Structure and delivery

2 lectures per week (90 minutes each)

Students will be expected to attend the lectures.

Students will be expected to have undertaken a

wide range of reading
 Contents
Concept of Stress Bearing Stress in Connections
Review of Statics Stress Analysis & Design Example
Structure Free-Body Diagram Rod & Boom Normal Stresses
Component Free-Body Diagram Pin Shearing Stresses
Method of Joints Pin Bearing Stresses
Stress Analysis Stress in Two Force Members
Design Stress on an Oblique Plane
Axial Loading: Normal Stress Maximum Stresses
Centric & Eccentric Loading Stress Under General Loadings
Shearing Stress State of Stress
Shearing Stress Examples Factor of Safety

1-2
 Concept of Stress
The main objective of the study of mechanics of materials is to
provide the future engineer with the means of analyzing and
designing various machines and load bearing structures.

Both the analysis and design of a given structure involve the

determination of stresses and deformations. This chapter is devoted
to the concept of stress.

In this chapter you are going to study the concept of stress in a

member of a structure, you will consider successively the normal
stresses in a member under axial loading, the shearing stresses
caused by opposite transverse forces, and the bearing stresses
created by bolts and pins in the members.

1-3
Review of Statics
The structure is designed to
support a 30 kN load
The structure consists of a
boom and rod joined by pins
(zero moment connections) at
the junctions and supports
Perform a static analysis to
determine the internal force in
each structural member and the
reaction forces at the supports

1-4
Structure Free-Body
Diagram
Structure is detached from supports and
the loads and reaction forces are
indicated
Conditions for static equilibrium:
M C 0 Ax 0.6 m 30 kN 0.8 m
Ax 40 kN
Fx 0 Ax C x
C x Ax 40 kN
Fy 0 Ay C y 30 kN 0
Ay C y 30 kN

Ay and Cy can not be determined from

these equations

1-5
Component Free-Body
Diagram
In addition to the complete structure, each
component must satisfy the conditions for
static equilibrium
Consider a free-body diagram for the boom:
M B 0 Ay 0.8 m
Ay 0
substitute into the structure equilibrium
equation
C y 30 kN

Results:
A 40 kN C x 40 kN C y 30 kN

Reaction forces are directed along boom

and rod

1-6
Method of Joints
The boom and rod are 2-force members, i.e.,
the members are subjected to only two forces
which are applied at member ends

For equilibrium, the forces must be parallel to

to an axis between the force application points,
equal in magnitude, and in opposite directions

Joints must satisfy the conditions for static

equilibrium which may be expressed in the
form of a force triangle:

FB 0
FAB FBC 30 kN

4 5 3
FAB 40 kN FBC 50 kN

1-7
 Stress Analysis
Can the structure safely support the 30kN load?
From a statics analysis
FAB = 40kN (compression) &FBC = 50kN (tension)
Results obtained in the preceding section do not tell
us whether the given load can be safely supported
or not. This will be checked by analysis and design
of a structure by determination of stresses and
deformation
At any section through member BC, the
internal force is 50 kN with a force intensity
or stress of
dBC = 20 mm P 50 103 N
BC 159 MPa
A 314 10-6 m 2

From the material properties for steel, the

allowable stress is
all 165 MPa
Conclusion: the strength of member BC is
adequate
1-8
Design
Design of new structures requires selection of
appropriate materials and component dimensions
to meet performance requirements
For reasons based on cost, weight, availability,
etc., the choice is made to construct the rod from
aluminum all= 100 MPa) What is an
appropriate choice for the rod diameter?
P P 50 103 N
all A 500 10 6 m 2
A all 100 106 Pa
d2
A
4

d
4A


4 500 10 6 m 2
2.52 10 2 m 25.2 mm

An aluminum rod 26 mm or more in diameter is

adequate
1-9
Axial Loading: Normal Stress
The resultant of the internal forces for an axially
loaded member is normal to a section cut
perpendicular to the member axis.

The force intensity on that section is defined as

the normal stress.
F P
lim ave
A0 A A

The normal stress at a particular point may not be

equal to the average stress but the resultant of the
stress distribution must satisfy
P ave A dF dA
A

The detailed distribution of stress is statically

indeterminate, i.e., can not be found from statics
alone.
1 - 10
Centric & Eccentric Loading
A uniform distribution of stress in a section
infers that the line of action for the resultant of
the internal forces passes through the centroid
of the section.

A uniform distribution of stress is only

possible if the concentrated loads on the end
sections of two-force members are applied at
the section centroids. This is referred to as
centric loading.

If a two-force member is eccentrically

loaded, then the resultant of the stress
distribution in a section must yield an axial
force and a moment.

The stress distributions in eccentrically loaded

members cannot be uniform or symmetric.
1 - 11
Shearing Stress
Forces P and P are applied transversely to the
member AB.
Corresponding internal forces act in the plane
of section C and are called shearing forces.
The resultant of the internal shear force
distribution is defined as the shear of the section
and is equal to the load P.
The corresponding average shear stress is,
P
ave
A
Shear stress distribution varies from zero at the
member surfaces to maximum values that may be
much larger than the average value.
The shear stress distribution cannot be assumed to
be uniform.
1 - 12
Shearing Stress Examples
Single Shear Double Shear

P F P F
ave ave
A A A 2A

1 - 13
Bearing Stress in Connections
Bolts, rivets, and pins create
stresses on the points of
contact or bearing surfaces of
the members they connect.

The resultant of the force

distribution on the surface is
equal and opposite to the force
exerted on the pin.

Corresponding average force

intensity is called the bearing
stress,
P P
b
A td

1 - 14
Stress Analysis & Design
Example
Would like to determine the
stresses in the members and
connections of the structure
shown.

From a statics analysis:

FAB = 40 kN (compression)

FBC = 50 kN (tension)
Must consider maximum
normal stresses in AB and
BC, and the shearing stress
and bearing stress at each
pinned connection

1 - 15
Rod & Boom Normal
Stresses
The rod is in tension with an axial force of 50 kN.

At the rod center, the average normal stress in the

circular cross-section (A = 314x10-6m2) is BC = +159
MPa.
At the flattened rod ends, the smallest cross-sectional
area occurs at the pin centerline,
A 20 mm 40 mm 25 mm 300 10 6 m 2

P 50 103 N
BC ,end 167 MPa
A 300 10 6 m 2

The boom is in compression with an axial force of 40

kN and average normal stress of 26.7 MPa.

The minimum area sections at the boom ends are

unstressed since the boom is in compression.

1 - 16
Pin Shearing Stresses
The cross-sectional area for pins at A, B,
and C,
2
25 mm
2
A r 491 10 6 m 2
2

The force on the pin at C is equal to the

force exerted by the rod BC,
P 50 103 N
C , ave 6 2
102 MPa
A 49110 m

The pin at A is in double shear with a

total force equal to the force exerted by
the boom AB,
P 20 kN
A, ave 6 2
40.7 MPa
A 49110 m

1 - 17
Pin Shearing Stresses
Divide the pin at B into sections to determine
the section with the largest shear force,
PE 15 kN
PG 25 kN (largest)

Evaluate the corresponding average

shearing stress,
PG 25 kN
B, ave 50.9 MPa
A 49110 6 m 2

1 - 18
Pin Bearing Stresses

To determine the bearing stress at A in the boom AB,

we have t = 30 mm and d = 25 mm,
P 40 kN
b 53.3 MPa
td 30 mm 25 mm

To determine the bearing stress at A in the bracket,

we have t = 2(25 mm) = 50 mm and d = 25 mm,
P 40 kN
b 32.0 MPa
td 50 mm 25 mm

1 - 19
Stress in Two Force Members
Axial forces on a two force
member result in only normal
stresses on a plane cut
perpendicular to the member axis.

Transverse forces on bolts and

pins result in only shear stresses
on the plane perpendicular to bolt
or pin axis.

Will show that either axial or

transverse forces may produce both
normal and shear stresses with respect
to a plane other than one cut
perpendicular to the member axis.

1 - 20
Stress on an Oblique Plane
Pass a section through the member forming
an angle with the normal plane.

From equilibrium conditions, the

distributed forces (stresses) on the plane
must be equivalent to the force P.

Resolve P into components normal and

tangential to the oblique section,
F P cos V P sin

The average normal and shear stresses on

the oblique plane are
F P cos P
cos 2
A A0 A0
cos
V P sin P
sin cos
A A0 A0
cos
1 - 21
Maximum Stresses
Normal and shearing stresses on an oblique
plane
P P
cos 2 sin cos
A0 A0

The maximum normal stress occurs when the

reference plane is perpendicular to the member
axis,
P
m 0
A0

The maximum shear stress occurs for a plane at

+ 45o with respect to the axis,
P P
m sin 45 cos 45
A0 2 A0

1 - 22
Stress Under General
Loadings
A member subjected to a general
combination of loads is cut into
two segments by a plane passing
through Q

The distribution of internal stress

components may be defined as,
F x
x lim
A0 A

V yx Vzx
xy lim xz lim
A 0 A A0 A

For equilibrium, an equal and

opposite internal force and stress
distribution must be exerted on
the other segment of the member.
1 - 23
State of Stress
Stress components are defined for the planes
cut parallel to the x, y and z axes. For
equilibrium, equal and opposite stresses are
exerted on the hidden planes.
The combination of forces generated by the
stresses must satisfy the conditions for
equilibrium:
Fx Fy Fz 0
Mx M y Mz 0
Consider the moments about the z axis:
M z 0 xy A a yx A a
xy yx
similarly, yz zy and yz zy

It follows that only 6 components of stress

are required to define the complete state of
stress 1 - 24
 Factor of Safety
Structural members or machines Factor of safety considerations:
must be designed such that the uncertainty in material properties
working stresses are less than the uncertainty of loadings
ultimate strength of the material. uncertainty of analyses
number of loading cycles
FS Factor of safety
types of failure
u ultimate stress
FS maintenance requirements and
all allowable stress
deterioration effects
importance of member to structures
integrity
risk to life and property
influence on machine function

1 - 25