CH1 Introduction

Lecture 1 : Introduction
Dr. Fath Elrahman Ismael Khalifa Ahmed

Sudan University of Science and Technology
Faculty of Engineering
School of Electronics
May / 2013 Department of Communications 1
Fiber optics has been merely a system for piping light
around corners and into inaccessible places so as to
allow the hidden to be seen. But now, fiber optics has
evolved into a system of significantly greater importance
and use.
Throughout the world it is now being used to transmit
voice, video, and data signals by light waves over
flexible hair-thin threads of glass or plastics.
Its advantages in such use, as compared to conventional
coaxial cable or twisted wire pairs, are fantastic.
As a result, light-wave communication systems or fiber
optics communication systems are one of the important
feature for today's communications.
3
Submarine Cables in Continental
(North East Asia)
4
5
Figure 1 : Fiber Optic Cable
Year Wavelength Bit rate Repeater
span
First generation 1978 850 nm 50-100
10-km
Mb/s
Second 1985 1300 nm 1-2 Gb/s 40-50 km
generation
Third generation -- 1550 nm > 2.5 Gb/s 100-km
1550 nm lowest loss but higher dispersion than 1300 nm.

DSF developed to have low loss and low dispersion at
1550 nm.
INSPIRING CREATIVE AND INNOVATIVE MINDS

At present the minimum attenuation for glass
fibers is reported to be 0.16 dB/km. There are
1500 nm systems operating with repeater spacing
of 150km.
Alcatel has un-repeatered systems of 2.5 Gb/s and
622 Mb/s spanning distance of 511 km and 531 km
respectively.
WDM systems operating at 1.28 Tbit/s (128
wavelengths at 10.7 Gbit/s each) is possible today
(Lucent Technology).

An optical fiber communication system is similar
in basic concept to any type of communication
systems.
Figure 1.1 shows a block diagram of a general

optical fiber communication system.
Figure 1.1
Information source provides electrical signal to the
transmitter comprising of an electrical stage which drives
an optical source to modulate the light wave carrier.
The optical source which convert electrical to optical

signal may be either a semiconductor injection laser diode
(ILD) or light emitting diode (LED).
Transmission medium consists of an optical fiber cable

and the receiver consists of an optical detector.
Photodiodes (p-n, p-i-n, or avalanche) are utilized for the
detection of the optical signal or the optical to electrical
conversion.
At present the signal processing is usually performed

electrically.
Figure 1.2

Input digital signal from information source is
suitably encoded for optical transmission.
Laser drive circuit directly modulates the intensity
of the semiconductor laser with the encoded
digital signal.
A digital optical signal is launched into the optical
fiber cable.
The avalanche photodiode detector (APD) is
followed by a front-end amplifier to provide gain,
linear signal processing and noise bandwidth
reduction.
The signal obtained is then decoded to give the
original digital information.
Enormous potential bandwidth
The optical carrier frequency in the range 1013 to 1016 Hz
yields a far greater potential transmission bandwidth than
metallic cable systems (i.e. coaxial cable bandwidth up to
around 500 MHz) or even millimeter wave radio systems (i.e
systems currently operating with modulation bandwidths of
700 MHz).
Potential BW:50 Tbit/s

Immunity to interference and crosstalk
Optical fibers are free from electromagnetic interference

(EMI) and radio frequency interference (RFI). Hence the
operation of an optical fiber communication system is
unaffected by transmission through an electrically noisy
environment and the fiber cable requires no shielding from
EMI.
The fiber cable is also not susceptible to lightning strikes
if used overhead rather than underground.
Moreover, it is fairly easy to ensure that there is no
optical interference between fibers and hence, unlike
communication using electrical conductors, crosstalk is
negligible, even when many fibers are cabled together.

Small size and weight
Optical fibers have very small diameters which are often no

greater than the diameter of a human hair. Hence, even when
such fibers are covered with protective coatings they are far
smaller and much lighter than corresponding copper cables.
This is a tremendous boom towards the alleviation of duct
congestion in cities, as well as allowing for an expansion of
signal transmission within mobiles such as aircraft, satellites
and even ships.
RG-19/U 22.6 dB/km at 100 MHz 1110 kg/km
Silica Fiber 5 dB/km 6 kg/km

Electrical Isolation
Optical fibers which are fabricated from glass or polymer

are electrical insulators and therefore, unlike their metallic
counterparts, they do not exhibit earth loop and interface
problems. Furthermore, this property makes optical fiber
transmission ideally suited for communication in electrically
hazardous environments as the fibers create no arcing or
spark hazard at abrasions or short circuits.

Signal security
The light from optical fibers does not radiate significantly
and therefore they provide a high degree of signal security.
Unlike copper cables, a transmitted optical signal cannot be
obtained from a fiber in a non-invasive manner (i.e.
without drawing optical power from the fiber). Therefore,
in theory, any attempt to acquire a message signal
transmitted optically may be detected. This feature is
obviously attractive for military, banking and general data
transmission (i.e. computer network) applications.

Low transmission loss
The development of optical fibers has resulted in the
production of optical fiber cables which exhibit very low
attenuation or transmission loss in comparison with the best
copper conductors. Fibers have been fabricated with losses as
low as 0.2 dB km-1 .
It facilitates the implementation of communication links with
extremely wide repeater spacing (long transmission distances
without intermediate electronics). thus reducing both system
cost and complexity.
Silica Fiber 100 MHz 4 dB/km
RG-19/U 500 MHz 14 dB/km

Ruggedness and flexibility
Although protective coatings are essential, optical fibers
may be manufactured with very high tensile strengths.
Perhaps surprisingly for a glassy substance, the fibers may
also be bent to quite small radius or twisted without
damage. Furthermore, cable structures have been
developed which have proved flexible, compact and
extremely rugged. These optical fiber cables are generally
superior in terms of storage, transportation, handling and
installation than corresponding copper cables whilst
exhibiting at least comparable strength and durability.
System reliability and ease of maintenance
These features primarily stem from the low loss property

of optical fiber cables which reduces the requirement for
intermediate repeaters or line amplifiers to boost the
transmitted signal strength. Hence with fewer repeaters,
system reliability is generally enhanced in comparison
with conventional electrical conductor systems.
Furthermore, the reliability of the optical components is
no longer a problem with predicted lifetimes of 20-30
years now quite common. Both these factors also tend
to reduce maintenance time and costs.
Potential low cost
The glass which generally provides the optical fiber
transmission medium is made from sand-not a scarce
resource. So, in comparison with copper conductors,
optical fibers offer the potential for low cost line
communication. Overall system cost when utilizing optical
system optical system are substantially less than those for
equivalent electrical line systems because of the low loss
and wideband properties of optical transmission.

Voice
1. Telephone trunk for high data
inter-office
inter-city
transoceanic
2. Subscriber service
fiber-to-the home (FTTH)
broadband services
(multimedia, video, etc. )

Video
1. Broadcast Television
live events
TV mini cameras
2. CATV
source-to-headend trunk lines
distributions
subscriber taps
3. Surveillance
4. Remote monitoring
5. Fiber-guided missile
6. Fiber-to-the home

Data
1. Computers
CPU to peripherals
CPU to CPU
2. Interoffice data links
3. Local Area Network (LAN)
4. Fiber-to-the home
5. Aircraft and ship wiring - reduced weight
6. Satellite ground stations

Sensors
1. Gyroscope
2. Hydrophone-acoustic measurements in water
3. Position
4. Temperature
5. Electric and Magnetic Fields
6. Medical

CH1 Introduction

Uploaded by

Copyright:

Available Formats

CH1 Introduction

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

CH1 Introduction

Uploaded by

Copyright:

Available Formats

Lecture 1 : Introduction

Dr. Fath Elrahman Ismael Khalifa Ahmed

1550 nm lowest loss but higher dispersion than 1300 nm.

INSPIRING CREATIVE AND INNOVATIVE MINDS

INSPIRING CREATIVE AND INNOVATIVE MINDS

Figure 1.1 shows a block diagram of a general

The optical source which convert electrical to optical

Transmission medium consists of an optical fiber cable

At present the signal processing is usually performed

INSPIRING CREATIVE AND INNOVATIVE MINDS

Potential BW:50 Tbit/s

INSPIRING CREATIVE AND INNOVATIVE MINDS

Optical fibers are free from electromagnetic interference

INSPIRING CREATIVE AND INNOVATIVE MINDS

Optical fibers have very small diameters which are often no

INSPIRING CREATIVE AND INNOVATIVE MINDS

Optical fibers which are fabricated from glass or polymer

INSPIRING CREATIVE AND INNOVATIVE MINDS

INSPIRING CREATIVE AND INNOVATIVE MINDS

INSPIRING CREATIVE AND INNOVATIVE MINDS

These features primarily stem from the low loss property

INSPIRING CREATIVE AND INNOVATIVE MINDS

INSPIRING CREATIVE AND INNOVATIVE MINDS

INSPIRING CREATIVE AND INNOVATIVE MINDS

INSPIRING CREATIVE AND INNOVATIVE MINDS

INSPIRING CREATIVE AND INNOVATIVE MINDS

You might also like