Lecture 1 Introduction Review of Classical Control

Advanced Control Systems (ACS)
Lecture-1
Introduction to Subject
&
Review of Basic Concepts of Classical control
Dr. Imtiaz Hussain

email: [email protected]
URL :http://imtiazhussainkalwar.weebly.com/
Course Outline
Review of basic concepts of classical control
State Space representation
Design of Compensators
Design of Proportional
Proportional plus Integral
Proportional Integral and Derivative (PID) controllers
Pole Placement Design
Design of Estimators
Linear Quadratic Gaussian (LQG) controllers
Linearization of non-linear systems
Design of non-linear systems
Analysis and Design of multivariable systems
Analysis and Design of Adaptive Control Systems
Recommended Books
1. Burns R. Advanced Control Engineering, Butterworth

Heinemann, Latest edition.
2. Mutanmbara A.G.O.; Design and analysis of Control
Systems, Taylor and Francis, Latest Edition
3. Modern Control Engineering, (5th Edition)
By: Katsuhiko Ogata.
4. Control Systems Engineering, (6th Edition)
By: Norman S. Nise
What is Control System?
A system Controlling the operation of another
system.
A system that can regulate itself and another
system.
A control System is a device, or set of devices
to manage, command, direct or regulate the
behaviour of other device(s) or system(s).
Types of Control System
Natural Control System
Universe
Human Body
Manmade Control System
Vehicles
Aeroplanes
Manual Control Systems
Room Temperature regulation Via Electric Fan
Water Level Control
Automatic Control System

Room Temperature regulation Via A.C
Human Body Temperature Control
Open-Loop Control Systems
Open-Loop Control Systems utilize a controller or control actuator to
obtain the desired response.
Output has no effect on the control action.
In other words output is neither measured nor fed back.
Input Output
Controller Process
Examples:- Washing Machine, Toaster, Electric Fan

Open-Loop Control Systems
Since in open loop control systems reference input is not

compared with measured output, for each reference input there
is fixed operating condition.
Therefore, the accuracy of the system depends on calibration.
The performance of open loop system is severely affected by the

presence of disturbances, or variation in operating/
environmental conditions.
Closed-Loop Control Systems
Closed-Loop Control Systems utilizes feedback to compare the actual

output to the desired output response.
Input Output
Comparator Controller Process
Measurement
Examples:- Refrigerator, Iron

Multivariable Control System
Temp Outputs
Humidity Comparator Controller Process
Pressure
Measurements
Feedback Control System
A system that maintains a prescribed relationship between the output

and some reference input by comparing them and using the difference
(i.e. error) as a means of control is called a feedback control system.
Input + error Output

Controller Process
-
Feedback
Feedback can be positive or negative.

Servo System
A Servo System (or servomechanism) is a feedback control system in

which the output is some mechanical position, velocity or acceleration.
Antenna Positioning System Modular Servo System (MS150)

Linear Vs Nonlinear Control System
A Control System in which output varies linearly with the input is called a
linear control system.
u(t) Process y(t)
y(t ) 2u(t ) 1 y(t ) 3u(t ) 5

y=3*u(t)+5
y=-2*u(t)+1
35
5
30
0
25
-5
y(t)
y(t)
20
-10
15
-15
10
-20 5
0 2 4 6 8 10 0 2 4 6 8 10
u(t)
u(t)
When the input and output has nonlinear relationship the system is said
to be nonlinear.
Adhesion Characteristics of Road
0.4
Adhesion Coefficient
0.3
0.2
0.1
0
0 0.02 0.04 0.06 0.08
Creep
Linear control System Does not
exist in practice. Adhesion Characteristics of Road
0.4
Linear control systems are
Adhesion Coefficient
idealized models fabricated by
0.3
the analyst purely for the
simplicity of analysis and design. 0.2
When the magnitude of signals 0.1

in a control system are limited to
range in which system 0
0 0.02 0.04 0.06 0.08
components exhibit linear Creep
characteristics the system is
essentially linear.
Temperature control of petroleum product in a distillation column.
Temperature
500C
Valve Position
0% 25% 100%
% Open
Time invariant vs Time variant
When the characteristics of the system do not depend upon time

itself then the system is said to time invariant control system.
y(t ) 2u(t ) 1
Time varying control system is a system in which one or more

parameters vary with time.
y(t ) 2u(t ) 3t
Lumped parameter vs Distributed Parameter
Control system that can be described by ordinary differential equations

are lumped-parameter control systems.
d 2x dx
M C kx
dt 2 dt
Whereas the distributed parameter control systems are described by
partial differential equations.
x x 2x
f1 f2 g 2
dy dz dz
Continuous Data Vs Discrete Data System
In continuous data control system all system variables are function of a

continuous time t.
x(t)
A discrete time control system involves one or more variables that are
known only at discrete time intervals.
X[n]
n
Deterministic vs Stochastic Control System
A control System is deterministic if the response to input is predictable

and repeatable.
x(t) y(t)
t t
If not, the control system is a stochastic control system

z(t)
t
Adaptive Control System
The dynamic characteristics of most control systems

are not constant for several reasons.
The effect of small changes on the system

parameters is attenuated in a feedback control
system.
An adaptive control system is required when the

changes in the system parameters are significant.
Learning Control System
A control system that can learn from the

environment it is operating is called a learning
control system.
Classification of Control Systems
Control Systems
Natural Man-made
Manual Automatic
Open-loop Closed-loop
Non-linear linear
Non-linear linear
Time variant Time invariant

Time variant Time invariant
Examples of Control Systems
Water-level float regulator
Examples of Control Systems
Examples of Modern Control Systems
Transfer Function
Transfer Function is the ratio of Laplace transform of the
output to the Laplace transform of the input. Assuming
all initial conditions are zero.
u(t) Plant y(t)
If u ( t ) U ( S ) and
y(t ) Y ( S )
Where is the Laplace operator.

29
Transfer Function
Then the transfer function G(S) of the plant is given
as
Y (S )
G( S )
U (S )
U(S) G(S) Y(S)
30
Why Laplace Transform?
By use of Laplace transform we can convert many
common functions into algebraic function of complex
variable s.
For example

sin t 2
s 2
Or
at 1
e
sa
Where s is a complex variable (complex frequency) and
is given as
s j 31
Laplace Transform of Derivatives
Not only common function can be converted into
simple algebraic expressions but calculus operations
can also be converted into algebraic expressions.
For example
dx(t )
sX ( S ) x( 0)
dt
2
d x(t ) 2 dx( 0 )
2
s X ( S ) x( 0)
dt dt
32
Laplace Transform of Derivatives
In general
d x(t )
n
n 1 n 1
n
s X (S ) s
n
x( 0) x ( 0)
dt
Where x(0) is the initial condition of the system.
33
Example: RC Circuit
u is the input voltage applied at t=0

y is the capacitor voltage
If the capacitor is not already charged then

y(0)=0.
34
Laplace Transform of Integrals
1
x(t )dt X ( S )
s
The time domain integral becomes division by

s in frequency domain.
35
Calculation of the Transfer Function
Consider the following ODE where y(t) is input of the system and
x(t) is the output.
d 2 x(t ) dy(t ) dx(t )
A C B
or dt 2 dt dt
Ax' ' (t ) Cy' (t ) Bx' (t )
Taking the Laplace transform on either sides
A[ s 2 X ( s ) sx(0) x' (0)] C[ sY ( s ) y(0)] B[ sX ( s ) x(0)]
36
Calculation of the Transfer Function
A[ s 2 X ( s ) sx(0) x' (0)] C[ sY ( s ) y(0)] B[ sX ( s ) x(0)]
Considering Initial conditions to zero in order to find the transfer

function of the system
As 2 X ( s ) CsY ( s ) BsX ( s )
Rearranging the above equation
As 2 X ( s ) BsX ( s ) CsY ( s )
X ( s )[ As 2 Bs ] CsY ( s )
X ( s) Cs C

Y ( s ) As Bs As B
2
37
Example
1. Find out the transfer function of the RC network shown in figure-1.
Assume that the capacitor is not initially charged.
Figure-1
2. u(t) and y(t) are the input and output respectively of a system defined by
following ODE. Determine the Transfer Function. Assume there is no any
energy stored in the system.
6u' ' (t ) 3u(t ) y(t )dt 3 y' ' ' (t ) y(t )
38
Transfer Function
In general
Where x is the input of the system and y is the output of

the system.
39
Transfer Function
When order of the denominator polynomial is greater

than the numerator polynomial the transfer function is
said to be proper.
Otherwise improper
40
Transfer Function
Transfer function helps us to check
The stability of the system
Time domain and frequency domain characteristics of the
system
Response of the system for any given input
41
Stability of Control System
There are several meanings of stability, in general
there are two kinds of stability definitions in control
system study.
Absolute Stability
Relative Stability
42
Roots of denominator polynomial of a transfer

function are called poles.
And the roots of numerator polynomials of a

transfer function are called zeros.
43
Poles of the system are represented by x and

zeros of the system are represented by o.
System order is always equal to number of
poles of the transfer function.
Following transfer function represents nth
order plant.
44
Poles is also defined as it is the frequency at which
system becomes infinite. Hence the name pole
where field is infinite.
And zero is the frequency at which system becomes

0.
45
Poles is also defined as it is the frequency at which
system becomes infinite.
Like a magnetic pole or black hole.
46
Relation b/w poles and zeros and frequency
response of the system
The relationship between poles and zeros and the frequency
response of a system comes alive with this 3D pole-zero plot.
Single pole system
47
3D pole-zero plot
System has 1 zero and 2 poles.
48
49
Example
Consider the Transfer function calculated in previous
slides.
X (s) C
G( s )
Y ( s ) As B
the denominato r polynomial is As B 0
The only pole of the system is
B
s
A
50
Examples
Consider the following transfer functions.
Determine
Whether the transfer function is proper or improper
Poles of the system
zeros of the system
Order of the system
s3 G( s )
s
i) G( s ) ii)
s( s 2 ) ( s 1)( s 2)( s 3)
( s 3) 2 s 2 ( s 1)
iii) G( s ) iv) G( s )
s( s 2 10 ) s( s 10 )
51
Stability of Control Systems
The poles and zeros of the system are plotted in s-plane
to check the stability of the system.
j
LHP RHP
Recall s j

s-plane
52
If all the poles of the system lie in left half plane the
system is said to be Stable.
If any of the poles lie in right half plane the system is said
to be unstable.
If pole(s) lie on imaginary axis the system is said to be
marginally stable. j
Absolute stability does not

LHP RHP
depend on location of
zeros of the transfer
function
s-plane
53
Examples
Pole-Zero Map
5
3
stable
2
Imaginary Axis
-1
-2
-3
-4
-5
-5 -4 -3 -2 -1 0 1 2 3 4 5
Real Axis
54
Examples
Pole-Zero Map
5
4
stable
3
2
Imaginary Axis
-1
-2
-3
-4
-5
-5 -4 -3 -2 -1 0 1 2 3 4 5
Real Axis 55
Examples
Pole-Zero Map
5
4
unstable
3
2
Imaginary Axis
-1
-2
-3
-4
-5
-5 -4 -3 -2 -1 0 1 2 3 4 5
Real Axis
56
Examples
Pole-Zero Map
5
3
stable
2
Imaginary Axis
-1
-2
-3
-4
-5
-5 -4 -3 -2 -1 0 1 2 3 4 5
Real Axis
57
Examples
Pole-Zero Map
5
3 Marginally stable
2
Imaginary Axis
-1
-2
-3
-4
-5
-5 -4 -3 -2 -1 0 1 2 3 4 5
Real Axis
58
Examples
Pole-Zero Map
5
4 stable
3
2
Imaginary Axis
-1
-2
-3
-4
-5
-3 -2 -1 0 1 2 3
Real Axis
59
Examples
Pole-Zero Map
4
3
Marginally stable
1
Imaginary Axis
-1
-2
-3
-4
-2 -1.5 -1 -0.5 0 0.5 1 1.5 2
Real Axis
60
Examples
Relative Stability
Pole-Zero Map Pole-Zero Map

5 5
4 4
stable stable
3 3
2 2
Imaginary Axis
Imaginary Axis
1 1
0 0
-1 -1
-2 -2
-3 -3
-4 -4
-5 -5
-5 -4 -3 -2 -1 0 1 2 3 4 5 -6 -4 -2 0 2 4
Real Axis Real Axis
61
For example
C
G( s ) , if A 1, B 3 and C 10
As B
Then the only pole of the system lie at
pole 3
j
LHP RHP
X
-3
s-plane
62
Examples
Consider the following transfer functions.
Determine whether the transfer function is proper or improper
Calculate the Poles and zeros of the system
Determine the order of the system
Draw the pole-zero map
Determine the Stability of the system
s3 G( s )
s
i) G( s ) ii)
s( s 2 ) ( s 1)( s 2)( s 3)
( s 3) 2 s 2 ( s 1)
iii) G( s ) iv) G( s )
s( s 2 10 ) s( s 10 )
63
Another definition of Stability
The system is said to be stable if for any bounded
input the output of the system is also bounded
(BIBO).
Thus the for any bounded input the output either
remain constant or decrease with time.
u(t) overshoot
y(t)
1
Plant 1
t
t
Unit Step Input
Output
64
Another definition of Stability
If for any bounded input the output is not
bounded the system is said to be unstable.
u(t)
y(t)
1
e at
Plant
t
t
Unit Step Input
Output
65
BIBO vs Transfer Function
For example
Y ( s) 1 Y ( s) 1
G1 ( s) G2 ( s)
U ( s) s 3 U ( s) s 3
Pole-Zero Map Pole-Zero Map
4 4
unstable
3 stable 3
2 2
1 1
Imaginary Axis
Imaginary Axis
0 0
-1 -1
-2 -2
-3 -3
-4 -4
-4 -2 0 2 4 -4 -2 0 2 4
Real Axis Real Axis
For example
Y ( s) 1 Y ( s) 1
G1 ( s) G2 ( s)
U ( s) s 3 U ( s) s 3
1 Y (s)
1 1 1 Y (s) 1
G1 ( s ) 1
G2 ( s) 1
1
U ( s) s3 U (s) s 3
y (t ) e 3t u (t ) y (t ) e3t u (t )
For example
3t
y(t ) e u (t ) y (t ) e3t u (t )
12
exp(-3t)*u(t) x 10 exp(3t)*u(t)
1 12
10
0.8
8
0.6
6
0.4
4
0.2
2
0 0
0 1 2 3 4 0 2 4 6 8 10
Whenever one or more than one poles are in
RHP the solution of dynamic equations
contains increasing exponential terms.
Such as e3t .
That makes the response of the system
unbounded and hence the overall response of
the system is unstable.
Types of Systems
Static System: If a system does not change
with time, it is called a static system.
Dynamic System: If a system changes with
time, it is called a dynamic system.
70
Dynamic Systems
A system is said to be dynamic if its current output may depend on
the past history as well as the present values of the input variables.
Mathematically,
y(t ) [u( ),0 t ]

u : Input, t : Time
Example: A moving mass
y
u
M
Model: Force=Mass x Acceleration
My u
Ways to Study a System
System
Experiment with actual Experiment with a

System model of the System
Physical Model Mathematical Model
Analytical Solution
Simulation
Frequency Domain Time Domain Hybrid Domain
72
Model
A model is a simplified representation or
abstraction of reality.
Reality is generally too complex to copy
exactly.
Much of the complexity is actually irrelevant
in problem solving.
73
Types of Models
Model
Physical Mathematical Computer
Static Dynamic Static Dynamic Static Dynamic
74
What is Mathematical Model?
A set of mathematical equations (e.g., differential eqs.) that
describes the input-output behavior of a system.
What is a model used for?

Simulation
Prediction/Forecasting
Prognostics/Diagnostics
Design/Performance Evaluation
Control System Design
Classification of Mathematical Models
Linear vs. Non-linear
Deterministic vs. Probabilistic (Stochastic)
Static vs. Dynamic
Discrete vs. Continuous
White box, black box and gray box
76
Black Box Model
When only input and output are known.
Internal dynamics are either too complex or
unknown.
Input Output
Easy to Model
77
Black Box Model
Consider the example of a heat radiating system.
78
Black Box Model
Consider the example of a heat radiating system.
Heat Raadiating
Heat System
Raadiating System
Room 3535
Valve
Temperature Room Temperature
Temperature in Degree Celsius (y)

Temperature in Degree Celsius
Position 3030 Room Temperature
(oC) quadratic Fit
2525
0 0
20
20 y = 0.31*x 2 + 0.046*x + 0.64
2 3
15
15
4 6
10
10
6 12
5
5
8 20
0
10 33 00
0
2
2
4
4
6
6
8
8
10
10
Valve Position
Valve Position (x)
79
Grey Box Model
When input and output and some information
about the internal dynamics of the system is
known.
u(t) y(t)
y[u(t), t]
Easier than white box Modelling.
80
White Box Model
When input and output and internal dynamics
of the system is known.
dy(t ) du(t ) d 2 y(t )

u(t) 3 y(t)
dt dt dt 2
One should know have complete knowledge

of the system to derive a white box model.
81
Mathematical Modelling Basics
Mathematical model of a real world system is derived using a

combination of physical laws and/or experimental means
Physical laws are used to determine the model structure (linear

or nonlinear) and order.
The parameters of the model are often estimated and/or
validated experimentally.
Mathematical model of a dynamic system can often be expressed
as a system of differential (difference in the case of discrete-time
systems) equations
Different Types of Lumped-Parameter Models
System Type Model Type
Nonlinear Input-output differential equation
Linear State equations
Linear Time
Invariant Transfer function
Approach to dynamic systems
Define the system and its components.

Formulate the mathematical model and list the necessary
assumptions.
Write the differential equations describing the model.
Solve the equations for the desired output variables.
Examine the solutions and the assumptions.
If necessary, reanalyze or redesign the system.
84
Simulation
Computer simulation is the discipline of
designing a model of an actual or theoretical
physical system, executing the model on a
digital computer, and analyzing the execution
output.
Simulation embodies the principle of
``learning by doing'' --- to learn about the
system we must first build a model of some
sort and then operate the model.
85
Advantages to Simulation
Can be used to study existing systems without
disrupting the ongoing operations.
Proposed systems can be tested before committing

resources.
Allows us to control time.
Allows us to gain insight into which variables are

most important to system performance.
86
Disadvantages to Simulation
Model building is an art as well as a science. The
quality of the analysis depends on the quality of the
model and the skill of the modeler.
Simulation results are sometimes hard to interpret.
Simulation analysis can be time consuming and

expensive.
Should not be used when an analytical method would

provide for quicker results.
87
To download this lecture visit
http://imtiazhussainkalwar.weebly.com/
END OF LECTURE-1

Lecture 1 Introduction Review of Classical Control

Uploaded by

Copyright:

Available Formats

Lecture 1 Introduction Review of Classical Control

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Lecture 1 Introduction Review of Classical Control

Uploaded by

Copyright:

Available Formats

Advanced Control Systems (ACS)

Dr. Imtiaz Hussain

1. Burns R. Advanced Control Engineering, Butterworth

Automatic Control System

Examples:- Washing Machine, Toaster, Electric Fan

Since in open loop control systems reference input is not

Therefore, the accuracy of the system depends on calibration.

The performance of open loop system is severely affected by the

Closed-Loop Control Systems utilizes feedback to compare the actual

Examples:- Refrigerator, Iron

A system that maintains a prescribed relationship between the output

Input + error Output

Feedback can be positive or negative.

A Servo System (or servomechanism) is a feedback control system in

Antenna Positioning System Modular Servo System (MS150)

u(t) Process y(t)

y(t ) 2u(t ) 1 y(t ) 3u(t ) 5

Adhesion Characteristics of Road

When the magnitude of signals 0.1

When the characteristics of the system do not depend upon time

Time varying control system is a system in which one or more

Control system that can be described by ordinary differential equations

In continuous data control system all system variables are function of a

A control System is deterministic if the response to input is predictable

If not, the control system is a stochastic control system

The dynamic characteristics of most control systems

The effect of small changes on the system

An adaptive control system is required when the

A control system that can learn from the

Time variant Time invariant

u(t) Plant y(t)

Where is the Laplace operator.

U(S) G(S) Y(S)

Where x(0) is the initial condition of the system.

u is the input voltage applied at t=0

If the capacitor is not already charged then

The time domain integral becomes division by

Ax' ' (t ) Cy' (t ) Bx' (t )

Taking the Laplace transform on either sides

A[ s 2 X ( s ) sx(0) x' (0)] C[ sY ( s ) y(0)] B[ sX ( s ) x(0)]

A[ s 2 X ( s ) sx(0) x' (0)] C[ sY ( s ) y(0)] B[ sX ( s ) x(0)]

Considering Initial conditions to zero in order to find the transfer

6u' ' (t ) 3u(t ) y(t )dt 3 y' ' ' (t ) y(t )

Where x is the input of the system and y is the output of

When order of the denominator polynomial is greater

The stability of the system

Time domain and frequency domain characteristics of the

Response of the system for any given input

Roots of denominator polynomial of a transfer

And the roots of numerator polynomials of a

Poles of the system are represented by x and

And zero is the frequency at which system becomes

Single pole system

the denominato r polynomial is As B 0

The only pole of the system is

Absolute stability does not

Pole-Zero Map Pole-Zero Map

y(t ) [u( ),0 t ]

Experiment with actual Experiment with a