Entire message (40 octets) + header information (3
octets) sent at once
 Transmission time: 129 octet-times
 Figure 3.9b
 Message broken into 2 packets (20 octets) + header (3
octets)
 Transmission time: 92 octet-times
Effect of Packet Size on
Transmission
 Figure 3.9c
 Message broken into 5 packets (8 octets) + header (3
octets)
 Transmission time: 77 octet-times
 Figure 3.9d
 Making the packets too small, transmission time starts
increases
 Each packet requires a fixed header; the more packets,
the more headers
Asynchronous Transfer Mode
(ATM)
 Also known as cell relay
 Operates at high data rates
 Resembles packet switching
 Involves transfer of data in discrete chunks, like packet
switching
 Allows multiple logical connections to be multiplexed
over a single physical interface
 Minimal error and flow control capabilities reduces
overhead processing and size
 Fixed-size cells simplify processing at ATM nodes
ATM Terminology
 Virtual channel connection (VCC)
 Logical connection in ATM
 Basic unit of switching in ATM network
 Analogous to a virtual circuit in packet switching
networks
 Exchanges variable-rate, full-duplex flow of fixed-size
cells
 Virtual path connection (VPC)
 Bundle of VCCs that have the same end points
Advantages of Virtual Paths
 Simplified network architecture
 Increased network performance and
reliability
 Reduced processing and short connection
setup time
 Enhanced network services
Call Establishment
Virtual Channel Connection Uses
 Between end users
 Can carry end-to-end user data or control
signaling between two users
 Between an end user and a network entity
 Used for user-to-network control signaling
 Between two network entities
 Used for network traffic management and
routing functions
Virtual Path/Virtual Channel
Characteristics
 Quality of service
 Specified by parameters such as cell loss ratio and cell
delay variation
 Switched and semipermanent virtual channel
connections
 Cell sequence integrity
 Traffic parameter negotiation and usage
monitoring
 Virtual channel identifier restriction within a VPC
ATM Cell Header Format
 Generic flow control (GFC) – 4 bits, used only in
user-network interface
 Used to alleviate short-term overload conditions in
network
 Virtual path identifier (VPI) – 8 bits at the user-
network interface, 12 bits at network-network
interface
 Routing field
 Virtual channel identifier (VCI) – 8 bits
 Used for routing to and from end user
ATM Cell Header Format
 Payload type (PT) – 3 bits
 Indicates type of information in information
field
 Cell loss priority (CLP) – 1 bit
 Provides guidance to network in the event of
congestion
 Header error control (HEC) – 8 bit
 Error code
ATM Service Categories
 Real-time service
 Constant bit rate (CBR)
 Real-time variable bit rate (rt-VBR)
 Non-real-time service
 Non-real-time variable bit rate (nrt-VBR)
 Available bit rate (ABR)
 Unspecified bit rate (UBR)
Examples of CBR Applications
 Videoconferencing
 Interactive audio (e.g., telephony)
 Audio/video distribution (e.g., television,
distance learning, pay-per-view)
 Audio/video retrieval (e.g., video-on-
demand, audio library)
Examples of UBR applications
 Text/data/image transfer, messaging,
distribution, retrieval
 Remote terminal (e.g., telecommuting)