Scribd
Upload
128 views10 pages

Literature Survey - Problem Statement - Objective - Components & Specifications - Comparison - KTP - Project Outcome - Budget

This document outlines the specifications and components for a 3D printer project. It includes sections on the printer body, hardware, electronics, IOT components, and estimated budget. The key components are NEMA 17 stepper motors, an Arduino Mega 2560, Ramps 1.4 controller board, heated print bed, extruder, and assorted sensors. The total estimated budget for the project is Rs. 32,380.

Uploaded by

Abrar Ahmed
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
128 views10 pages

Literature Survey - Problem Statement - Objective - Components & Specifications - Comparison - KTP - Project Outcome - Budget

This document outlines the specifications and components for a 3D printer project. It includes sections on the printer body, hardware, electronics, IOT components, and estimated budget. The key components are NEMA 17 stepper motors, an Arduino Mega 2560, Ramps 1.4 controller board, heated print bed, extruder, and assorted sensors. The total estimated budget for the project is Rs. 32,380.

Uploaded by

Abrar Ahmed
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PPTX, PDF, TXT or read online on Scribd
You are on page 1/ 10

Contents

Literature survey
Problem statement
Objective
Components & Specifications
Comparison
KTP
Project outcome
Budget
COMPONENTS & SPECIFICATIONS
NEMA 17 Stepper motors
Specifications -
Step Angle : 1.8 deg
Step Angle Accuracy : +/- 5%
Temprature Rise : 80 deg C Max
Current A - 1.5
A4988 Stepper Motor Driver
Specifications:-
Minimum operating voltage : 8 v
Maximum operating voltage : 35 v
Maximum operatingcurrent : 2A
Minimum logic voltage : 3v
Maximum logic voltage : 5.5 V
Microstep resolutions: Full, 1/2, 1/4,
1/8,1/16
Arduino Mega 2560
Specifications:-
Operating Voltage:- 3.3 v- 5v
Maximum current rating:- 50mA
It has 54 digital input/output pins
16 analog inputs
16 MHz crystal oscillator

Ramps 1.4
Specification:-
Supply Voltage : 12 V
Fused at 5A for additional safety
Heated bed control with additional 11A
fuse
2 stepper motor for Z axis in parallel.
Heatbed
Specifications:-
Voltage: 12V / 24V
Power: 120W
Size: 25x25 cm
Process: aluminum plate
180 degree Celsius max. temperature

Extruder
Specifications:-
Filament size: 1.75mm
Nozzle diameter: 0.4mm
12V 40W Heater
Comparison
SPECIFICATIONS MARKET 3DP SMART 3DP
Printing Size 210 mmx210 mm x210 250mm x250mmx 250mm
mm
Run Through Memory card, USB Internet
operated
Printing Tech Fused Deposition Fused Deposition
Modeling Modeling
Material Used PLA PLA
Feedback - Via IOT
Project outcomes
ESTIMATED BUDGET
Body Of 3D Printer:-
Aluminum channel for frame 10ft 4000
4mm Glass plate 100*1 100
M8 threaded rod 170*2 340
8mm smooth rods 1meter*10*200 2000
Angle brackets (As required) 500
LM8UU bearings 100*15 1500
Heated Printer Bed 1450*1 1450
Acrylic Sheet 250*1 250
TOTAL 10,140
Hardware:-

Stepper Motors 750*5 3750


Extruder 800*1 800
Endstops 50*3 150
MK8 Extruder block 630*1 630
GT2 Pulley 120* 4 480
GT2 Timing belt (6mm) 5 Meters 300
TOTAL 6,110

Electronics of the 3DP


Arduino MEGA 2560 1600*1 1600
RAMPS 1.4 shield 860*1 860
Stepper motor driver 235*5 1,175
LCD controller for 890*1 890
RAMPS
Memory Card 410*1 410
Relay 575*1 575
TOTAL 5,510
IOT Components :-
ESP8266 WI-FI module 400*1 400
Webcam 950*1 950
Wi-Fi router 1000*1 1000
Temperature Sensor 270*1 270
Weighing Sensor 500*1 500
TOTAL 3,120

Other expenses:-
SMPS Power Supply unit 900*1 900
Connecting Wires (As required) 200
PCB 200*1 200
Stationery 1000
Filament for printing ( PLA 1Kg * 4 units 5200
1.75mm)
TOTAL 7,500
Overall estimate:-
Body of the 3DP 10,140
Hardware components 6,110
Electronics of the 3DP 5,510
IOT components 3,120
Other Expenses 7,500

TOTAL 32,380/-

You might also like